Ron Swanson Jr. Posted May 24 Report Posted May 24 On 5/24/2026 at 3:34 PM, gee-dub said: Here you go . . . saw blade rack pdf.pdf 516.67 kB · 2 downloads Thank you sir! PS Who is this that handsome bastard in your new profile pic? 1 Quote
Popular Post gee-dub Posted May 24 Popular Post Report Posted May 24 On 5/24/2026 at 1:45 PM, Ron Swanson Jr. said: Thank you sir! PS Who is this that handsome bastard in your new profile pic? LOML came across an old passport photo and it gave me a laugh so I used it. I'm 18. Yes, I used to have hair . . . a lot of hair . I'm on the left. Some folks are local football heroes. We were local rock stars. This is back when 200 teenagers could gather at a youth center, rock out, and no one started a fight or shot anybody 4 1 Quote
Von Posted May 24 Author Report Posted May 24 On 5/24/2026 at 10:49 AM, gee-dub said: P.s. You've got the same tablesaw blade holder I do. I think I made it back about 2003 from a plan in one of the wwing mags. I've toyed with other ideas and designs that show up in the trade rags but, it just keeps on keepin' on. Yep, and that timeframe sounds about right. I always found it a little tricky to attach to the wall since it's less than 16" wide and heavy. Now it has a cleat on the back :-) 1 Quote
Ron Swanson Jr. Posted May 24 Report Posted May 24 On 5/24/2026 at 4:24 PM, gee-dub said: LOML came across an old passport photo and it gave me a laugh so I used it. I'm 18. Yes, I used to have hair . . . a lot of hair . I'm on the left. Some folks are local football heroes. We were local rock stars. This is back when 200 teenagers could gather at a youth center, rock out, and no one started a fight or shot anybody This is the coolest photo I've seen in a long time! I think it needs a beautiful, curly maple frame my friend. 1 Quote
Popular Post Von Posted May 25 Author Popular Post Report Posted May 25 I used up my dowel stock to make a little army of French Clean hangers. This is about half of them. And then got all my clamps organized, pulling little ones out of nooks and crannies around the shop. Nice to have them all out where I can see them. 6 Quote
Popular Post fcschoenthal Posted May 25 Popular Post Report Posted May 25 That's some clamp wall. The great thing about cleats is that you can move them around when you figure out what your use the most. I think I've rearranged mine 3 times now. I also ended up putting all of my spring clamps attached sticking out on a vertical board (like a T). It saved me some horizonal room. The triangle brackets are definitely the way to go with the other clamps (bar, pipe, F & parallel). You can get so many more in a smaller space. 4 Quote
Popular Post Von Posted June 8 Author Popular Post Report Posted June 8 [Oops, this post was supposed to go in my workbench journal.] Flush cut my pegs and cleaned up the glue squeeze out from the long rails. I noticed a couple of the pegs broke below the surface so I applied a little wood putty to smooth things out. Started on the shelf. I'm sandwiching two pieces of plywood under and over a cleat to make a void I can fill with, e.g., sand bags if I decide I want more mass. Chance to break out the pinch rods. I added a 1/16 shim so I'd have a little play and also moved the rods around to find the tightest spot. The rod just moves right over to the table saw, without the shim, to set the fence and cut the shelf to width. For the shelf length, I used a tape measure since my rods are not long enough. Less fun but good enough. I cut the shelf to length (45") with the track saw. I cut the corners to fit around the legs with a Japanese pull saw and did a little shaving with a low-angle block plane where the plywood was too tight. Bottom of shelf fits. Top part and cleats to follow tomorrow. 7 Quote
Mark J Posted June 9 Report Posted June 9 You might be able to copy & paste this post to your workbench journal thread. 1 Quote
Popular Post Von Posted June 29 Author Popular Post Report Posted June 29 A few more tool holders made. Always feels good to get stuff a home and out of the way, especially stuff like this which was combining to take up a lot of space on various horizontal surfaces. The #8 plane joins its brethren. And my pull and flush cut saws also now have a home. And I guess my coping saws too, though I have no idea what my original intent was for the block they are hanging on. 6 Quote
Ron Swanson Jr. Posted June 29 Report Posted June 29 On 6/29/2026 at 10:51 AM, Von said: A few more tool holders made. Always feels good to get stuff a home and out of the way, especially stuff like this which was combining to take up a lot of space on various horizontal surfaces. The #8 plane joins its brethren. And my pull and flush cut saws also now have a home. And I guess my coping saws too, though I have no idea what my original intent was for the block they are hanging on. That's a sweet setup! Looks great!! 1 Quote
Popular Post gee-dub Posted July 1 Popular Post Report Posted July 1 Looking good. It is so convenient to have a place for things. My shop can go from a disaster to cleaned up in about 30 minutes no matter how much stuff I have out. The only things left laying around after picking up are the ones I don't have spots for yet 3 Quote
Popular Post Von Posted July 11 Author Popular Post Report Posted July 11 Getting a few things done around the shop before I start on the workbench top, which will consume all available space. My old bench is going into the shed as a "generally useful horizontal surface" so I'm patching the hole I made for my planning stop. I angled the sides and glued a plug into place. The plug stuck up a 1/2" or so above the surface so I took the opportunity to try out this powered plane I got a while back. First time I've used such a tool and found it was nice for knocking down material quickly. I did end up finishing with a jack plane as I was having a hard time leveling the plug without taking off surrounding material. I impulse bought this tool balancer on ebay a while back and like it. Unlike a bungee cord, it's provides a nice constant force and worked well for keeping power cords out of the way. And I made a top for this A/V cart I picked up a while ago. Rather than letting random luck decide what covers it, I'm going to try it out as a sharpening station. My metalworking bench had been serving as such, but it's getting crowded and I really like the idea of being about to sharpen without having to make room and get stuff out. 6 Quote
JustAnotherGuy Posted July 16 Report Posted July 16 This is the first I am seeing this here! This is great work! I am envious. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.