Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Von's shop tour and setup log

Featured Replies

On 5/21/2025 at 9:23 AM, Mark J said:

@Beechwood Chip, if the miter is less the SCM throw, say 10", and if you can get some clamps on the workpiece for hands free holding, you could miter on a SCM.

I thought of that.  I guess it depends on what you consider a long miter.

  • Replies 387
  • Views 75.3k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • Immortan D
    Immortan D

    Count me in... I have enough "nice to have" tools that I never use. Things like the Starrett trammel set:   I never used that thing, not once, and I had it for many years.

  • Finally got some shop time yesterday and make progress on the in feed table. A got a couple of clamps and also some adhesive silicon pad. Building on the advice from wtnhighlander and Mark J, I replac

  • I'm blaming gee-dub for this upgrade :-) More seriously, in making the urn I was doing a bunch of micro-tweaking of my router fence to dial in the rabbet on the top and remembered his recommendation o

Posted Images

I can't remember if you have a track saw or not, but that could be an option if you do.

Here's an example of a 45* sled for the table saw that could work:

 

That sled looks like a good solution, but I'm guessing it is a little complex to build.

I think you could simplify it with just the 45* platform and a miter bar if you just need it once.

On 5/21/2025 at 9:57 AM, Mark J said:

That sled looks like a good solution, but I'm guessing it is a little complex to build.

Not in the least. I made Kev’s example and as long as the two fences are set up at 90*, the two cuts will come out perfect. 

  • Author
On 5/21/2025 at 8:59 AM, Beechwood Chip said:

How do you do long miters on a Kapex?

On 5/21/2025 at 9:23 AM, Mark J said:

@Von, how long a piece are you trying to miter?

@Beechwood Chip, if the miter is less the SCM throw, say 10", and if you can get some clamps on the workpiece for hands free holding, you could miter on a SCM.

Correct, these box sides are ~7" tall, so I tilt the SCM head to 45 degrees R or L, clamp the piece so the grain is running the length of the SCM bed and cut one end after the other. I batch the first and second cuts and set a stop on the second cuts so all my pieces are the same length.

It works well, it's just a SCM beveled to 45 and doing a long cut is a lot of saw blade exposed and moving around and not my favorite thing to do.

On 5/21/2025 at 10:02 AM, Beechwood Chip said:

I thought of that.  I guess it depends on what you consider a long miter.

I guess long in this case is more than I could do with the piece vertically on the SCM.

  • Author
On 5/21/2025 at 10:45 AM, legenddc said:

I can't remember if you have a track saw or not, but that could be an option if you do.

Here's an example of a 45* sled for the table saw that could work:

I need my sides to be the same length. How would one cut to a repeatable length with this sled?

I forgot to say in my first reply, thanks for all the input all!

@Von, with this sled, I cut one end of all the pieces on one side of the sled. Then with the adjustable stop blocks that are made onto the sled, I cut the other end of the pieces on the other side of the sled, thus guaranteeing a 90* angle and that all sides are equal length. And if your pieces exceed these blocks, you can clamp or screw longer strips to the fences. 

  • Author
On 5/21/2025 at 9:27 PM, Coop said:

@Von, with this sled, I cut one end of all the pieces on one side of the sled. Then with the adjustable stop blocks that are made onto the sled, I cut the other end of the pieces on the other side of the sled, thus guaranteeing a 90* angle and that all sides are equal length. And if your pieces exceed these blocks, you can clamp or screw longer strips to the fences. 

Sorry, I'm not following. Just to make sure we're talking about the same thing, I think we talking about the jig in the image below (taken from the video)? If so, I don't understand how you are cutting on two ends of it - seems like one can only cut on the bottom end by the blade. Thanks.

sled.jpg.b82d4b0b8c4840e9121ecb1b5246ce5f.jpg

Sorry. I was referring to the “picture frame sled”.

OK, I think there are two dimensions we're talking about.  There's the height of the box, which is where we're cutting the miter, and then there's the width or length of the box, which would be sticking up at a 45 degree angle above the table saw.

Both would first be cut to the appropriate size on the table saw or miter saw with 90 degree cuts.

The trick then is to cut the miters using the jig without changing the length of the boards.  I'd cut the boards a little long initially, miter one end on the jig, and then use the jig to shave off the other end until you get a perfect fit.

[EDIT] I guess if you don't want to creep up on the fit, you could add a 45 degree stop block to the jig opposite the angled support, so that a board would be secured on both sides of the blade so that the kerf met the corner perfectly and didn't shorten the board at all.  Then all of your cuts would be repeatable. 

  • Author
On 5/21/2025 at 10:08 PM, Beechwood Chip said:

The trick then is to cut the miters using the jig without changing the length of the boards.  I'd cut the boards a little long initially, miter one end on the jig, and then use the jig to shave off the other end until you get a perfect fit.

[EDIT] I guess if you don't want to creep up on the fit, you could add a 45 degree stop block to the jig opposite the angled support, so that a board would be secured on both sides of the blade so that the kerf met the corner perfectly and didn't shorten the board at all.  Then all of your cuts would be repeatable. 

Something like this? (Please ignore all the minor alignment errors.)

wto.thumb.jpg.e9b46d88efcd5c7acf766ea25546e48d.jpg

I was thinking that the bottom stop would have a 45 bevel, so that it would work for any thickness stock.  And I don't think you need the top stop; you position the stock against the bottom stop and go.  

My idea is that you've already cut the stock to length at the miter saw with a stop, and now you just need to cut the miters in a repeatable way.  If you cut all the stock the same way, then they should all end up the same size, even if cutting the miters does take a hair off the length.

[EDIT] hold on, I just thought of a problem with my plan!  The off cut will be trapped between the stop and the blade and gravity will drop it onto the blade causing kickback.

[EDIT 2 ] Maybe a separate 45 degree stop (like the jig, but smaller and not attached).  You hold the stock against the jig and use the "stop" to make sure that the bottom corner of the stock is aligned with the edge of the kerf.  Then, clamp down the stock to the jig, remove the alignment stop, and cut your miter.  I'll see if I can make a diagram like yours - it really helped!

Here's my idea.  The bottom stop (alignment tool) keeps the stock from falling into the kerf on the sled, so the corner of the stock is lined up with the corner of the jig which is lined up with the edge of the kerf.

In case it's not obvious, I'm just spit-balling here.

miter jig.jpg

Forgive me for going off the reservation here but have you considered a chamfer bit in a router table? assuming you have one that is.

On 5/22/2025 at 11:57 AM, Chet said:

This is a great video showing how to cut carcase or long miters on the table saw.  About 30 minutes long but worth a look.

https://woodschool.org/woodschool_videos/31-how-to-cut-carcase-miters/

The video shows tilting the saw blade, and Von's problem is that his saw gets wonky if he tilts the blade, so he wants to leave it at 90.

  • Popular Post

@Beechwood Chip, I like your last diagram, but would want the leading edge of the stock clamped to the jig, so it doesn't drop into the spinning blade as the cut is completed. For the same reason, this jig design should not be drawn back over the blade until the stock is removed.

  • Author
On 5/22/2025 at 8:46 AM, Beechwood Chip said:

Here's my idea.  The bottom stop (alignment tool) keeps the stock from falling into the kerf on the sled, so the corner of the stock is lined up with the corner of the jig which is lined up with the edge of the kerf.

On 5/22/2025 at 7:52 PM, wtnhighlander said:

@Beechwood Chip, I like your last diagram, but would want the leading edge of the stock clamped to the jig, so it doesn't drop into the spinning blade as the cut is completed. For the same reason, this jig design should not be drawn back over the blade until the stock is removed.

Thanks for all the suggestions and thoughts. You are confirming for me this (a repeatable long 45 miter to length) would be a tricky cut with a number of facets to work out. I think it could be done, but...

On 5/22/2025 at 11:54 AM, Ron Swanson Jr. said:

Forgive me for going off the reservation here but have you considered a chamfer bit in a router table? assuming you have one that is.

Yes, that's actually my current plan for what to try next. I'll make a coping-style sled with a stop so I can get a repeatable length.

And another thought just occurred to me - has anyone tried doing a long miter cut on a bandsaw by tilting the table? 

Again, thanks all. I'll report back...

On 5/22/2025 at 7:52 PM, wtnhighlander said:

@Beechwood Chip, I like your last diagram, but would want the leading edge of the stock clamped to the jig, so it doesn't drop into the spinning blade as the cut is completed. For the same reason, this jig design should not be drawn back over the blade until the stock is removed.

Agreed!  Maybe use the alignment block to position the stock, clamp the stock to the jig, remove the alignment block, and then when you make the cut the offcut will fall away from the blade into the space where the alignment block was.

 

On 5/22/2025 at 8:02 PM, Von said:

And another thought just occurred to me - has anyone tried doing a long miter cut on a bandsaw by tilting the table?

My first thought was that I'd run the piece through the jointer afterwards to clean up the bandsaw cut, and then I remembered that jointers usually have a way to tilt the fence to make angled edges.  So, if you have a jointer, that's a way to do it.

@Von, excuse me if I missed it but how wide is the board that you need the ends mitered? 

  • Author
On 5/22/2025 at 10:15 PM, Coop said:

@Von, excuse me if I missed it but how wide is the board that you need the ends mitered? 

The box is roughly 10" x 7" x 6" high, so I've got 10"x6" and 7"x6" boards with the miters on the 6" portions of both.

13 hours ago, Von said:

I'll make a coping-style sled with a stop so I can get a repeatable length.

And another thought just occurred to me - has anyone tried doing a long miter cut on a bandsaw by tilting the table? 

With the router table & coping sled you will probably have to remove stock a little at a time in multiple passes.  Each time you raise the router bit you will also be making the board shorter.  So I think the only way to make two boards exactly the same length is to send them through the router at the same time with the same bit height.  So make the coping sled big enough for two boards?

Also, we are assuming that the angle on a 45* chamfer bit is accurate enough for a miter joint.

I think it would be difficult to tilt a BS table accurately enough to get a good miter joint.  Also, in my limited experience the cut surface can have a lot of saw marks which might interfere with the glue bond.

I was also thinking the jointer was the way to go, too.  But then I remembered, Von just sold his bench top jointer.

Von, have you considered using a box joint instead?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.