Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Curly Maple Treasure Box

Featured Replies

  • Popular Post

Xmas gift. Been picking away at it after 12 hr shifts, but hope to have it done this weekend.

Box sides will be "ebonized" with India ink. The rest will be a cherry dye stain.

ETA: "Sides" refers to the left and right sides.

Plans from Woodsmith.

Base, front, and back planed down to 1/2". Lid and sides left at 3/4" for the curves.

9beaef61386c2735d2c6c559a763f43e.jpg

Curved lid rough cut with table saw.

f1f2c75721f252f08a9fec02e801c0ce.jpg

Block plane to smooth the lid followed by 60 grit sandpaper.

Curly Maple is a PITA to work with and gouges really easy. Give your plane some TLC with your sharpening stones before commencing.

df964d94a87bffc5558d9992b0481b1b.jpg

Sides will be assembled with dowels. Holes drilled before glue-up. Note the cove in the front done at the router table with a 1/2" cove bit.

e2afddbbbff91b8213fd5fc18d5d214e.jpg

Same cove bit for the matching finger lift and to start the underside profile.

7bb9f49b48e812fe66f4b2187a053bdd.jpg

Waste cleaned out with a dado set.

32391ab89cb7afab002ffaa829ddd9e6.jpg

That's it for now. Need to give my plane more TLC before I clean up the underside.

Stay tuned...

Sent from my iPad using Tapatalk

Looking very cool!  Seems a shame to add ink and stain to that really nice maple!

  • Author
Looking very cool!  Seems a shame to add ink and stain to that really nice maple!

If it works according to the plans, the dye stain and gloss finish will make the grain stand out in dramatic fashion.

Sent from my iPad using Tapatalk

Just now, Nestor said:

If it works according to the plans, the dye stain and gloss finish will make the grain stand out in dramatic fashion.

Sent from my iPad using Tapatalk

Ah, ok..  So you're going to apply and sand back to enhance the grain..  Got it..  

  • Author
Ah, ok..  So you're going to apply and sand back to enhance the grain..  Got it..  

From the video I've watched, no sanding appears necessary.

I picked a couple of colours, including a "vintage" cherry I may blend in to make it more brown. I'll snap some shots when I stain a test piece.

Sent from my iPad using Tapatalk

Suggest some trial on scrap first..  Looking forward to seeing it!

I think Marc did a video on this as well..

Thats looking great, Nestor. Some nice figure in that maple. Hope the ink and dye does make it stand out like you say. I look forward to seeing this finished.

Sent from my SM-N910W8 using Tapatalk

  • Author

Just to clarify, only the left and right side pieces will be getting the India ink treatment. The rest will be dye stain. Apologies if that isn't clear in my OP.

Sent from my iPad using Tapatalk

  • Author
I think its going to look pretty sweet! What sort of hinge does this box use?

Solid brass from LV. Was looking for something darker but they will have to do.

For their size, they're ridiculously expensive. :-/

Sent from my iPhone using Tapatalk

Looking good, interested to see this ink and dye finish

Sent from my SAMSUNG-SM-G890A using Tapatalk

How do you cut the curved lid on the TS?  I don't think I've seen that done before

  • Author

Okay, my entire update post disappeared.

[emoji35]

Sent from my iPad using Tapatalk

How do you cut the curved lid on the TS?  I don't think I've seen that done before

I think he just cut shallow angles on it while the piece was on edge and then cleaned it up with a block plane and sand paper.

Correct me if I am wrong on this, OP.

1 hour ago, MisterDrow said:

I think he just cut shallow angles on it while the piece was on edge and then cleaned it up with a block plane and sand paper.

Correct me if I am wrong on this, OP.

That makes sense.

  • Author
  • Popular Post

Let's try this again.

Bit of a setback last night. More on it in a bit.

After an hour of tear-outs and gouges with the block plane trying to smooth out the scoring grooves left by the dado blades, I headed back to the router table.

My bowl & tray bit made short work of the remaining clean-up, and the rounded profile made sure it was ridge-free.

fdb19bac922aed0c76bff15a3b1e5597.jpg

Here's where things went south.

Because the pieces are small and the blade is high, the plans recommend mounting the pieces on a backer board with carpet tape.

Everything went along swimmingly until the second pass, where the backer board slipped.

Ever have that feeling you know you've ruined a piece but you are committed to the cut and need to finish it?

96a9f0e990ca401c254ab4d461134a41.jpg

So that's where I decided to shut things down Sat. night.

Today's progress next post.....

Sent from my iPad using Tapatalk

Sunday update:

Today was better.

After cutting some new pieces, I used dowel centres to mark the holes and drilled them at the press.

59186f96a647d87ef912fc516791fecc.jpg

I headed to the router table and cut a shallow 1" cove matching the templates I glued on the ends. This helps to line up the saw for the final rough cuts.

a0b2529f2cf75cc7d50515047a371301.jpg

Remounted the pieces on a nice beefy piece of white oak.

a5dc422479fece050e1f4383cc1d38b8.jpg

No slippage!

cd446b31744b5528b3dc4b15a717138a.jpg

After copious sanding, a test fit.

5531a0b1fc69683fd1def16616a4cb3c.jpg

Time to eat, drink, and be merry, for tomorrow we dye!

Sent from my iPad using Tapatalk

  • Author

P.s. Tapatalk has been doing strange things. My previous post was supposed to be two separate ones.

Sent from my iPad using Tapatalk

  • Author
That's the forum software. It will merge replies when you get there before someone else. What carpet tape slipped on you?

Ah. Noted.

The backer board itself shifted into the blade as I was passing it through. Tape was fine. The 1 3/4" oak was much more stable.

Sent from my iPad using Tapatalk

  • Author

Test pieces. From the top down:

50/50 mix--

Cherry--

Vintage Cherry

ETA: the dye stained lid, front , and back will be flanked by the ebonized end pieces.

13617e7583556d88586861fb802ef3e6.jpg

Sent from my iPad using Tapatalk

I vote for 50/50 myself.   Great project also.

  • Author
I vote for 50/50 myself.   Great project also.

Thanks. I'm leaning towards the mix as well.

The picture in the plans has a more gold than red, but I think this will work.

Sent from my iPad using Tapatalk

4 hours ago, Nestor said:

Thanks. I'm leaning towards the mix as well.

The picture in the plans has a more gold than red, but I think this will work.

Sent from my iPad using Tapatalk

I thought it would add some pop to it but if it doesnt look good when its done good please dont tell the guys I said anything.

3 hours ago, shaneymack said:

i vote vintage cherry.

Same...it looks awesome. 50/50 isn't bad though....but just the cherry looks pretty fake.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.