Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Something more durable than Arm-r-seal

Featured Replies

Hello,

I finished a walnut island top with 5 coats of Arm-r-seal semi-gloss and I’m not terribly impressed with the durability. The amount of scratches in the surface makes me sick to my stomach. It scratches so easily. Lightly sliding a plastic cup causes scratches. Is there anything more durable I could put on top of this or do I just keep recoating when it becomes unbearable to look at?

P.S I followed the directions and let it cure for 3 weeks before using.

Thanks 

Perhaps your expectations are too high. Semi gloss will show scratches much worse than a matte finish

  • Author

I was thinking that may be the issue as well. I have some satin. Is it too late to add a couple coats of satin on top?

Nope. Make sure to lightly sand the surface.

Something more durable would probably be a flooring product but will be more difficult to apply.

Applying 5 coats won't make the surface any more durable. General Finishes recommends 3 coats. Were you applying the ARS straight from the can and not wiping back? If so, that's a lot of build that has to dry.

3 weeks isn't a long time for "5" coats. I believe GF says 30 days for full cure at the recomended 3 coats, but a lot has to do with shop temp, etc.

My bet, the finish is still young and needs to dry. ARS is as tough as it get's and is plenty durable. 

 

-Ace-

Lightly sliding a plastic cup should not produce scratches in the finish. Sounds like it is not fully cured, for one reason or another. 

I made a coaster with just 2 coats ARS gloss that sits on my desk (3 coats ARS satin). Both have seen ceramic mugs and plates set and slid across them- hot, cold, light, heavy- as well as other typical desk usage and there are not any noticeable scratches on either. They also receive the abuse of a 1.5 year old ‘playing’ with the mouse, keyboard, a metal picture frame, and anything else she gets her hands on. 

  • Author
7 hours ago, AceHoleInOne said:

Applying 5 coats won't make the surface any more durable. General Finishes recommends 3 coats. Were you applying the ARS straight from the can and not wiping back? If so, that's a lot of build that has to dry.

3 weeks isn't a long time for "5" coats. I believe GF says 30 days for full cure at the recomended 3 coats, but a lot has to do with shop temp, etc.

My bet, the finish is still young and needs to dry. ARS is as tough as it get's and is plenty durable. 

 

-Ace-

I’ve been thinking about how long it’s acually been sitting in my house. It probably been more like 2 months since I finished it, and we’ve just started really using it and noticed scratches. I agree 5 coats probably is too much. I followed Mart Cremona’s YouTube video on how to apply the finish. So I put as many coats as he did, and did properly wipe it back after applying. The last two coats were very, very light. 

Give it another month to ensure curing and then put a cat of satin on to cover the scratches?

I always used floor finish, but I was also finishing the floors.  I see one island top that I did in 1991 fairly often, and it doesn't have a scratch on it, after hosting large crowds, multiple times every year since then.  Neither does the White Oak floor in that house.  That was done with Moisture Cure Urethane, which has every toxic solvent on the dangerous solvents chart in it, other than gasoline.

I'd save leftovers in 20 oz. soda bottles (don't remember seeing water bottles then) filled all the way to the top.  I'd finish woodwork with the bottle in one hand, and t-shirt material in the other.

Bona Traffic HD would be another good one these days, that's low VOC, but the trouble with floor finishes is smallest size is a gallon, and it's well over 100 bucks a gallon.  The Bona stuff is two part, and leftovers will last for a few years, but you have to be very careful measuring because the acctivator is pretty small for a gallon.  To apply to a floor, normally you just pour the activator in the jug, shake, and apply from the jug directly to the floor.  It's flooded on, and squeegeed around application that's quick, and easy, if you are fairly well co-ordinated, and know how.

I ran across some Rubio floor finish this past weekend that also looks promising, and claims to be easy to repair.  MCU  (also Traffic) is not easy to repair, but damage would require something like a hammer.

I've never put anything but floor finish on tables, and counters, but I have a lot of experience finishing floors.   Floor finish comes in multiple gloss types from like glass high gloss, to looks like nothing is on the wood (Bona Naturale-an acid cure 2-part).  It's what you see on anything from gym floors to hotel lobby floors.

 I use a pre -catalysed waterbourne- it has about a 1 year shelf life. There are also post cat finishes that you mix right before you spray it- it has an hour or 2 pot life. Most of these finishes are primarily sold to pro shops but some dealers will sell to knowledgeable amateurs.

15 hours ago, Low-and-slow said:

I’ve been thinking about how long it’s acually been sitting in my house. It probably been more like 2 months since I finished it, and we’ve just started really using it and noticed scratches. I agree 5 coats probably is too much. I followed Mart Cremona’s YouTube video on how to apply the finish. So I put as many coats as he did, and did properly wipe it back after applying. The last two coats were very, very light. 

Give it another month to ensure curing and then put a cat of satin on to cover the scratches?

 

Try waxing it first. The wax will help the eye to not see the small scratches, also the wax will provide slip, which helps aid the surface from more scratching.

-Ace-

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.