Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

furnace vacuum for dust collection?

Featured Replies

Hello, I have been reading the forums here for a little while and am looking to get into the hobby after growing up in my grandfather's shop.

My first question for you all is about dust collection.  I hope to get to the point where i need a full size dust collector but for now I am using a Ridgid shop vac and a dust deputy.

I see a lot of people with this set up build a cart to keep them together. I fear that if i tried this it would be quite large with my 16gal vac.

I was just given a Mastercraft Sootmaster 652 ($700 new) which is much smaller at 6gal. I think it has the power, but know nothing about furnace vacs. Especially why they are so expensive! 

If anyone out there happens to know a thing or two about both DC and furnace vacs whould you be able to tell me if  a furnace vac with a dust deputy would be a decent set up while I relearn the trade?

A quick google search for that vac shows interesting specs. The "suction" it generates seems pretty powerful, at 90" of water lift, but the volume of air it moves seems rather low, at only 94 cubic feet per minute (CFM). For comparison, a 14 gal. Rigid wet/dry vacuum from Home Depot lists 168 CFM.

 

My guess is that this might not do all that well as a wood shop dust collector. A soot vacuum has a different sort of filtration system, as soot particles are extremely fine.

I used this for a long while until I bought a jointer and planer and it did a decent job. I use it now, only for my router table.

IMG_0385.thumb.JPG.dc240e5461a8e935d66d68edec7e75ce.JPG

 

That looks like a good quality vacuum, but it's not well suited for most woodworking machines. It would be fine for a  hand held sander or router, but the low CFM rules it out for just about anything else.

But even when you get a proper dust collection system, it's still good to have a smaller vacuum because the smaller tools need the higher pressure/low CFM than a dust collector can provide.

  • Author

Thank you all! I guess I should have gone with learning the basics first, just did not know where to start. I guess you don't know what you don't know. Working with my grandfather, his DC system was me vacuuming the shop after a project was done. Never considered looking at CFM. I guess I have a dedicated vacuum for my RO sander.

2 hours ago, Verbalkint99 said:

I guess I have a dedicated vacuum for my RO sander.

And it'll be perfect for that. You may need to rig up an adjustable bypass hole in the hose so you can vary the suctions. Too much can cause problems with scratches.

  • 2 weeks later...

 

I use a 16gal Ridgid shop vac with the dust deputy cyclone. Works well for saw, jointer, router, etc.

 

The planer I have is an old Delta with a 2 1/2" dust port. It's tough to get it all out. So I pulled the dust port lid off and let it fly. Seems the best way to keep it from binding up inside.

 

The collection hose is there to collect as much as possible.

I ditched the vac container altogether.  A small compartment large enough for the filter is all that is required if you run a Dust Deputy.  I clean the filter compartment about twice a year and get a couple of teaspoons of spoil out of the compartment.

Pardon the crude build but, this was version 1 which I designed as I went along.  I have not been driven to build version 2 . . . yet.

5730e8978adcd_DDafteruse(3).jpg.6f8c31b069d62b2784f3bc0e47a51b1a.jpg5730e896b3934_DDafteruse(2).jpg.89224b22a978ddf4ff78ad05d70550fe.jpg570da7d5c42b2_DDmod.jpg.803e599f02711d6f3ebea222381640e0.jpg

The vertical black "wands" are just stored.  The black hose connects the DD to the filter compartment.

1 hour ago, gee-dub said:

I ditched the vac container altogether.  A small compartment large enough for the filter is all that is required if you run a Dust Deputy.  I clean the filter compartment about twice a year and get a couple of teaspoons of spoil out of the compartment.

Pardon the crude build but, this was version 1 which I designed as I went along.  I have not been driven to build version 2 . . . yet.

 

The vertical black "wands" are just stored.  The black hose connects the DD to the filter compartment.

This is a project I've got on my list. There just doesn't seem to be any point to having that great huge barrel under the motor that is empty all the time. About the most it ever collects is a small hand full of dust.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.