Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Von's shop tour and setup log

Featured Replies

I cut my pieces to a consistent length before cutting miters, and make sure the miter doesn't remove one scintilla of that length on the acute (sharp/pointy) side of the miter. 

So the miter is never a dimensioning cut that affects the length of the work piece. 

I hope that makes sense. 

  • Replies 387
  • Views 75.3k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • Immortan D
    Immortan D

    Count me in... I have enough "nice to have" tools that I never use. Things like the Starrett trammel set:   I never used that thing, not once, and I had it for many years.

  • Finally got some shop time yesterday and make progress on the in feed table. A got a couple of clamps and also some adhesive silicon pad. Building on the advice from wtnhighlander and Mark J, I replac

  • I'm blaming gee-dub for this upgrade :-) More seriously, in making the urn I was doing a bunch of micro-tweaking of my router fence to dial in the rabbet on the top and remembered his recommendation o

Posted Images

  • Author
On 5/23/2025 at 9:25 AM, Mark J said:

I was also thinking the jointer was the way to go, too.  But then I remembered, Von just sold his bench top jointer.

Von, have you considered using a box joint instead?

Right, jointer is gone. Obviously I could do a box joint instead. I should get some shop time over the weekend and I plan to make some test pieces and try out these various methods. Thanks!

I thought of another(!) fault with my suggestion.  The blade kerf will cut off the bottom corner of the alignment piece, which will make it difficult to make accurate repeat cuts.  The design needs a stop block behind the alignment piece to align the alignment piece.  So, alignment piece against the stop block, stock against the alignment piece, clamp stock to jig, remove alignment piece lengthwise (towards us in the diagram), and make cut.  Maybe an eye screw in the end of the alignment piece would make a good handle.

Box joints are looking better and better.

Why not cut close with whatever saw, and then plane to the line with a block plane?

  • Author
On 5/23/2025 at 7:52 PM, Don Z. said:

Why not cut close with whatever saw, and then plane to the line with a block plane?

In theory, no reason. In practice, we'd see if I'm skillful enough with my plane.

  • Popular Post

My experience with chamfer bits is that they are quite accurate. Cut the boards to final length and width on the tablesaw at 90*, then take as many passes as needed across the router table. I recommend using the fence, not the bearing bit, and moving the fence back in stages to remove the corners until only the slightest hint of square edge remains. Doing it this way, and passing all edges through the cutter at each step, should leave clean 45* miters and parts of perfect size.

The tiny flat at the joined corners can be left as a chamfer, rounded, or sanded away after assembly.

I suggested the fence over the bit bearing, because there is usually a small gap between the cutter and bearing, which would require a touch more flat edge to remain.

On 5/21/2025 at 7:50 AM, Von said:

I know my Kapex does long miters fairly well, but I've always found that an awkward cut.

I just realized you have a Kapex miter saw and that you said this. To me, this would be a perfect solution to your problem. Maybe someone on here can help you with the issues you are having with it? 

11 hours ago, wtnhighlander said:

The tiny flat at the joined corners can be left as a chamfer, rounded, or sanded away after assembly.

I'm not following why to leave the tiny flat?

  • Author
On 5/23/2025 at 10:05 PM, Coop said:

I just realized you have a Kapex miter saw and that you said this. To me, this would be a perfect solution to your problem. Maybe someone on here can help you with the issues you are having with it? 

It's a comfort issue. With the blade tilted to 45 and sliding, it's a lot of exposed spinning teeth moving around. And since the workpiece is clamped I have no idea what to do with my left hand, I just know I want it no where near the action and my pieces aren't long enough it can help in holding them in a way that feels safe to me. So I have to concentrate on keeping it away from the action when it wants to help if that makes sense. All together, it feels very awkward to me. I'm sure I could get use to it, but I just don't enjoy it.

BTW, I tilt the saw head to the right, since a R-to-L downward motion feels less awkward to me than tilting it left and having to go across my body to pull it down. I also find it easier to have the long side of my cut up since I'm more confident I know that measurement than the inside.

23 minutes ago, Von said:

It's a comfort issue. With the blade tilted to 45 and sliding, it's a lot of exposed spinning teeth moving around. And since the workpiece is clamped I have no idea what to do with my left hand, I just know I want it no where near the action and my pieces aren't long enough it can help in holding them in a way that feels safe to me. So I have to concentrate on keeping it away from the action when it wants to help if that makes sense. All together, it feels very awkward to me. I'm sure I could get use to it, but I just don't enjoy it.

BTW, I tilt the saw head to the right, since a R-to-L downward motion feels less awkward to me than tilting it left and having to go across my body to pull it down. I also find it easier to have the long side of my cut up since I'm more confident I know that measurement than the inside.

I totally get this and feel the same way.  When I set up my SCM for any cut I have the workpiece securely clamped in place.  Then before I start the cut I reach my left hand behind my back and wrap my fingers tightly around my belt.  I figure it will take at least a second to let go, during which time I hope my better judgment would kick in.  

2 hours ago, wtnhighlander said:

Once the flat is gone, the overall dimension of the piece begins to shrink. The flat can be hair-thin, but needs to exist.

I was thinking the second miter of each side would done with a stop block.  So each side would be equal length, but as you point out, not necessarily the "design" length.

On 5/22/2025 at 9:46 AM, Beechwood Chip said:

The video shows tilting the saw blade, and Von's problem is that his saw gets wonky if he tilts the blade, so he wants to leave it at 90.

Ah, there it is.  I was wondering why this wasn't a job for a tilted blade at the tablesaw. @Von-  Remind me what your tablesaw is please.  If it is not a contractor format we can probably get it aligned for success on these types of cuts.  If the motor hangs out the back, a sled is the way to go.  I have used ones similar to those shown at the bandsaw prior to having a saw with a robust tilting table.

  • Popular Post
On 5/21/2025 at 7:50 AM, Von said:

table saw is a ~30 year-old DeWalt 745 contractor saw.

This was two pages back, already.:) ( @gee-dub )

On 5/24/2025 at 8:46 AM, Beechwood Chip said:

I bought the "Million Dollar Stick" and keep it next to my CMS.  It lets me use my left hand to hold down the workpiece while also keeping my hand over a foot away from the blade.

 

+1

  • Author
On 5/24/2025 at 1:39 PM, gee-dub said:

Ah, there it is.  I was wondering why this wasn't a job for a tilted blade at the tablesaw. @Von-  Remind me what your tablesaw is please.  If it is not a contractor format we can probably get it aligned for success on these types of cuts.  If the motor hangs out the back, a sled is the way to go.  I have used ones similar to those shown at the bandsaw prior to having a saw with a robust tilting table.

As Mark J mentioned, it's an old contractor saw. The blade and motor pivot together from front-to-back, as I think is common for such a saw. My guess is that the pivot has enough play that when I loosen the mechanism to angle it, one side or the other is shifting. But your question makes me think about flipping the saw over and seeing what is actually going on and if I can improve things. It have have been this way since I got it or may have worn in over the years.

On 5/24/2025 at 9:46 AM, Beechwood Chip said:

I bought the "Million Dollar Stick" and keep it next to my CMS.  It lets me use my left hand to hold down the workpiece while also keeping my hand over a foot away from the blade.

Agreed, I have one as well and this is a good idea. Thinking it through, I'd need to put the waste side of the cut on the right of the blade since it's too small to grip. But I can't think why this wouldn't work. On the list to try. Thanks.

On 5/23/2025 at 10:17 AM, Von said:

I should get some shop time over the weekend and I plan to make some test pieces and try out these various methods. Thanks!

Best intentions. My back is a little unhappy with me from yesterday's work on the retaining wall, so need to take it easy. I appreciate all the suggestions and will report back, might be a few days.

  • Popular Post

@Von - I didn't mean to send you down the rabbit hole.  I have used contractor saws for many years.  They are roughing tools for the most part.  I have dialed them in to work great at 90° and made lots of good furniture with them.  Trying to get table mounted trunnions on my Delta or Craftsman saws to reliably change angles and return was a fools errand for me and I finally gave it up.  

Contractor format saws can do plenty.  I would setup your saw for a solid 90° and use the sled approach you describe.  I am not being critical of the saw.  I am just trying to save you going through the time and trouble I did only to end up back at 90°.  On the other hand; maybe it's me ;)

On 5/23/2025 at 8:52 PM, Von said:

In theory, no reason. In practice, we'd see if I'm skillful enough with my plane.

One can get a lot of practice in the time it takes to make a sled...

And there's no reason why a donkey ear or some such in a shooting board...

  • Author
  • Popular Post

Thanks for all the suggestions. Got some shop time today and tried three approaches suggested to the table saw for making mitered boxes: hand planing, band sawing, and the router table. As you'll see, any of the three would have worked. I ended up going with #3 out of personal preference.

#1: Hand plane. I marked a 45 on the end of a piece and threw it in my vise and went to town. Not surprisingly, this works, but was a little tedious. My little Bridge City block plane seemed most effective, I think because of its low angle, though it was not very comfortable (it's small and the depth stop gets in the way of my hand). If I were doing the eight miters for one box, I'd take the time to make a shooting board with a donkey ear and probably think hard about getting a low-angle jack plane.

PXL_20250527_182749702.thumb.jpg.3898fea7a0f7e3f6c59f63e2206b890d.jpg

PXL_20250527_184445258.thumb.jpg.8031ce5f8b12f836f24d4eaa158a4807.jpg

#2: Band saw. Set the table to 45 and used a miter gauge with a fence. The cut wasn't perfect but it cleaned up nicely with my block plane. The most challenging thing was holding the workpiece to start the cut since the table wasn't really big enough and gravity is not your friend for this operation. If I were doing this for eight cuts, I'd make a sled with some sort of clamp.

PXL_20250527_190357594.thumb.jpg.19c472858f29361c0f2c55c9885b6cab.jpg

PXL_20250527_192205982.thumb.jpg.a8eec403f8974f0fc64b1a446e6ea912.jpg

PXL_20250527_190532185.thumb.jpg.6200910bd92eb6ecd7598d101a40feed.jpg

#3 Router table approach with a template. I found a couple YT videos (e.g., e.g.) that show using a straight piece double-sided taped to the top of the workpiece so that after you cut the miter there was still something to ride against the fence besides the point of the miter. This reminded me of a Phillip Morley video where he used a template and an L-fence on the table saw to cut pieces for a mitered box. So I merged these two techniques. I made two templates, one the length of my long box sides and one the length of my short box sides. (The width doesn't matter too much as far as I can see as long as they are wide enough to provide good support against the fence - mine were close in width to my parts but not exactly.) I first use an L-fence on the table saw (set to 90) and the templates to cut my pieces precisely to length. My workpiece is the thinner piece below the template in the photo below, trimmed to match the template.

PXL_20250527_171926326.thumb.jpg.6c5cd579b1ac4bfae29cc67b1e997dee.jpg

Then I set up my chamfer bit on the router so the bearing is flush with the fence and I start with the bit low so I can sneak up on the cut. I started making passes slowly raising the bit until the 45 came to the edge of my workpiece. Once it was dialed in, I had no problem making the rest of my cuts in one pass. Each piece got flipped and mitered on both sides using each template twice. The nice thing I found is each pair of pieces are dead-on the same length because they used the same template. A down side is you need a big chamfering bit - mine was barely large enough to handle my ~3/8" work pieces, if they were any thicker I wouldn't have been able to do this approach without a bigger bit.

PXL_20250527_180028652.thumb.jpg.490c26f5dde3861a03e82d567fdef009.jpg

PXL_20250527_173946269.thumb.jpg.09cdd289422f63bf260e3f0cfcf38153.jpg

Again, thank you everyone for all the help.

 

 

Another thing I would note, if you raise the bit too high such that you're trimming the template, you will shorten the workpiece.  But if you machine both pieces at one time they will still be the same size.

  • Author
On 5/28/2025 at 9:47 AM, Mark J said:

Another thing I would note, if you raise the bit too high such that you're trimming the template, you will shorten the workpiece.  But if you machine both pieces at one time they will still be the same size.

Correct, everything would still be the same length but you'd start shrinking your resulting product, which may or may not be meaningful. I actually left a bit of a flat since (as someone else pointed out earlier in this thread) it will sand/plane away easily enough.

  • 1 month later...
  • Author
  • Popular Post

Put up the second of the two rails I found at Restore on my ceiling. This one at an angle from the corner where I usually keep my shop vac cart to my workbench.

These rails are 7' long and have 1/4" t-track in the bottom. I use t-track bolts with barrel nuts and an eye- or J-bolt to make mobile hangers. I put the first up over my workbench to try it out and it's been effective for power cords, dust collection hoses and holding up random work pieces. I decided I wanted the second one dedicated for holding up the hose to the shop vac and a power cord that switches it on.

PXL_20250720_145644004.jpg

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.