Marmotjr Posted May 27, 2017 Report Posted May 27, 2017 For drilling into polypropylene / Nylon? I'm worried about heat build up in the forstners making the parts all gooey. I'm leaning towards spade. If anybody has any experience with this..... Quote
Eric. Posted May 27, 2017 Report Posted May 27, 2017 Forstner cuts cleaner. Slow the speed all the way down. Quote
wdwerker Posted May 27, 2017 Report Posted May 27, 2017 Spade bit would need to be razor sharp. Forstner or twist drill at the slowest speed & backed up or better yet sandwiched between to pieces of scrap wood . Stop often to clear shavings & let bit cool . I 2 Quote
Marmotjr Posted May 27, 2017 Author Report Posted May 27, 2017 I keep my drill press at it's lowest setting, and I'm not sure if it will be low enough. Tried to rip the 1" thick 12" long piece in half and this is what I got. Gonna kick over to the fewer tooth blade to see if that helps. But I'm not happy about trying to machine this stuff..... Quote
Tom King Posted May 28, 2017 Report Posted May 28, 2017 Some plastic is designed for machining. Why are you using this stuff? Quote
wdwerker Posted May 28, 2017 Report Posted May 28, 2017 Put it in the freezer ? Try the bandsaw on the lowest speed ? Or only raise the tablesaw blade 1/8 at a time and don't cut slowly. I'm just spitballing here. Quote
Marmotjr Posted May 28, 2017 Author Report Posted May 28, 2017 F*^& this S@#!. So yeah... that stuff that looks like a spiderweb in my TS? Nylon.... It should clean up easily enough, but this is not what I want to be doing. I'm just going to keep the other block for a cutting board if I need one (it's food safe). 27 minutes ago, Tom King said: Some plastic is designed for machining. Why are you using this stuff? Why? Because I thought this would make nice router table fence material, and I procured it from the scrap bin at work. We plane it flat with a 90" rotary planer, and then cut it on either a table saw or a CNC saw. Of course the TS uses a 14in blade, but I figured my TS would be able to handle it. So much for that idea. I'll just use that block of maple I have left over. Quote
Tom King Posted May 28, 2017 Report Posted May 28, 2017 How do the teeth on your blade compare to the teeth on the 14". If it cuts good on the other saw, I'd expect it's a tooth geometry difference, and not a size difference. I have an old Forrest Mr. Sawdust blade that does good on any plastic I've ever used with it. It has really weird, very sharp pointed teeth that don't look anything like any other woodworking blade. Quote
Marmotjr Posted May 28, 2017 Author Report Posted May 28, 2017 TBH, I hadn't looked at the tooth profile that closely. Quote
BonPacific Posted May 28, 2017 Report Posted May 28, 2017 Not sure how different they are, but I've had problems with Forstner bits when working UHMW. A very sharp screw-tipped spade bit cut wonderfully. Quote
TerryMcK Posted May 28, 2017 Report Posted May 28, 2017 I know that when drilling or sawing acrylic like plexiglass or polycarbonate sheeting like lexan I have had to buy a twist drills and saw blades with a specially manufactured cutting edge profile. The hook angle for saw blades is a negative angle http://www.trend-uk.com/en/UK/productlist/3/238/aluminium_&_plastics_sawblades.html to stop heat build up. For router bits again there is one type made especially for plastics http://www.trend-uk.com/en/UK/productlist/2/300/acrylic_cutters.html. I use these on plexi and they cut without leaving any residue or melt. No doubt there will be other manufacturers on your side of the pond too. For drills try these http://www.eplastics.com/plexiglass_lexan_plastic_drill_bits I've tried forstners and they melt their way through but leave residue around the hole and I've had some crack when they emerge from the other side. Not good. 1 Quote
Tom King Posted May 28, 2017 Report Posted May 28, 2017 I remembered that years ago the recommended way to cut plexiglas was to put a plywood blade (non carbide tipped if anyone has one of those these days) on backwards. Quote
Tpt life Posted May 28, 2017 Report Posted May 28, 2017 As a siding installer, I cut vinyl all day every day for years worth of days. The teeth backwards burns through and will gum up the side of the blade and the cut edge. Does not mean it is not the best way, just that even the best ways have a downside. Quote
kyokahn Posted May 30, 2017 Report Posted May 30, 2017 Assuming you're talking about soft (bendy) plastics like HDPE, PP, HDPE, UHMW and some Nylons... Forstner all the way, lowest speed. Spade bits need high speed to work and their thin profile doesn't help distribute the heat. Harder plastics like a Plexiglass can be a little more difficult for bigger holes. I'd actually recommend a hole saw for that, medium speed, but go slow and back out constantly. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.