Popular Post MisterDrow Posted June 19, 2017 Popular Post Report Posted June 19, 2017 I chose to spend the day woodworking today and (in addition to working on a shelving unit for our board games) made a magnetic bottle opener for fun! The initial glue up of scraps was done a couple weeks ago and I wasn't sure what to do with it then. It's alder, walnut, and maple. Time to turn the planer blades around... getting chip out no matter which way I run the board. Chamfered the edges on the front side. Drilled out and epoxied in a couple magnets to catch the bottle caps. Predrilled for the opener and started applying a couple coats of ARS. Works like a charm! It's going up on my new Etsy store for now. Hopefully someone wants it. These things are easy enough to make I could crank a few of them out in a day, no problem. 7 Quote
Coop Posted June 19, 2017 Report Posted June 19, 2017 So the magnet is on the back side? How thick is the wood from the front to the magnet? Did it really catch the cap or is that a photo op? Cool piece, regardless. 1 Quote
MisterDrow Posted June 19, 2017 Author Report Posted June 19, 2017 So the magnet is on the back side? How thick is the wood from the front to the magnet? Did it really catch the cap or is that a photo op? Cool piece, regardless. It actually catches the cap. It's drilled out on the back. The wood is just over 3/4" thick. There's about 1/8" of wood left between the magnet and the front. Bought some neodymium magnets off of Amazon and used them. They've got 17lbs of pull at the surface of the magnet so they're pretty strong. 1 Quote
Marmotjr Posted June 19, 2017 Report Posted June 19, 2017 Oooooh, A Cleveland Browns Bottle Opener! More useful than the actual Browns I must say. 2 Quote
wdwerker Posted June 20, 2017 Report Posted June 20, 2017 After 1/8 distance the pull force would be reduced to about 3 lbs from 17. Still plenty to grab a falling cap. And not so strong that it would be a struggle to get the cap off the board to put it in the trash. K&J Magnetics has pull force graphs for strength vs distance. Strength falls off rapidly. At 5/16 distance it's down to 1.5 lbs, at a 1/2" it's below .5 lbs pull. Practice drilling for the magnet as close to the surface as you can (on scrap) before you drill the actual part. 1 Quote
MisterDrow Posted June 20, 2017 Author Report Posted June 20, 2017 I just keep drilling it a bit more and testing it until the cap was reliably grabbed each time. I had a stop set on the drill press so it didn't go deeper than I wanted it to. 1 Quote
MisterDrow Posted June 20, 2017 Author Report Posted June 20, 2017 That is very cool. Looks nice. Thanks! These little things are a great way to get rid of scrap. I made a couple small cheese boards, too. I wish the grain lined up better on the cheese boards but the result is to be expected with scraps, I guess. 2 Quote
mat60 Posted June 20, 2017 Report Posted June 20, 2017 Looks like pretty nice scrap to me. I have some cherry,maple and walnut scraps in the shop I think the cheese boards would make great gifts. What finish do you use on them? Quote
wdwerker Posted June 20, 2017 Report Posted June 20, 2017 I've got a stack of 5/4 African Mahogany scraps about a foot long you can have but the freight to Maine might be $$. Its a matter of what do I do with it and where would I keep it on top of could I find it or even remember I've got it ? 1 Quote
MisterDrow Posted June 20, 2017 Author Report Posted June 20, 2017 Looks like pretty nice scrap to me. I have some cherry,maple and walnut scraps in the shop I think the cheese boards would make great gifts. What finish do you use on them? It's an orange oil and beeswax combo. Could also use just plain old mineral oil. I've got a stack of 5/4 African Mahogany scraps about a foot long you can have but the freight to Maine might be $$. Its a matter of what do I do with it and where would I keep it on top of could I find it or even remember I've got it ? You're in Maine? 1 Quote
wdwerker Posted June 20, 2017 Report Posted June 20, 2017 Mat60 is in Maine. He was commenting on the size and quality of your scraps .... 2 Quote
Gixxerjoe04 Posted June 20, 2017 Report Posted June 20, 2017 Magnetic bottle openers are handy as hell, I use big magnets in mine so it'll hold enough for at least one night of drinking haha. 2 Quote
MisterDrow Posted June 20, 2017 Author Report Posted June 20, 2017 Magnetic bottle openers are handy as hell, I use big magnets in mine so it'll hold enough for at least one night of drinking haha. Which ones do you use? Quote
MisterDrow Posted June 20, 2017 Author Report Posted June 20, 2017 10 hours ago, wdwerker said: He was commenting on the size and quality of your scraps .... There's a joke in there somewhere, I know it. Quote
Gixxerjoe04 Posted June 20, 2017 Report Posted June 20, 2017 1.5x.25", getting apart two of them that get stuck together is damn near impossible, but they usually will hold enough magnets to where you'll end up knocking them off when you use the opener after awhile. 1 Quote
MisterDrow Posted June 20, 2017 Author Report Posted June 20, 2017 Very nice. Just get them from Amazon? I got a six pack of the 1.26"x1/8" ones and had to use two stuck together to get the pulling power I needed. Next time I'll order the 1/4" ones. Quote
wdwerker Posted June 20, 2017 Report Posted June 20, 2017 K& J magnetics has instructions on how to separate powerful magnets. You build a jig to do it. Lots of info on their website. http://www.kjmagnetics.com/blog.asp?p=separating-magnets Their prices are a bit higher but the quality and selection are the absolute best. A lot of the cheaper magnets out there are poorly plated, easier to crack and chip and not as powerful for the size. N42 rated are weaker, N52 are more powerful. 1 Quote
Adam Campbell Posted July 31, 2017 Report Posted July 31, 2017 Its really nice. You should be able to get yourself at least 1/16" from the front of the opener. I would also recommend using a metal washer to place on the back of the magnet before you epoxy. Will increase the strength of the magnet, by focusing the magnets strength more towards the front. To hold even more caps rout a path in the back and glue down 2-3 magnets equally spaced on a piece of metal and epoxy that in. That should hold a parties worth of caps. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.