Immortan D Posted March 17, 2017 Report Posted March 17, 2017 1 hour ago, C Shaffer said: I am not sure if this is a digression or non-sequitor, but a tenon I undercut shoulder and face with a chisel at the corner. Half laps are different as the edge shows so I don't use a router plane there. The diamond pointed irons also make skewing cuts rather simple. For the record D, I like seeing how you do things. I just thought the first comment overstated. I don't have one of those diamond pointy irons. I will give them a try. It's all good BTW. Quote
treesner Posted March 18, 2017 Author Report Posted March 18, 2017 Ultimately, my point is that they are all very nice router planes and will do the job. Each has their pros and cons. Now, I did go look at the prices and the Walke is over double the price of the LV or LN. So, with this in mind, I would probably tend to go with the LN router plane and their rabbited block plane (for about the same price) and get even more versatility in my shop. To each their own. It's your shop, your money, and your work flow. You have to do what's best for your needs. Thanks for your input, I was looking at a rabbeting block plane as I have no shoulder plane. Thoughts on the rabbeting block plane vs the skew block plane that can also remove the side plate to make it rabbeting? Sent from my iPhone using Tapatalk Quote
Immortan D Posted March 18, 2017 Report Posted March 18, 2017 I have the LN skew block plane. It's a great plane for rabbetting, it removes a lot of material quickly. I do not recommend it as a shoulder plane replacement though. Quote
..Kev Posted March 18, 2017 Report Posted March 18, 2017 1 hour ago, treesner said: Thanks for your input, I was looking at a rabbeting block plane as I have no shoulder plane. Thoughts on the rabbeting block plane vs the skew block plane that can also remove the side plate to make it rabbeting? Sent from my iPhone using Tapatalk I don't have the skew so, can't comment accordingly. I am perfectly happy with the router and the rabbiting block though.. Quote
treesner Posted March 18, 2017 Author Report Posted March 18, 2017 I don't have the skew so, can't comment accordingly. I am perfectly happy with the router and the rabbiting block though.. Would you say it replaces a shoulder plane? Sent from my iPhone using Tapatalk Quote
Tpt life Posted March 18, 2017 Report Posted March 18, 2017 3 hours ago, treesner said: Would you say it replaces a shoulder plane? The shoulder and rabetting block are really only comparable because they can clean into corners. I think two things got confused in this thread. Someone early suggested trimming the face of a tenon with a shoulder plane. Shoulder planes are narrow enough to not be highly desired on tenons that are deeper than the plane is wide. That comment was also made early on. We spent a while talking about tenon faces only from a router plane perspective. The rabbet plane is my preferred method of trimming faces, but I didn't always have one. For tenon shoulders, the opposite is considered. Here the rabetting block or bench planes are so wide that you can lose some control over registration and wind up out of square while trimming a shoulder. This is not to say guys don't do either operation, but I wouldn't suggest them as efficient or easy compared to using the tools for their intended use. Quote
..Kev Posted March 19, 2017 Report Posted March 19, 2017 18 hours ago, treesner said: Would you say it replaces a shoulder plane? Sent from my iPhone using Tapatalk No but, it would delay the "want" for a shoulder plane. The draw back with the rabbited block is your hand position on the tool. A shoulder plane gets your hand up higher and out of the way of a thick shoulder. Quote
Llama Posted March 19, 2017 Report Posted March 19, 2017 19 hours ago, treesner said: Would you say it replaces a shoulder plane? No. Quote
treesner Posted March 19, 2017 Author Report Posted March 19, 2017 The shoulder and rabetting block are really only comparable because they can clean into corners. I think two things got confused in this thread. Someone early suggested trimming the face of a tenon with a shoulder plane. Shoulder planes are narrow enough to not be highly desired on tenons that are deeper than the plane is wide. That comment was also made early on. We spent a while talking about tenon faces only from a router plane perspective. The rabbet plane is my preferred method of trimming faces, but I didn't always have one. For tenon shoulders, the opposite is considered. Here the rabetting block or bench planes are so wide that you can lose some control over registration and wind up out of square while trimming a shoulder. This is not to say guys don't do either operation, but I wouldn't suggest them as efficient or easy compared to using the tools for their intended use. Shoot looks like I've got another 500 dollars in planes to buy hah Quote
Llama Posted March 19, 2017 Report Posted March 19, 2017 1 minute ago, treesner said: Shoot looks like I've got another 500 dollars in planes to buy hah That's it? You're WAY ahead of me then! Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.