Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Von's shop tour and setup log

Featured Replies

On 7/20/2025 at 3:15 PM, Von said:

Put up the second of the two rails I found at Restore on my ceiling. This one at an angle from the corner where I usually keep my shop vac cart to my workbench.

These rails are 7' long and have 1/4" t-track in the bottom. I use t-track bolts with barrel nuts and an eye- or J-bolt to make mobile hangers. I put the first up over my workbench to try it out and it's been effective for power cords, dust collection hoses and holding up random work pieces. I decided I wanted the second one dedicated for holding up the hose to the shop vac and a power cord that switches it on.

PXL_20250720_145644004.jpg

That's pretty cool @Von. Anything that keeps hoses, cords and whatever else offv the bench and floor is a winner in my book. 

  • Replies 387
  • Views 75.3k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • Immortan D
    Immortan D

    Count me in... I have enough "nice to have" tools that I never use. Things like the Starrett trammel set:   I never used that thing, not once, and I had it for many years.

  • Finally got some shop time yesterday and make progress on the in feed table. A got a couple of clamps and also some adhesive silicon pad. Building on the advice from wtnhighlander and Mark J, I replac

  • I'm blaming gee-dub for this upgrade :-) More seriously, in making the urn I was doing a bunch of micro-tweaking of my router fence to dial in the rabbet on the top and remembered his recommendation o

Posted Images

  • Author
  • Popular Post

I got tired of having no go place to store my Matchfit push blocks, I broke down and took a few minutes to make and mount a holder on the side of my table saw cabinet.

PXL_20250721_174946321.thumb.jpg.932f1949d446f53105884937d74a332b.jpg

Then back to my project to make my actual wood working project, I built a vertical jig for my table saw to cut the bevels on my box lids. Letting the glue firm up overnight and will take it for a spin tomorrow.

PXL_20250721_200245803.thumb.jpg.2db40eb4355504a4d979e48474aeab3d.jpg

PXL_20250721_200240306.thumb.jpg.7afdb688088969fc027919962661a98b.jpg

  • Popular Post
On 7/21/2025 at 5:21 PM, Von said:

I got tired of having no go place to store my Matchfit push blocks, I broke down and took a few minutes to make and mount a holder on the side of my table saw cabinet.

PXL_20250721_174946321.thumb.jpg.932f1949d446f53105884937d74a332b.jpg

Then back to my project to make my actual wood working project, I built a vertical jig for my table saw to cut the bevels on my box lids. Letting the glue firm up overnight and will take it for a spin tomorrow.

PXL_20250721_200245803.thumb.jpg.2db40eb4355504a4d979e48474aeab3d.jpg

PXL_20250721_200240306.thumb.jpg.7afdb688088969fc027919962661a98b.jpg

Looks good! It's supremely satisfying to finally have a place for long time feral tools. 

On 7/21/2025 at 6:21 PM, Von said:

I got tired of having no go place to store my Matchfit push blocks, I broke down and took a few minutes to make and mount a holder on the side of my table saw cabinet.

PXL_20250721_174946321.thumb.jpg.932f1949d446f53105884937d74a332b.jpg

My Grrrippers have a home, but it sucks.  I'm going to steal your design.

  • Author
On 7/21/2025 at 7:56 PM, wtnhighlander said:

Forget the grippers, the handle on your jig is awesome!

Thanks. It's been kicking around my shop on various jigs for so long I've forgotten where I got it from.

On 7/21/2025 at 7:56 PM, wtnhighlander said:

Did you build in any way to adjust it for being square to the table? I made a similar 'saddle on the fence' style jig a while back, and have found it difficult to keep truly vertical.

Hmmm. No. What I'm used to doing is using blue tape or shims between a vertical fence and my table saw fence to adjust it to vertical. This one went together square. If it toes in I can use blue tape on the inside of the bottom to force it back square. If it toes out... I think I'm out of luck? I'd have to think about it.

I'm curious how yours racked?

On 7/21/2025 at 8:01 PM, Von said:

If it toes out... I think I'm out of luck?

If it goes out, put the tape on the top of the right side of your fence.

On 7/21/2025 at 7:56 PM, wtnhighlander said:

Did you build in any way to adjust it for being square to the table? I made a similar 'saddle on the fence' style jig a while back, and have found it difficult to keep truly vertical.

Maybe make the horizontal wider and put braces above the horizontal for the tall fence and below the horizontal for the outside leg.  If you build the two legs the same length, and slide the legs along the table, then as long as the legs are the same length and everything is square, then the tall fence will be perpendicular to the table.

It's past my bedtime, so I might not be making sense.

On 7/22/2025 at 6:44 AM, wtnhighlander said:

Mine rides the fence, the lower edges don't rest in the table.

That makes sense.  In that case the goal is to make the tall fence register against the side of the fence.  So, build it so that everything is square and won't flex, and add enough tape to the outer leg to assure that the tall fence is pressed against fence from top to bottom and side to side.  If you wanted to, you could add screws to micro adjust the fit,

Is your fence square to the table, and does it wobble?  The tall fence is putting a lot more leverage on it, and it seems like fences would be designed to stay parallel to the blade and miter slots, not so much perpendicular to the table.  If your fence is not reliable, then registering to the table with sliding legs may be your best bet.

  • Author
On 7/22/2025 at 6:44 AM, wtnhighlander said:

Mine rides the fence, the lower edges don't rest in the table. The idea was that miter bar slots, and the webbed side wings of my saw top, would cause trouble, but so does rocking on top of the narrow fence.

Ditto.

  • Author
On 7/21/2025 at 7:32 PM, Beechwood Chip said:

My Grrrippers have a home, but it sucks.  I'm going to steal your design.

I have 2 1/8" between the dowel and the wall and that's too tight (I'm spending some quality time with a rasp this morning). Do at least 2 1/4". I'd do 2 1/2" if space is not an issue (I'm minimizing how much mine stick out into my walkway).

  • Author
  • Popular Post

With the glue dry I removed the wax paper protecting my fence and the fit for the jig was just a bit loose, so I added some blue tape (2-3 pieces per side) to snug things up and give me just a hair of resistance when pushing.

PXL_20250722_143039599.thumb.jpg.ee37c9ee2b24d71485fe9a0a67f178bf.jpg

Then something close to actual woodworking. I got my box tops cut to size (I'm making two to see which I like better) and found all the bits and pieces to mount them to the jig. At that point, time was running short due to an appointment, so I'll be back at it tomorrow.

PXL_20250722_151913987.thumb.jpg.00b28f646ae0e55662c4188d4621f059.jpg

  • Popular Post

@Beechwood Chip, my fence is solid, just not very wide. Aluminum extrusion type. To allow the jig to slide on it requires enough 'slop' that just a little pressure on the upper part of the jig will make it shift.  I'm planning to switch to a jig that rests on the table and is guided by the miter slot, not the fence.

  • Author
On 7/22/2025 at 7:35 PM, wtnhighlander said:

@Beechwood Chip, my fence is solid, just not very wide. Aluminum extrusion type. To allow the jig to slide on it requires enough 'slop' that just a little pressure on the upper part of the jig will make it shift.  I'm planning to switch to a jig that rests on the table and is guided by the miter slot, not the fence.

An alternative design I looked at is the one in this video. It has a foundation that rests on the OEM fence and doesn't slide. This might be useful in your case because you could clamp it down firmly instead of relying on friction.

On 7/23/2025 at 7:21 AM, Von said:

An alternative design I looked at is the one in this video.

I follow Matt and have looked at this fence several times. It's on my to-do list, but will probably have to wait until I really need it before attempting.

  • Author
  • Popular Post

Here's my final jig configuration. My hold down isn't strong enough and the work piece kept getting pushed up by the saw blade, hence the stop above the work piece. I also added a piece of 3/8" ply under the hold down so it wasn't so finicky about the groove. I should add a wing nut or a knurled nut on the bolt under the hold down so I can loosen the hole down without loosening the plywood. All together, I'm very happy with this. And, unrelated to this jig, the recently acquired micro-adjuster on the router table was a huge help in routing the lip on the bottom of the top to fit the box - I should have bought one of those years ago.

PXL_20250725_141656469.thumb.jpg.5a6d0405495ad2f9f2ee8d26f302fcc7.jpg

14 hours ago, Von said:

the recently acquired micro-adjuster on the router table was a huge help

Remind me.  What did you do here?

  • Author
On 7/26/2025 at 7:59 AM, Mark J said:

Remind me.  What did you do here?

Rockler's router fence micro-adjuster - here's my original post.

  • Author

On my last project I ran into the drill press arms running into the fence problem again. I recall gee-dub replacing his arms with shorter ones (sorry, I can't find the thread), so I took my arms off to figure out what it would take to replace them and realized the arms are 3/8" rods threaded on both ends. I figured I could do that, so I bought some 3/8" rod, cut a short piece, cleaned up and chamfered the ends and threaded them. 3/8" rod is probably the largest thing I've threaded and that bit was by far the hardest as my vise had a very hard time holding the rod against the torque of the die and the rod kept spinning and slipping on me. But I made it through and ended up with a handle about 1 1/4" shorter. I'll try this out for a while and decide if I want to tweak the length before making a couple more. I think some aluminum jaws for my vise are worth a try for a better grip. I have rubber jaws and they slipped much worse than the hard jaws. BTW, I ended up with new knobs as I thought at first the OEM knows were affixed to the handles, but turns out they were just firmed screwed on, so I could have reused them.

PXL_20250731_144044773.thumb.jpg.82787ec2a0bede0e60e74ad8c71b2467.jpg

PXL_20250731_144134112.thumb.jpg.a861530d933ec917d53bd1a0f91cb079.jpg

 

As an alternative, could one shorten the fence so that it does not come into contact with the drill press arms?  (I haven't had occasion to use a fence on my drill press).

I’ve put a strip of 3/4” material between my fence and workpiece to set the fence back enough that the arms won’t make contact. 

  • Author

Thanks all for the feedback and alternate approaches.

On 8/1/2025 at 10:00 AM, Mark J said:

As an alternative, could one shorten the fence so that it does not come into contact with the drill press arms?  (I haven't had occasion to use a fence on my drill press).

Yes. I've seen a lot of drill press fences that have shorter fences on the right and that's probably the easier way to address this. I admit I have to do some threaded rod work for something else and so I was biased to my approach.

I think fences on drill presses are largely optional. Mostly I like the idiot proofing when I have to drill multiple holes the same distance from an edge. Every blue moon I'll drill some mortises with forstner bits when I can't use my router for some reason and then I really like the repeatability a fence gives me.

On 8/1/2025 at 11:25 AM, Beechwood Chip said:

I don't have a fence on my drill press.  I have MatchFit slots in the table, and use various clamps or stops as necessary.  I thought I'd mount a fence in the slots, but it never became necessary. 

I welcome some photos of your table (or a pointer if you've already posted them). My table may be old enough to drink at this point and making a new one is on my someday list. I have not come across a Matchfit version, so I'd like to see how you did it (and if you have any stops you find particularly useful).

On 8/1/2025 at 11:31 AM, Coop said:

I’ve put a strip of 3/4” material between my fence and workpiece to set the fence back enough that the arms won’t make contact. 

If I understand you, I think your drill press has more room between the quill and the pillar than my benchtop Delta. My fence can't go back far enough because of the pillar such that it can get past the swing of the arms so that going back helps with clearance. 

Again, thanks all.

  • Popular Post
On 8/1/2025 at 4:15 PM, Von said:

I welcome some photos of your table (or a pointer if you've already posted them). My table may be old enough to drink at this point and making a new one is on my someday list. I have not come across a Matchfit version, so I'd like to see how you did it (and if you have any stops you find particularly useful).

I cut a grid of MatchFit grooves, with one horizontal and one vertical groove centered on the drill bit.  I cut an off-center square recess for an insert, so that I could rotate or flip the insert to get a fresh section.  I have a stack of inserts pre-made.  I made a mount for a "StayPut" hose that has a MatchFit runner so I can position it where I want.  It works well enough.

My mistake was to position one of the grooves too close to the recess, and the strip of MDF between them broke off.  It might have worked if I had used solid wood instead of MDF, but if I re-do it I'd still use MDF and just check my layout more carefully.

[EDIT one year later: The MDF squares popped off when I cranked down on the MatchFit clamps.  And the dust collection was annoying to set up.  The StayPut hose could only be positioned loosely, and it really needed a nozzle to pick up the waste.  I'm rebuilding it with plywood, keeping the grooves at least 1.5" from the insert.  I'm also going to mount the dust collection on the drill press column with a pivoting elbow to position the nozzle.] 

IMG_1243.JPG

Edited by Beechwood Chip
Wanted to explain design mistakes

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.