Recommended Posts

Posted

Building 3 corner shelves. Giving each a nice edge with the router.

 

The first two went fine.

 

But the third one grabs the wood and tears it up when I begin the final pass.

(Doing 3 passes in trying to avoid this problem from hogging out too much.)

 

Thoughts?7fca623bb321a1ac33cb1337a37c50c5.jpg

 

Sent from my MotoE2(4G-LTE) using Tapatalk

 

 

Posted
You're routing uphill, Collin.  Against the grain.  Think of petting a cat...how one direction works way better than the other...

 

I see. I should turn it around for that end profile.

( Big Duh in my head right now.)

 

Sent from my MotoE2(4G-LTE) using Tapatalk

 

 

Posted

Then again ... I'm​ brain dead today. Can't figure out the geometry. If I flip the piece then I need an inverse bit ... That can't be it ... Alas

 

And the other two came out so well.

 

Sent from my MotoE2(4G-LTE) using Tapatalk

 

 

Posted
2 hours ago, collinb said:

 

And the other two came out so well.

 

Sent from my MotoE2(4G-LTE) using Tapatalk

 

 

Then consider yourself lucky you have two other pieces left. Bad tear out is the best bad case. The work piece exploding and shooting back at you with a bit still spinning 15000 rpm  isn't an old wives tale. 

Posted

Clamp a piece of scrap against that edge for support. Climb cutting is another possibility. See if you can find a video or article about climb cutting. There is some risk & danger but it can work well if done carefully.

  • Like 2
Posted

Update and what looks like the solution:

It happened two times on the same board.
After the first time I trimmed the bad part off with the band saw and tried it again with less angle. In neither case did the bit hit the end of the board.

(The bit is a Craftsman 25454 cove & bead.)

What I think happened -- the larger boards had enough grain in both directions that I was going off the end grain toward the grain so there was nothing loose to grab. Like going around a circle on a larger piece of wood. This  problem was on the smallest of the three so there was nothing like the end grain starting point to physically absorb board's stress.

The curve on the shelves is the same but the difference is the size. That opened up the grain to being grabbed by the router bit.

Looks like the best solution will be to make the third, smaller shelf a large shelf then trim it down after the routing is done.

shelfsizes.jpg

Posted
13 hours ago, wdwerker said:

Clamp a piece of scrap against that edge for support. Climb cutting is another possibility. See if you can find a video or article about climb cutting. There is some risk & danger but it can work well if done carefully.

Gotcha. That would accomplish the same thing as building a larger unit then trimming it down.  Tx.

I read some on climb cutting last night -- hadn't heard the term before. Given the dangers I think I'll put that off for a while.

Looks like shelf 3 starts again from scratch next week.

Posted
2 hours ago, mat60 said:

I agree with Eric but didnt think he would like cats.;)

Not to sidetrack but I am a cat person (I know that's awfully girly of me).  They're cleaner and more interesting than dogs.  Don't have to let them out to poop.  They don't drool, bark or eat your shoes.  You can't win their friendship with food.  But they do piss in the house when they get mad at you for having a baby, which is why I no longer have cats...or dogs...or any other animals aside from the two kids...who do enough damage already.

I like dogs, but only big dogs and only when they're at someone else's house. LOL

Collin, if you're a little nervous about climb-cutting (which is not that dangerous in most cases if you know what you're doing)...you can try taking very light passes with a quality bit if you're forced to route against the grain.  I would start by chucking that Craftsman bit in the trash where it belongs and buying a Whiteside or a Freud.  Sharp is everything when it comes to routing...same as everything else.

  • Like 1
Posted

I agree with steve, use a sacrificial backer board to support the end of the cut. I usually have my piece a little wider than I need. Route the profile and go back on the table saw and remove about a 1/16 from all sides. Then route again. You'll have nice clean cut and no worry of chipout. 

 

-Ace-

Posted

So tonight I picked up another piece of wood just to get the process going again. Restlessness.

This piece worked just fine, like the first two.

 

And wife has been using Golden Pecan stain on oak around the house so she tried it on the poplar. Looks good and will be a suitable tone match with other things in the house

(As much as possible I eliminated the green parts of the poplar.) So don't just paint poplar.

 

The Craftsman bit remains sharp. I do wonder who's product they private labeled. It's not a bad unit , not like the stuff from HD.f891e2a7809429fa5ff95ec22222b579.jpg

 

Sent from my MotoE2(4G-LTE) using Tapatalk

 

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   4 Members, 0 Anonymous, 50 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined