Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Teak Finishing Question

Featured Replies

Building a towel rack for a bathroom.  As I don't work with Teak that often, I was curious what others are using for finish for that wood and that environment.

I'd prefer to not use lacquer if at all possible.  Was considering salad bowl finish.  Also concerned with oils rubbing off on the damp towels.

Thoughts?

Thanks in advance!

About twenty five years back I used a product by Deft call Defthane in my bathroom everything but parts around the sink were the kids and now grand kids always had it wet still look good.  I remember the can saying it was good for water skis, so there is that.  You used to be able to get it in rattle can too.

How about GF Enduro-var.

Teak hold up with out anything, right?  it just gets gray that way.

Once a salad bowl finish has dried/ cured nothing should rub off on the towels. Teak is dense and oily wood so use thin coats of anything and wipe off the excess after a few minutes. 

  • Author
34 minutes ago, Chet said:

About twenty five years back I used a product by Deft call Defthane in my bathroom everything but parts around the sink were the kids and now grand kids always had it wet still look good.  I remember the can saying it was good for water skis, so there is that.  You used to be able to get it in rattle can too.

How about GF Enduro-var.

Teak hold up with out anything, right?  it just gets gray that way.

The Enduro-var is a possibility.  Ultimately, just trying to stay away from the fumes on this one.  Is this an issue with Enduro-var?  I haven't used it before.

30 minutes ago, wdwerker said:

Once a salad bowl finish has dried/ cured nothing should rub off on the towels. Teak is dense and oily wood so use thin coats of anything and wipe off the excess after a few minutes. 

This was my thought as well but, wanted to reach out to the knowledge base here with more "Teak" experience than I have.

Wipe joints in teak with lacquer thinner before gluing to remove the oils. Then assemble pretty soon. The oil will migrate back to the surface after a while. Epoxy or something similar would be my recommendation.  Plantation grown teak is pretty but not as dense & oily. Old growth has closely packed growth rings.

  • Author
48 minutes ago, wdwerker said:

Wipe joints in teak with lacquer thinner before gluing to remove the oils. Then assemble pretty soon. The oil will migrate back to the surface after a while. Epoxy or something similar would be my recommendation.  Plantation grown teak is pretty but not as dense & oily. Old growth has closely packed growth rings.

Using epoxy for exactly that reason!  I didn't "clean" the surface on the M&T joints but, the glue up was fairly soon after the cutting.

47 minutes ago, Chet said:

Endruovar is water borne just like the High Performance it just has the amber look like varnish instead of the nothing look High Performance has.

And that's my concern.  Being a bathroom with damp towels hung on them, I'm nervous about using the WB finish.

Kev, maybe use epifanes, if I'm correct a lot of boat builders use on teak and a boat has to be a harsher environment then the bathroom, unless you and the misses are doing something you shouldn't mention here or anywhere.

  • Author
Just now, Woodenskye said:

Kev, maybe use epifanes, if I'm correct a lot of boat builders use on teak and a boat has to be a harsher environment then the bathroom, unless you and the misses are doing something you shouldn't mention here or anywhere.

I'll be honest, I didn't even consider epifanes..  It's such a thick finish..  I'm sure it would hold up just fine but, a bit too much "film" for my liking in this case.

What about a cutting board oil and beeswzx blend? Or like tried and true or what's that one polimerized wax finish comes in a green can?

Edit: Rubio Monocoat

Fresh cut is close enough.  

Great thing about an oil finish on teak you could mask off the wall, sand or scrub w an abrasive pad and wipe a fresh coat of oil on before your going to be away for a few days, Voila ready to use again for several years. Or leave it alone if you like the patina.

  • Author
18 minutes ago, Chestnut said:

What about a cutting board oil and beeswzx blend? Or like tried and true or what's that one polimerized wax finish comes in a green can?

Edit: Rubio Monocoat

Thought about (and have some) T&T - Just concerned with it coming off on damp towels.  Love it on the rocker!  Never comes off on dry butts, just not sure about damp towels.

7 minutes ago, wdwerker said:

Fresh cut is close enough.  

Great thing about an oil finish on teak you could mask off the wall, sand or scrub w an abrasive pad and wipe a fresh coat of oil on before your going to be away for a few days, Voila ready to use again for several years. Or leave it alone if you like the patina.

Agreed!  The repairability is awesome!  Only concerned with it coming off on damp towels.

Thin coat on teak with a few days to cure is all a salad bowl oil/ varnish needs. It's not gonna hurt a towel. I like the Watco salad bowl/ cutting board finish that comes in the little can. 

  • Author
6 minutes ago, wdwerker said:

Thin coat on teak with a few days to cure is all a salad bowl oil/ varnish needs. It's not gonna hurt a towel. I like the Watco salad bowl/ cutting board finish that comes in the little can. 

Yea, I have the GF stuff and been happy with it.  I wasn't concerned with it coming off on towels.  Just more curious if that was the best finish for this project.

Appreciate your time Steve!

I've  rinsed & wiped down cutting boards finished with it and never had the moisture affect the finish or the towel. Always glad to help......

I did a big picture frame with teak and finished it with the Tried and True Oil/Varnish blend.  I applied it a little too thick so it took several days to cure, but it looks great.  Doesn't look plastic, but obviously this isn't something that ever gets handled.

I remember not likeing oil on teak.It seemed to take forever to dry not sure if it was linseed or Tung. So we used shellac pure blonde fresh flakes  first we made everything real shiney then cut it back to a soft satin sheen.

Aj

I would not use solvent lacquer or a thin oil finish. Solvent lacquer will turn gummy and blush from damp towels. A thin oil that won't seal the wood will result in grain swell ( not sure about teak though, never built with it)  

I would use Enduro Var, no smell and a tough finish. REMEMBER NO FINISH IS WATER /MOISTURE PROOF.  Some just do better than others, taking longer to break down.

-Ace-

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.