Popular Post Von Posted September 8, 2025 Author Popular Post Report Posted September 8, 2025 I did finish replacing the handles on my drill press with shorter (by about 1.5") versions. Same process as first handle, threading both ends of. a 3/8" rod and adding a hardware store handle. Used it a bit, so far no issues. 5 Quote
Popular Post Von Posted September 10, 2025 Author Popular Post Report Posted September 10, 2025 I copied Chip's bandsaw dust collection using the Grizzly Dust Deflector. To deal with Grizzly thinking that 2" is a standard dust collection port size, I found a 2 1/2" -> 2 1/4" adaptor on their site, which got me most of the way to adapting to my 2 1/2" hose. A few wraps of duct table handled the transition from the deflector to the 2 1/4" side of the adaptor. This semi-stiff 2 1/2" hose was kinda a pain to get a hose clamp on, but it handled all the turns fairly well (and got my order large enough for free shipping). I have a shop vac on this side of my shop, so I adapt the main 4" dust collection port from the bandsaw down to 2 1/2" and then use a y-adaptor to merge the two into my shop vac. So far so good. The little bit of dust you see is from some fairly serious cutting with the new set up and is about a 75% reduction from what it was (sorry, I forgot to take a "before" photo). One annoyance is Grizzly skimped on the glue for the magnets in the deflector, so two quickly came out (and had me wondering why the deflector was flopping around) and had to be superglued back. 5 Quote
fcschoenthal Posted September 10, 2025 Report Posted September 10, 2025 That's a nice solution for the Grizzly. I'll have to look into it, after you get some time with it to give it a thorough workout. I never did find a good 3D print version. 1 Quote
Popular Post Beechwood Chip Posted September 10, 2025 Popular Post Report Posted September 10, 2025 Yesterday I used my bandsaw to round off the corners of a board, and tried to nudge the offcut away from the blade for the next cut. The offcut seemed stuck in place somehow. Then I realized that it was the suction from the dust collector. I was surprised because I have about 30' of 4" PVC between the dust collector and the bandsaw, and then 4" goes to the lower DC port and 2 1/2" flex goes to the upper "Dust Deflector". I wasn't expecting to get shopvac like suction above the table. 5 Quote
Beechwood Chip Posted September 10, 2025 Report Posted September 10, 2025 On 9/10/2025 at 4:06 PM, Von said: One annoyance is Grizzly skimped on the glue for the magnets in the deflector, so two quickly came out and had to be superglued back. Hah, same thing happened to me! I had to re-glue two magnets. 1 Quote
Popular Post Mark J Posted September 11, 2025 Popular Post Report Posted September 11, 2025 16 hours ago, Von said: One annoyance is Grizzly skimped on the glue for the magnets in the deflector, so two quickly came out 15 hours ago, Beechwood Chip said: Hah, same thing happened to me! I had to re-glue two magnets. This might be due to the type of plastic Grizzly used. If they used polystyrene or polyethylene plastics, these do not bond well to many (any?) adhesives that will bond with metal. I realized this when I tried to glue a magnet to the base of a small LED lamp. CA or epoxy would work for a bit, but the pull of the magnet was enough to break the glue bond. I solved the problem by purchasing magnets with a center hole and screwing them on. 4 Quote
Popular Post Von Posted September 22, 2025 Author Popular Post Report Posted September 22, 2025 My second 3-D printing job: a ZCI for my bandsaw. I couldn't find one for sale, though I admit Grizzly has me so confused with their model numbers and the differences between them, I may be missing it (I couldn't find one for a GO555LX and the one I ordered for a GO555X, assuming that surely would be the same, is a different size). 5 Quote
Mark J Posted September 23, 2025 Report Posted September 23, 2025 Do you have a 3D printer, or did you get this on line? Quote
Von Posted September 23, 2025 Author Report Posted September 23, 2025 On 9/23/2025 at 9:16 AM, Mark J said: Do you have a 3D printer, or did you get this on line? I printed it at my local public library. 1 Quote
Mark J Posted September 23, 2025 Report Posted September 23, 2025 Right, I should have remembered. I was at my local library recently and inquired about 3D printing. Apparently the board is considering adding the service. No time line, though . 2 Quote
Popular Post Von Posted November 1, 2025 Author Popular Post Report Posted November 1, 2025 I have a couple Rockler expanding hoses and they have frustrated me in terms of storing them. I first hung them over a peg, but they stretch out and manage to get in the way in all sorts of creative ways. I then hung them with a chain down the middle but that was a pain as trying to get the chain through the hose was like trying to push a wet noodle over a wet noodle. Cleaning out my step father's stuff, I found some 1" metal pipe (curtain rod?) and realized I could feed it through the hose more easily than chain since it is stiff, so I ran the chain through it and put a pivoting bar at the bottom to keep the hose from falling off. I turn the bar parallel to the pipe, push the host on and up over the bar, turn the bar perpendicular, and then release the hose. The pivot bolt goes through the last link of the chain, so the chain supports all the weight. So far so good. 5 Quote
Ron Swanson Jr. Posted November 1, 2025 Report Posted November 1, 2025 I like it @Von! The big feature to that hose is that it collapses to the smaller size when it's not in use, but it's still tough to store. 1 Quote
fcschoenthal Posted November 1, 2025 Report Posted November 1, 2025 I have one and hate that it collapses when it's in use too. Maybe I just haven't figured out the best way to use it. 1 Quote
Von Posted November 1, 2025 Author Report Posted November 1, 2025 On 11/1/2025 at 2:14 PM, fcschoenthal said: I have one and hate that it collapses when it's in use too. Maybe I just haven't figured out the best way to use it. Yeah, I've almost thrown them out as gimmicky. It's easy for the collapse to be a problem - I've had them pull tools off my bench when they collapse and I wasn't holding onto them! Where I've found they work well is from the end of a fixed hose on my ceiling to a sander (or other hand power tool) on my bench. Then the collapse pulls the hose out of the way, takes the weight of the hose off of the tool and it's a positive. 1 Quote
Tpt life Posted November 1, 2025 Report Posted November 1, 2025 Oh man, what was the name of the guy who lost his dentures? Don? 2 Quote
Popular Post Dave H Posted November 1, 2025 Popular Post Report Posted November 1, 2025 On 11/1/2025 at 1:10 PM, Tpt life said: Oh man, what was the name of the guy who lost his dentures? Don? particleboard! Oh I remember that post his false teeth fell onto a big drum sander one of those industrial kind and before he he could get everything shut off his teeth got sucked up in the dust collector! 3 Quote
Popular Post Von Posted November 2, 2025 Author Popular Post Report Posted November 2, 2025 Matt Cremona has a video where he is using an anemometer to measure the air speed his dust collector is producing when the meter gets sucked up into the ductwork. As I recall, the next few minutes of the video is him taking apart his ductwork to find the meter. One of the funnier YT moments I've come across IMHO. Edited to add: Found the video (FF to 22:25 if the link doesn't do so). 3 2 Quote
Popular Post gee-dub Posted November 2, 2025 Popular Post Report Posted November 2, 2025 I've sucked up safety glasses one time and a tape measure another. Both times the foreign objects made it to the dust bin. Thank goodness for cyclone designs. In my old baggers those things would have been pulverized (or worse). 4 Quote
Popular Post Von Posted November 17, 2025 Author Popular Post Report Posted November 17, 2025 Picking up from another thread, I recently adopted this old metal cutting band saw. It's clearly had an interesting life. It doesn't have legs, but even still it's heavier than I can lift so it's living on a shop cart a the moment. It runs and seems to basically work and I spent some time today triaging issues. The main issue I notice is this cover for the motor pulley, which was just held on by the pulleys and rattled loudly when the motor runs. I managed to pull the pulleys and get the cover off. The first thing I notice is someone has done some interesting expansion of the hole the motor shaft goes into - on the left, it should be a smooth arc, the cutting at the bottom was done by a previous owner. I'm wondering if someone replaced the motor with something close but a little different size that necessitated this. I need to spend some more time looking at it to understand if this expansion is needed and why. One end of the cover, on the right, just wasn't screwed down, so that should be an easy fix. The tab you see above is more interesting with the bit of engineering you see below. What you are looking at is the head of one of the bolts for the motor mount, which has been drilled and tapped to hold another smaller bolt, which passed through the tab. Kinda a Turducken situation with a bolt inside of a bolt. I'm assuming it didn't come from the factory this way as I've never seen this before, but if someone knows differently, I welcome learning. However, if it is not OEM, I'm not sure how the tab was originally attached. This bolt is in the right location, if a bit off vertically. My first thought was the motor mount bolt is also supposed to go through the tab, but it's way too big. My guess is there is supposed to be some sort of bracket that is missing. I found a manual online for this thing (a scanned copy of a physical document) but I can't tell from its parts diagram what should be going on. Besides that it just needs a good cleaning, some missing knobs replaced and a re-repair of its power cord. I also notice that the saw doesn't go vertical, it stops at about 70 degrees. I think most band saws like this are designed to have the blade go vertical and accept a table. The blade guard looks like it is designed to accept a table and the parts list shows one, so also on my list is to figure out why it doesn't go vertical. 3 Quote
wtnhighlander Posted November 17, 2025 Report Posted November 17, 2025 I've never seen a metal bandsaw with a controlled-lower feature that DID go completely vertical. Seventy degrees sounds about right. Works sort of like a chop saw. 1 Quote
Immortan D Posted November 17, 2025 Report Posted November 17, 2025 On 11/16/2025 at 11:48 PM, Von said: My first thought was the motor mount bolt is also supposed to go through the tab, but it's way too big. I think you're right. But since they replaced the motor and it didn't fit that way, they needed the bolt inside the bolt to be able to level the cover since it was not sitting properly with the modified assembly. The bolt inside the bolt is just pushing the cover up. 2 Quote
Popular Post Von Posted November 18, 2025 Author Popular Post Report Posted November 18, 2025 I largely disassembled the metal-cutting bandsaw yesterday. Besides one set screw I had to drill out and some light surface rust, no real issues. Even the guide bearings look good, which surprised me. I did confirm the motor and its mounting bracket it not OEM and I'm pretty sure physically larger than the original, which I think is causing some wonkiness. Will evaluate more carefully as I re-assemble. It does have a lubricated gearbox, which I have no experience with. Granted it was in the 40s F and I hadn't bothered to fire up any heat in the shop, but the current oil is as thick as pudding. I'm guessing I want to change just so I have a known state? I welcome any guidance from those with experience. On 11/17/2025 at 6:58 AM, wtnhighlander said: I've never seen a metal bandsaw with a controlled-lower feature that DID go completely vertical. Seventy degrees sounds about right. Works sort of like a chop saw. I'm fairly certain this bandsaw has the feature of going vertical. See excerpt from manual below and I've confirmed the lower/inner blade guard has bolt holes as shown for a table. At some point during my tear down yesterday, I noticed it would go fully vertical. I suspect the larger motor, which isn't shown in the image below but is hanging off the lower right of the body in the image, is getting in the way. 3 Quote
Mark J Posted November 18, 2025 Report Posted November 18, 2025 48 minutes ago, Von said: but the current oil is as thick as pudding. Isn't grease supposed to be thick? 2 Quote
Von Posted November 18, 2025 Author Report Posted November 18, 2025 On 11/18/2025 at 10:02 AM, Mark J said: Isn't grease supposed to be thick? If it's grease, then my frame of reference is way off. I assumed oil but, yeah, that's a guess. 2 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.