Popular Post Nestor Posted December 10, 2016 Popular Post Report Posted December 10, 2016 Xmas gift. Been picking away at it after 12 hr shifts, but hope to have it done this weekend. Box sides will be "ebonized" with India ink. The rest will be a cherry dye stain. ETA: "Sides" refers to the left and right sides. Plans from Woodsmith. Base, front, and back planed down to 1/2". Lid and sides left at 3/4" for the curves. Curved lid rough cut with table saw. Block plane to smooth the lid followed by 60 grit sandpaper. Curly Maple is a PITA to work with and gouges really easy. Give your plane some TLC with your sharpening stones before commencing. Sides will be assembled with dowels. Holes drilled before glue-up. Note the cove in the front done at the router table with a 1/2" cove bit. Same cove bit for the matching finger lift and to start the underside profile. Waste cleaned out with a dado set. That's it for now. Need to give my plane more TLC before I clean up the underside. Stay tuned... Sent from my iPad using Tapatalk 4 Quote
..Kev Posted December 10, 2016 Report Posted December 10, 2016 Looking very cool! Seems a shame to add ink and stain to that really nice maple! Quote
Nestor Posted December 10, 2016 Author Report Posted December 10, 2016 Looking very cool! Seems a shame to add ink and stain to that really nice maple! If it works according to the plans, the dye stain and gloss finish will make the grain stand out in dramatic fashion. Sent from my iPad using Tapatalk Quote
..Kev Posted December 10, 2016 Report Posted December 10, 2016 Just now, Nestor said: If it works according to the plans, the dye stain and gloss finish will make the grain stand out in dramatic fashion. Sent from my iPad using Tapatalk Ah, ok.. So you're going to apply and sand back to enhance the grain.. Got it.. 1 Quote
Nestor Posted December 10, 2016 Author Report Posted December 10, 2016 Ah, ok.. So you're going to apply and sand back to enhance the grain.. Got it.. From the video I've watched, no sanding appears necessary. I picked a couple of colours, including a "vintage" cherry I may blend in to make it more brown. I'll snap some shots when I stain a test piece. Sent from my iPad using Tapatalk Quote
..Kev Posted December 10, 2016 Report Posted December 10, 2016 Suggest some trial on scrap first.. Looking forward to seeing it! I think Marc did a video on this as well.. Quote
shaneymack Posted December 10, 2016 Report Posted December 10, 2016 Thats looking great, Nestor. Some nice figure in that maple. Hope the ink and dye does make it stand out like you say. I look forward to seeing this finished. Sent from my SM-N910W8 using Tapatalk Quote
Nestor Posted December 10, 2016 Author Report Posted December 10, 2016 Just to clarify, only the left and right side pieces will be getting the India ink treatment. The rest will be dye stain. Apologies if that isn't clear in my OP. Sent from my iPad using Tapatalk Quote
wtnhighlander Posted December 10, 2016 Report Posted December 10, 2016 I think its going to look pretty sweet! What sort of hinge does this box use? Quote
Nestor Posted December 10, 2016 Author Report Posted December 10, 2016 I think its going to look pretty sweet! What sort of hinge does this box use? Solid brass from LV. Was looking for something darker but they will have to do. For their size, they're ridiculously expensive. :-/ Sent from my iPhone using Tapatalk Quote
sheperd80 Posted December 11, 2016 Report Posted December 11, 2016 Looking good, interested to see this ink and dye finish Sent from my SAMSUNG-SM-G890A using Tapatalk Quote
bleedinblue Posted December 11, 2016 Report Posted December 11, 2016 How do you cut the curved lid on the TS? I don't think I've seen that done before Quote
Nestor Posted December 11, 2016 Author Report Posted December 11, 2016 Okay, my entire update post disappeared. Sent from my iPad using Tapatalk Quote
MisterDrow Posted December 11, 2016 Report Posted December 11, 2016 How do you cut the curved lid on the TS? I don't think I've seen that done before I think he just cut shallow angles on it while the piece was on edge and then cleaned it up with a block plane and sand paper. Correct me if I am wrong on this, OP. 1 Quote
bleedinblue Posted December 11, 2016 Report Posted December 11, 2016 1 hour ago, MisterDrow said: I think he just cut shallow angles on it while the piece was on edge and then cleaned it up with a block plane and sand paper. Correct me if I am wrong on this, OP. That makes sense. Quote
Popular Post Nestor Posted December 12, 2016 Author Popular Post Report Posted December 12, 2016 Let's try this again. Bit of a setback last night. More on it in a bit. After an hour of tear-outs and gouges with the block plane trying to smooth out the scoring grooves left by the dado blades, I headed back to the router table. My bowl & tray bit made short work of the remaining clean-up, and the rounded profile made sure it was ridge-free. Here's where things went south. Because the pieces are small and the blade is high, the plans recommend mounting the pieces on a backer board with carpet tape. Everything went along swimmingly until the second pass, where the backer board slipped. Ever have that feeling you know you've ruined a piece but you are committed to the cut and need to finish it? So that's where I decided to shut things down Sat. night. Today's progress next post..... Sent from my iPad using Tapatalk Sunday update: Today was better. After cutting some new pieces, I used dowel centres to mark the holes and drilled them at the press. I headed to the router table and cut a shallow 1" cove matching the templates I glued on the ends. This helps to line up the saw for the final rough cuts. Remounted the pieces on a nice beefy piece of white oak. No slippage! After copious sanding, a test fit. Time to eat, drink, and be merry, for tomorrow we dye! Sent from my iPad using Tapatalk 5 Quote
Nestor Posted December 12, 2016 Author Report Posted December 12, 2016 P.s. Tapatalk has been doing strange things. My previous post was supposed to be two separate ones. Sent from my iPad using Tapatalk Quote
Tpt life Posted December 12, 2016 Report Posted December 12, 2016 That's the forum software. It will merge replies when you get there before someone else. What carpet tape slipped on you? Quote
Nestor Posted December 12, 2016 Author Report Posted December 12, 2016 That's the forum software. It will merge replies when you get there before someone else. What carpet tape slipped on you? Ah. Noted. The backer board itself shifted into the blade as I was passing it through. Tape was fine. The 1 3/4" oak was much more stable. Sent from my iPad using Tapatalk Quote
Nestor Posted December 12, 2016 Author Report Posted December 12, 2016 Test pieces. From the top down: 50/50 mix-- Cherry-- Vintage Cherry ETA: the dye stained lid, front , and back will be flanked by the ebonized end pieces. Sent from my iPad using Tapatalk 1 Quote
mat60 Posted December 12, 2016 Report Posted December 12, 2016 I vote for 50/50 myself. Great project also. Quote
Nestor Posted December 12, 2016 Author Report Posted December 12, 2016 I vote for 50/50 myself. Great project also. Thanks. I'm leaning towards the mix as well. The picture in the plans has a more gold than red, but I think this will work. Sent from my iPad using Tapatalk Quote
mat60 Posted December 12, 2016 Report Posted December 12, 2016 4 hours ago, Nestor said: Thanks. I'm leaning towards the mix as well. The picture in the plans has a more gold than red, but I think this will work. Sent from my iPad using Tapatalk I thought it would add some pop to it but if it doesnt look good when its done good please dont tell the guys I said anything. Quote
JosephThomas Posted December 12, 2016 Report Posted December 12, 2016 3 hours ago, shaneymack said: i vote vintage cherry. Same...it looks awesome. 50/50 isn't bad though....but just the cherry looks pretty fake. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.