Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Von's shop tour and setup log

Featured Replies

  • Popular Post

Oh, you also asked about stops.  I usually use a MatchFit clamp in a groove and clamp down the work piece.  Sometimes the height of the clamp gets in the way, and then I use MatchFit flip stops (you can see a pile of them below the table) or the stop from the miter saw.MatchFitStop1.thumb.JPG.ab19dcfefc1c3c00f148476a5a1359a5.JPGMatchFitStop2.thumb.JPG.85544470d5634c007b67c23cc62950da.JPG

  • Replies 387
  • Views 75.3k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • Immortan D
    Immortan D

    Count me in... I have enough "nice to have" tools that I never use. Things like the Starrett trammel set:   I never used that thing, not once, and I had it for many years.

  • Finally got some shop time yesterday and make progress on the in feed table. A got a couple of clamps and also some adhesive silicon pad. Building on the advice from wtnhighlander and Mark J, I replac

  • I'm blaming gee-dub for this upgrade :-) More seriously, in making the urn I was doing a bunch of micro-tweaking of my router fence to dial in the rabbet on the top and remembered his recommendation o

Posted Images

  • Author
On 8/2/2025 at 6:21 PM, Beechwood Chip said:

Oh, you also asked about stops. 

Thank you! Doing something similar is on my list.

  • Author
  • Popular Post

I added a big drawer, cobbled together from scraps, to the table with my air compressor to hold my pneumatic brad nailer, stapler, and all the little doohickeys that go with them. Hopefully no more knocking my nailer off of the peg it was hanging on once I get it fixed.

PXL_20250805_154628899.thumb.jpg.69305ec5242d4d8868bc53fa141189fa.jpg

  • Popular Post

Always good to have like things gathered together.  Even if I have drawers that are not "perfect" at least I know everything involved is in there somewhere :).  Watch those ball-rollers.  I had an outfeed that used them and often had crushed fibers that only showed up once finish was applied.  They are fine as long as additional milling will occur to remove the damage.  I guess their contact area is just a little too focused for heavier material.

I try to never have drawers. After Years of hiding stuff, I figure if I can’t see it, probably not worth hanging onto..

  • Popular Post

This is one of the great things about forums; you get contrasting approaches.  Drawers keep things clean and organized for me.  Shelves allow a lot of disorganized "jam-n-cram" which doesn't work for me.  It is probably that if I am not forced ot place things certain places I make a mess :).  That doesn't mean I'm right and someone else is wrong, it just means we organize differently.  It's all good.  Take from other's experiences and practices what works for you and leave the rest.  It's a win-win.

On 8/6/2025 at 12:21 PM, BillyJack said:

I try to never have drawers. After Years of hiding stuff, I figure if I can’t see it, probably not worth hanging onto..

That's not me - I like drawers.  But when I was making a kitchen cabinet for my tenant he didn't want doors.  He said he needed to see everything.

  • Popular Post

If I can label a drawer, and keep the same things in it each time it closes, I can get behind it. If it starts collecting unrelated stuff, that’s not the drawer’s problem, but rather mine. That’s the first step in recognizing the problem is never the inanimate object. That makes drawers great for sandpaper supply, or some other thing that may come in bulk sets of many pieces. Too many tools don’t fit that category, so it’s likely best for most of us to not focus on a single organizational system. 

I have a combination of both but I wish I had more drawers and less cabinet space.  I can pretty much tell you what is in every drawer and on every shelf.

All my drawers was a collection from tge years. I just removed an upper cabinet in my shop. Same thing a collection from the years..

 

I won’t spend a lot time trying to make my shop cools, I need it operational without playing “The price is right” and figuring out what is behind door number 1.

 

IMG_1970.jpeg

  • Popular Post

This is nice

 

IMG_1972.jpeg

IMG_1971.jpeg

But this is a woodworkers drawers after a few years.

 

IMG_1973.jpeg

  • Author
  • Popular Post
On 8/6/2025 at 12:08 PM, gee-dub said:

Watch those ball-rollers.  I had an outfeed that used them and often had crushed fibers that only showed up once finish was applied.  They are fine as long as additional milling will occur to remove the damage.  I guess their contact area is just a little too focused for heavier material.

Thanks for the timely advice. As you correctly guessed, I just made a doohickey for my jaw stand with the ball-rollers. I tend to only use such stands for ripping larger rough lumber, but I will keep your advice in mind. Catching something coming out of the thickness planer would seem to be a place I would be tempted to use this that would be problematic.

PXL_20250806_151651885.thumb.jpg.f2b4706060ab41217f3c98a17e0f728f.jpg

 

  • Popular Post
On 8/6/2025 at 7:39 PM, wtnhighlander said:

@BillyJack, my entire shop looks like that drawer. I think the problem is mostly having too much stuff that I don't really need. Too bad so much of it made that one thing I did one time 5 years ago, sooooo much easier..... :lol:

+1

And I’m also too easily influenced by some of the gadgets that some of you on here have! :wacko:

  • Author
  • Popular Post

A weekend shop project was to make some big J-hooks for my ceiling track. They are 1/4" rod with 1/4"-20 thread on one end and the bent J shape you see below on the other. A barrel/coupling nut connects them to a t-bolt which rides in the track. All the J-hooks I've found in the hardware stores are much smaller. I wanted something larger so I could easily hold extension cords and the like without them getting stuck in the hook and so I could kinda toss the cord into the hook without having to get on a step stool. Rockler has some hooks like this as part of their ceiling track system, but they are 5/16" thread and my track is too small for 5/16" t-bolts, and this seemed easier and cheaper than making or buying a 1/4"-5/16" coupler.

PXL_20250810_160926629.thumb.jpg.894fc82288e2904a3bf5a6f29b591de7.jpg

My little 3 1/2" vise isn't strong enough to hold rod this big and keep it from spinning while I thread it. I tried adding some aluminum jaws and even cut a vertical slot into those jaws, but no luck. I also tried a hardwood block with a 1/4" hole and a bandsaw kerf clamped in my vise with no luck. What worked was vise grips. They marred up the surface badly, but so be it.

PXL_20250810_151316942.thumb.jpg.83fbaee5b493227172a8d2aeba9cb74a.jpg

For bending, I tried these tube benders from HF. I knew I was pushing it using a cheap tool past what it was intended for (rod vs tubes), but it worked well for the first hook and I was hopeful.

PXL_20250810_173329988.thumb.jpg.534f220cbd87e4df0a6cf47e2161bec3.jpg

But on hook 2 I hit the end of my luck.

PXL_20250810_173438499.thumb.jpg.020c7519945b02ea7bcb661ed0b9d2cb.jpg

So I finished the bending with the vise and vise grips (the aluminum jaws did come in useful for this). I made three hooks total which lets me bring an extension cord out over my bench easily. I also ran vacuum hose on the track. Initially, I'm happy as it's nice to be able to have all that up and out of the way. 

PXL_20250810_180334041.thumb.jpg.25cd32ae21729492caec1ddb55c4d4ea.jpg

I remember doing wire bending as a kid, although it was much smaller diameter. I drilled holes in a piece of wood and banged in steel posts. I was then able to bend around them similar to the HF bender. If you need to do some more, you make want to think about heating the rod up to bend it more like a blacksmith would. You could just heat the bending spot with a MAP torch since you wouldn't need to worry about annealing. 

Like I’ve said, I’ve tried to eliminate drawers and cans full of stuff that I’ll think I’ll need one day. I’ve got a whole container full of extricate stuff aim trying figure out how to ge5 rid of . Tired of storing it..

On 8/12/2025 at 1:58 PM, BillyJack said:

Like I’ve said, I’ve tried to eliminate drawers and cans full of stuff that I’ll think I’ll need one day. I’ve got a whole container full of extricate stuff aim trying figure out how to ge5 rid of . Tired of storing it..

Might be telling you things you already know but your city has a hazmat waste facility to take any half full cans of pretty much anything to. If you leave the lid off of poly and similar finishes it will eventually dry and you can throw it in the trash. 

  • 3 weeks later...
  • Author
  • Popular Post

I picked up a Wixley 550 DRO with remote readout and installed it on my DeWalt 735. The 550 really is intended for larger planers so someone following in my footsteps should consider the Wixey 510 as well.

The Wixey website shows an example install of the 550 on the left side of the 735, but I really wanted it on the right side because of how my shop is set up and I also wanted to avoid drilling any holes in my planer because ... I didn't want to.

As you will see in the photos below, I succeeded. I removed the OEM height gauge and used a bottom bolt from it to mount the Wixey bar and a hole for the OEM indicator to mount the sensor bracket (I did have to use a longer M4 bolt for this). This is only two bolts total but in practice it seems sufficient. If it turns out I need more support I will either drill the brackets to fit another bolt or add support to the top of the height screw (where the OEM height gauge attached).

PXL_20250828_140317874.thumb.jpg.e2f76b30442ec1e3fc4bdaf7d59c653e.jpg

The real challenge was the Wixey has everything going off to the left, which made it a tight fit between the gauge and the infeed table, especially for calibration. One has to make sure you mount the Wixey high enough you can get the planed calibration wood into the calibration doohickey while clearing the infeed table (mine just does barely).

PXL_20250828_142934747.thumb.jpg.3ff2fdb6e077bf5311c6dfb8d9fb7d55.jpg

I mounted the remote readout on the side of the 735 since that is where I tend to stand when I use the planer. It uses a stock bolt and I just had to expand the hole on the bracket a little. Again one bolt seems to suffice and I'll drill the bracket for another if needed. I have dead space under my planer (it sits on a 2x4" frame), so the extra cable gets tucked in there.

PXL_20250828_143248653.thumb.jpg.cf24131ae15507edb6cfc6a05ef59041.jpg

I won't go through calibration since that is covered well elsewhere (e.g.) but the process worked well and I am happy to field any questions.

  • Popular Post

I got the iGaging one over a year ago and never have had the time to mess with it. I bought the router lift version as well and needless to say, it's not installed either. 

  • Popular Post
On 8/6/2025 at 6:24 PM, Von said:

I just made a doohickey for my jaw stand with the ball-rollers.

The Jaw Stand was one of my better purchases.  It stores small and comes out when needed and has proven very useful.  I made this weird sort of torsion box support for it.JawStand(4).thumb.JPG.cfcadfa940d8dadcf746f4040a9b5c10.JPG

JawStand(3).thumb.JPG.bb0c6f7c359f1870354d2e1d0a9df236.JPG

JawStand(5).thumb.JPG.e9fbf061b5b348b36757ccbca521b247.JPG

I found it so useful I went back and bought the crank-adjustable version when it was on sale.

 

On 8/29/2025 at 3:18 PM, Von said:

I picked up a Wixley 550 DRO with remote readout and installed it on my DeWalt 735.

I started with the Wixey on my DW 734 planer.  The use of it became so integrated into how I did things I added a DRO to my floor planer later on.

G0453Z-DRO004.jpg.de56fdf6e23712868f3fdde1287af206.jpg

I would be handicapped without the planer or tablesaw DRO's and would replace them immediately if they should die.  Being inspired I tried one for the router table.  We all work differently but it added no value for me and I eventually removed it.  

A tool's value varies with what we do and how we do it.  After so many years of using them the DRO on the tablesaw and planer are built into how I think about how I will perform an operation now.

 

  • Author
On 8/31/2025 at 1:47 PM, gee-dub said:

The Jaw Stand was one of my better purchases.  It stores small and comes out when needed and has proven very useful.  I made this weird sort of torsion box support for it.

It was your praise of the Jaw Stand in a prior post that nudged me to jump on it when I saw it on Craigslist and I agree on its usefulness. I've used it to hold a door while planing it and surprisingly, with the 2"x6" board, it makes a great auxiliary table around the shop for small work, keeping stuff off my main bench. No horizontal space goes to waste.

Do you find your torsion box support suffices for material infeed/outfeed support? I've been thinking I need a roller stand but I see how the angled top like you have could suffice?

On 8/31/2025 at 1:47 PM, gee-dub said:

I would be handicapped without the planer or tablesaw DRO's and would replace them immediately if they should die.  Being inspired I tried one for the router table.  We all work differently but it added no value for me and I eventually removed it.  

I'm tempted to get a DRO for my drill press. The use cases are mortises with Forstner bits and stoping just short of drilling through holes and risking blow out. My drill press has a mechanical depth stop, but I find it's challenging to set accurately and precisely with only two hands.

I just sort of pulled the torsion box out of my ear.  I had seen others use tapered, sanded, finished, and waxed "rails" in a vise or clamped to a stand and that was the impetus.  I use it for all sorts of things and that definitely includes outfeed support.  The slightly rounded top allows sagging outfeed items to climb up on it.  Standing lengthwise it does not tend to tip like some supports can.  It is great for long plywood pieces that hang off the side of the tablesaw during feed, ergo the length of the thing.  For storage I just turn it parallel to the vertical post and slide it down even with the folded legs.

 

Jaw Stand (6).jpg

Jaw Stand (7).jpg

My DP has the type of depth stop you can use setup blocks on to set the range.  I can certainly see a DRO being helpful on a DP for stopped holes, mortises and so forth.  I'll bet there's more than one person on here who gets a benefit of a DRO on the router table, it just didn't turn out to be useful for me.

  • Popular Post
On 9/1/2025 at 6:20 PM, gee-dub said:

I'll bet there's more than one person on here who gets a benefit of a DRO on the router table, it just didn't turn out to be useful for me.

I just figured that it would be easier looking at the display than trying to squint to see the right line on the ruler.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.