houstonwoodworker Posted July 11, 2018 Report Posted July 11, 2018 Need some help please! I have this planer and it’s the one that has a fan and shoots the chips out. I had a dust collector hooked up and chips were everywhere except in the dust collector. I checked and the fan was working and so was the dust collector. Any idea why the chips were all over the place and not working properly? Thanks so much. Quote
..Kev Posted July 11, 2018 Report Posted July 11, 2018 There's just no way to ask this except to say, I know from experience.. Is the blast gate open? Quote
houstonwoodworker Posted July 11, 2018 Author Report Posted July 11, 2018 Haha. Yes the gate on the dust collector was open. I wish they was the problem! Quote
wdwerker Posted July 11, 2018 Report Posted July 11, 2018 Were extra gates besides the one to the planer open ? Have you checked the line for a clog of shavings ? 1 Quote
..Kev Posted July 11, 2018 Report Posted July 11, 2018 Steve beat me to it.. I'd be looking for a clog in the line somewhere.. Also, can the dust collector keep up with that planer? Quote
houstonwoodworker Posted July 11, 2018 Author Report Posted July 11, 2018 I’ll check the lines. The dust collector has never had a problem keeping up until tonight. Quote
RichardA Posted July 11, 2018 Report Posted July 11, 2018 I don't know if this is your problem. But something like what your saying happened to my 735. Have you opened the top to see if there are chips piling up inside the planer? If there are I had to replace all the plastic around the fan, because as the chips hit the plastic shrouds, it wears a hole in them and chips wind up everywhere. Check that out. 1 Quote
Chestnut Posted July 11, 2018 Report Posted July 11, 2018 Sounds like a clog somewhere. If it isn't in the lines i'd do what RichardA above said and check inside the planer. The 735s move a lot of air if the filter, or filter bag on the dc is cloged enough to limit flow but still flows enough to seem like it's working could cause this trouble. Quote
Fred Belanger Posted July 11, 2018 Report Posted July 11, 2018 If you run the planer without the DC connected, do the chips fly out of the fan or do they fly out of everywhere also? If you run the DC and turn off the planer, raise the knive pretty high, and you wiggle a little fine dust, does it get sucked up into the planer? Can you feel wind with your hand in the planer (unplugged and turned-off, of course ) Other than that, I'm at a loss but curious about how it turns out. Keep this post updated. Good luck Quote
wdwerker Posted July 11, 2018 Report Posted July 11, 2018 Over the years I've noticed some boards shavings just seem to tangle up into a clog more than others. Taking a lighter cut is one tactic to try. Quote
..Kev Posted July 11, 2018 Report Posted July 11, 2018 12 minutes ago, wdwerker said: Over the years I've noticed some boards shavings just seem to tangle up into a clog more than others. Taking a lighter cut is one tactic to try. Especially if they have those little grids in the intake on the dust collector! My Grizzly unit had that and it tended to clog up. Quote
houstonwoodworker Posted July 11, 2018 Author Report Posted July 11, 2018 Thanks to all. I will check it out tonight and report back Quote
Ron Swanson Jr. Posted July 11, 2018 Report Posted July 11, 2018 I Have this planer too,but haven't had an issue with DC. Can you see where the chips are coming from? Also, not sure if it's relavent but I don't power on my DC with this machine, I just let the fan blow the chips into the DC. Might be worth a try as you try to troubleshoot. And yes, I agree w everyone else in that it sounds like you have a clog somewhere. Quote
collinb Posted July 12, 2018 Report Posted July 12, 2018 When I got mine the shop vac collection wasn't powerful enough. It forced chips out any crack it could create with the increased pressure. I suspect even a 1HP system might struggle against the output of this unit. That's why I went to a passive collection system just for this planer. 1 Quote
houstonwoodworker Posted July 13, 2018 Author Report Posted July 13, 2018 Thanks to all. I looked inside planer and there was a clog so hopefully this will work. I think I took an aggressive pass and it couldn’t handle it. Thanks again. 2 Quote
RichardA Posted July 13, 2018 Report Posted July 13, 2018 1 hour ago, houstonwoodworker said: Thanks to all. I looked inside planer and there was a clog so hopefully this will work. I think I took an aggressive pass and it couldn’t handle it. Thanks again. If it fills up again, you undoubtly have a problem with the plastic shrouds. You can get the parts from ereplacement.com 2 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.