Ron Swanson Jr. Posted June 25, 2024 Author Report Posted June 25, 2024 On 6/25/2024 at 1:46 PM, drzaius said: Get a dado set without the full body chippers, which is what SawStop recommends. @drzaius When you say "without full body chippers" - do you mean like this? This is what i had previously and just rebought. 1 Quote
wtnhighlander Posted June 26, 2024 Report Posted June 26, 2024 Those chippers are useful as very precise, flat-bottom 'groovers' on their own. Just feed slowly. 1 Quote
Coop Posted June 26, 2024 Report Posted June 26, 2024 @Ron Swanson Jr., in your previous where you stated “the roof caved in” your first pic. Is that blade one of your two outside blades? Mine are typical 40t or so blades. SawStop or not, I would add a sacrificial fence to your miter bar and cut extras to be used with the dado set. You would not only have eliminated this problem but it will also provide you with a zero clearance backing for cleaner cuts. Not that your cuts on this bench don’t look pristine as it is! Quote
pkinneb Posted June 26, 2024 Report Posted June 26, 2024 @Ron Swanson Jr. FWIW Bourbon Moth Woodworking just did an interesting video on the SawStop and what will set it off I found it worth a watch 1 Quote
Ron Swanson Jr. Posted June 26, 2024 Author Report Posted June 26, 2024 @Coop yes, those are the outside blades. They each have 12 teeth. The only issue with what you prescribed is the dado cartridge on a Sawstop will only work with an 8"stack. It won't accommodate a 10" blade, which is what i think you're using? I was preparing to cut the tenons on top of the legs when this happened. I do have a 2nd miter gauge with a wooden fence on it but used this miter gauge today because the longer fence for the longer legs. Still though, you're absolutely right - the zero clearance sacrificial is a winner. Thanks! 1 Quote
Popular Post Ron Swanson Jr. Posted June 26, 2024 Author Popular Post Report Posted June 26, 2024 On 6/25/2024 at 9:27 PM, pkinneb said: @Ron Swanson Jr. FWIW Bourbon Moth Woodworking just did an interesting video on the SawStop and what will set it off I found it worth a watch Interesting video, thanks for sharing! I did trip mine with wet plywood once. The only theory i have as to why the wet wood didn't trip it in the test was that it wasn't wet enough. His wet wood was around 30% which IS very wet, but our bodies contain much more than that. It's also possible/probably that Sawstop has made refinements over the years and narrowed the swath of non-flesh materials that will trip the brake. So things that did trip out 10 years ago may not do so as frequently today. Just a theory though. 3 Quote
Popular Post Ron Swanson Jr. Posted July 15, 2024 Author Popular Post Report Posted July 15, 2024 Got the base pieces cut and joined, though it's far from complete. Here's where I'm at... Everything is playing nicely and is surprisingly square without yet seeing a single clamp. No real surprises here... 4 legs and 6 stretchers Mortises cut with a router and edge guide and straight bit. I tried rounding the tenons, which I've never done before. I didn't care for this method. Maybe just because it was new to me but i had trouble dialing in the fit. So i went with what I'm familiar with, and squared up the mortises. Which i now realize i didn't take pictures of. Mark the tenons and cut them on the table saw. I destroyed my old dado blade earlier in this thread and the new one i got (low end freud) is crap. The cut quality is terrible. So i ended up using a box joint blade. Oh well. Whatever works, I guess. This is likely the last time I'll use the table saw for tenons. Faster and easier to use the band saw, I think. Dial in fit with shoulder plane and router plane. Drill for the draw bore pegs. I'm holding off on the draw boring for now as i need the left front leg unattached for the leg vice. clean everything up with a smoothing plane and assemble. I still have plenty left to do on this base, but it's coming along. 9 Quote
Mark J Posted July 15, 2024 Report Posted July 15, 2024 The new bench is coming along nicely. The old bench it's sitting on doesn't look too shabby either. How do you have your dado blade set up? In the picture it looks like a single blade with two chippers? Quote
Ron Swanson Jr. Posted July 15, 2024 Author Report Posted July 15, 2024 On 7/15/2024 at 8:34 AM, Mark J said: How do you have your dado blade set up? In the picture it looks like a single blade with two chippers? Thanks @Mark J. I'm not using the dado blade to as the cut quality was terrible so I'm using a box joint blade. Which is similar to the 2 outer blade s in a dado stack with no chippers 2 Quote
Von Posted July 16, 2024 Report Posted July 16, 2024 Looking great! Excited to see the final result. 1 Quote
Ron Swanson Jr. Posted July 21, 2024 Author Report Posted July 21, 2024 Learned a lesson about trusting your intuition yesterday. I wasn't in the usual mindset that i am in when I'm in the shop. I had an argument with my wife and a few other things were diverting my attention and i remember thinking that i should just shut it down for the day. But I'm very limited on shop time and had been looking fwd to this day all week so i decided to keep at it. And sure enough.... Bam. Huge mistake. I didn't double check my layout against the plan and laid out these dog holes from the BOTTOM of the leg and not from the top. So they're now way out of position. I can plug the dog holes with dowels, or i can just live with them out of place. Crap. Should've listened to my intuition. 4 Quote
Popular Post Von Posted July 21, 2024 Popular Post Report Posted July 21, 2024 Sorry. It's frustrating how easy I find such mistakes are to make. Unsolicited $.02: I find in the long run I feel better when I challenge myself to do the best fix possible. 3 Quote
Ron Swanson Jr. Posted July 21, 2024 Author Report Posted July 21, 2024 On 7/21/2024 at 11:34 AM, Von said: Sorry. It's frustrating how easy I find such mistakes are to make. Unsolicited $.02: I find in the long run I feel better when I challenge myself to do the best fix possible. Thanks @Von. That's a great philosophy/strategy to have. You've got me thinking. My first thought was to plug the holes with dowel stock, but that end grain is going to stick out like a sore thumb. But.... If i filled with dowel stock and then covered with a veneer piece..... Hmmmm. I'm have to think this through. I'm not rebuilding the leg. Thanks! Quote
Von Posted July 21, 2024 Report Posted July 21, 2024 Plug cutter? If you have some scrap that is close, plugs from it will blend well. 1 Quote
Ron Swanson Jr. Posted July 22, 2024 Author Report Posted July 22, 2024 On 7/21/2024 at 3:43 PM, Von said: Plug cutter? If you have some scrap that is close, plugs from it will blend well. Thanks for the suggestion. I think you just nailed it. I have plenty of scrap to match this. Ordering one today! 1 Quote
Popular Post Ron Swanson Jr. Posted August 6, 2024 Author Popular Post Report Posted August 6, 2024 Chop and leg vise. Base mortise and tenon joints have been draw bored. Chop and leg vice installed: Chop is 1 piece 12/4 Walnut Next large mortise to receive the criss cross arms and the criss cross retro brackets. This same mortise in the left front leg and in the chop. Must not have have taken pictures but used a router and edge guide for these mortises. Bored 1-1/4" hole in both for the vise screw. Used a forstner extender instead of flipping for the very thick leg. Shallow mortise for the acetal bushing Shaped the chop on the table saw with tapers and chamfers I don't know if it was luck or what (probably luck) but i ended up with a perfect amount of toe-in on the leg vise, and it just runs silky smooth And that is where it's at. Hoping to have this mostly finished by the time i go back to work next week. 6 Quote
wtnhighlander Posted August 6, 2024 Report Posted August 6, 2024 Vise looks great. I am still amazed at the holding power a leg vise develops. That one should serve you quite well. 1 Quote
Ron Swanson Jr. Posted August 6, 2024 Author Report Posted August 6, 2024 On 8/5/2024 at 7:59 PM, wtnhighlander said: Vise looks great. I am still amazed at the holding power a leg vise develops. That one should serve you quite well. Thank you, i think so too. Benchcrafted did not mess around making this thing. It's built like a US tank. Quote
Von Posted August 6, 2024 Report Posted August 6, 2024 Looking great! Thanks for capturing all this. Hoping to do this myself sometime soon. 1 Quote
Popular Post Ron Swanson Jr. Posted August 6, 2024 Author Popular Post Report Posted August 6, 2024 On 8/5/2024 at 9:14 PM, Von said: Hoping to do this myself sometime soon. Go for it! I've had some challenges and frustrations but honestly it's been the most fun thing I've ever built. Of course I'm looking at it and thinking of all i would do differently if i were to ever do it again. I'm hoping this bench lasts me until i hang up my spurs. 4 Quote
Popular Post Ron Swanson Jr. Posted August 6, 2024 Author Popular Post Report Posted August 6, 2024 I'm questioning the decision to go with a split top. One giant slab would make this part much easier. Getting everything lined up so i can scribe the mortises has been very aggravating. Make one adjustment here and knock it out of alignment in 6 other areas. Cumulative error can really be a pain in the butt. I think i have itv dialed in now though. Knock wood. 3 Quote
wtnhighlander Posted August 7, 2024 Report Posted August 7, 2024 One giant slab would be tremendously heavy, and would tend to move more with humidity swings. Maybe join the two with a couple of battens screwed on until the joinery is done? 1 Quote
Coop Posted August 7, 2024 Report Posted August 7, 2024 I agree with @wtnhighlander but: things sometimes seem to linger on my bench longer than they should and I see the split as an ideal depository for these items. I know, I should clean as I go. 2 Quote
Ron Swanson Jr. Posted August 7, 2024 Author Report Posted August 7, 2024 On 8/6/2024 at 8:59 PM, Coop said: I see the split as an ideal depository for these items. I know, I should clean as I go. That's the idea for the gap stop. It will have slots to hold a few chisels,a small back saw, maybe a marking knife and pencil. 2 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.