Popular Post Ron Swanson Jr. Posted August 7, 2024 Author Popular Post Report Posted August 7, 2024 On 8/6/2024 at 7:43 PM, wtnhighlander said: Maybe join the two with a couple of battens screwed on until the joinery is done? Thanks! I ended up cutting a makeshift gap stop to fill the gap and then clamping it all together. That forced the slabs to behave themselves enough for me to mark out the mortises. I just got a little frustrated because it was a putzy affair and i got little else done today. Hopefully cutting the mortises tomorrow, and once done it will be a functional bench, though still with a lot of work left to go... 5 Quote
Ron Swanson Jr. Posted August 9, 2024 Author Report Posted August 9, 2024 The plunge stop mechanism came off my router while routing a mortise. Lucky the only damage was one small part of one mortise slightly deeper than what i was aiming for. Need to double check this in the future before hitting that power switch... 5 Quote
pkinneb Posted August 9, 2024 Report Posted August 9, 2024 At least you caught it before any real damage 2 Quote
Popular Post Ron Swanson Jr. Posted August 10, 2024 Author Popular Post Report Posted August 10, 2024 On 8/9/2024 at 2:37 PM, pkinneb said: At least you caught it before any real damage So... It happened again. Something is up. The cap is threaded and there's a little doughnut gasket. The first time i didn't think too much of it, but i made sure it was screwed on tight. I'm at a loss at to how it happened a second time. Now it has my attention. 3 Quote
Coop Posted August 10, 2024 Report Posted August 10, 2024 Since the adjustment is not made with this threaded stop, I would add a drop or two of Locktite to the threads before reattaching. 2 Quote
Ron Swanson Jr. Posted August 10, 2024 Author Report Posted August 10, 2024 On 8/9/2024 at 9:33 PM, Coop said: Since the adjustment is not made with this threaded stop, I would add a drop or two of Locktite to the threads before reattaching. Good idea @Coop. Thanks. Willco. Quote
Mark J Posted August 10, 2024 Report Posted August 10, 2024 I think the reason the pieces are threaded is to provide for "fine" adjustment of the depth. The O ring must be there to provide friction when turning the knob. Is the O ring oily? Correctly positioned? 1 Quote
Ron Swanson Jr. Posted August 10, 2024 Author Report Posted August 10, 2024 On 8/10/2024 at 8:56 AM, Mark J said: I think the reason the pieces are threaded is to provide for "fine" adjustment of the depth. The O ring must be there to provide friction when turning the knob. Is the O ring oily? Correctly positioned? You're on the money on both. Yes the o ring is correctly positioned. I added a little petroleum jelly to it. I think vibration must be loosening it. I've had that router for 10 years but it's seeing a lot of use in this bench build. I'll try some lock tight today. I thought about thread tape but the threads are a little too fine for that. Quote
Mark J Posted August 10, 2024 Report Posted August 10, 2024 My thinking is the O ring needs to create friction to hold the knob in position when the router is running. So I wouldn't want to lubricate it. Maybe the O is worn? 1 Quote
Von Posted August 10, 2024 Report Posted August 10, 2024 On 8/10/2024 at 10:58 AM, Mark J said: My thinking is the O ring needs to create friction to hold the knob in position when the router is running. So I wouldn't want to lubricate it. +1 - I'd put on Locktite and compress the O-ring when tightening. I don't see how the stop can stay in contact with the O-ring if you lower it, so I don't think it's meant to be adjustable. 1 Quote
Popular Post Ron Swanson Jr. Posted August 11, 2024 Author Popular Post Report Posted August 11, 2024 Still have a lot left to do. The slabs need to be leveled and flatten. Need to make the gap stop and sliding deadman and a lot more dogs. But it's getting closer. 9 Quote
gee-dub Posted August 11, 2024 Report Posted August 11, 2024 I would be very proud of that bench. You've done a great job on it and she is a beaut. I see many happy years of service ahead. 1 Quote
pkinneb Posted August 11, 2024 Report Posted August 11, 2024 Great looking bench! I suspect you will wonder how you got by without it once you're using it on a regular basis, I know I did. 1 1 Quote
Ron Swanson Jr. Posted August 12, 2024 Author Report Posted August 12, 2024 On 8/11/2024 at 3:38 PM, pkinneb said: Great looking bench! I suspect you will wonder how you got by without it once you're using it on a regular basis, I know I did. I sure hope so! My former bench left a lot to be desired. 2 Quote
Popular Post Geoffrey Posted August 12, 2024 Popular Post Report Posted August 12, 2024 Before I built my Roubo, my prior bench was mainly a work surface and drawer storage. I could secure workpieces to work the face of a board, but not the end or edge. After building the Roubo, every time I use it, I think, "I love this bench." 4 Quote
Popular Post Chestnut Posted August 13, 2024 Popular Post Report Posted August 13, 2024 Just finish the bench before you put it to work. I've never finished my bench, it's been nearly 5 years now. It's too late but i made the gap between the slabs wider than the plans to allow the handles of tools to fit in the middle. I can store tools in my till that sit well below the bench surface. I also wanted the top to be wider than 24". The first time you make something with legs that are 24" and try balancing it on your work bench you'll understand why mine is 26". That's a fail of the plans imo, 24" is such a common width having a little extra for bench width goes a long way. 3 Quote
Popular Post Ron Swanson Jr. Posted August 25, 2024 Author Popular Post Report Posted August 25, 2024 This morning i flattened and trued up the slabs. I am not confident enough in my hand plane skills to use them exclusively for this task so i went with a router and the offensive lineman of router bits - the spoilboard bit. Mounted 2 guide rails (2x6) on the sides of the slabs. Marc the Wood Whisperer has videos of using string to ensure that the rails are truly parallel to each other. I don't know if he came up with that on his own, or if it's an old timers trick -neither would surprise me. But it's simple and effective. The surfacing has left me with a surface that needs a little work. At this point i have no problem pulling out my planes to go the rest of the way -now that the heavy lifting is done. I don't want this to be glass smooth but i do want to deal with these. And in the OOOPS department, the holes for the barrel nuts in the shoulder vise are now poking through. I will have to fill them. 7 Quote
gee-dub Posted August 26, 2024 Report Posted August 26, 2024 Looking good. Those peek-a-boo holes will fill fine. I would get the vice mounted before I filled. BLO and wax has worked as a bench finish for me for 20 years. Refreshes easily and endures marks, scars, and tattoos. 1 1 Quote
Popular Post Ron Swanson Jr. Posted September 15, 2024 Author Popular Post Report Posted September 15, 2024 I wasn't nearly as flat and true as i had hoped, so that required some rework. I worked the bottom of the slabs where the shoulders of the leg tenons and the stretchers make contact. It took a while but eventually got things nice and flat. One more pass with the router on a sled and some hand plane work and it's pretty dang flat. No pics though. Next up is the sliding dead man. A quick template made this easy. m I forgot photos of the gap stop and shelf, but that's really simple stuff. Anyway, all done except a few minor adjustments to the dogs, and i just now realized i put BLO on the chop and leg BEFORE I added the crubber lining. So, not sure how well that's going to adhere now, but I'll give it time to dry first. Here's the finished bench: 6 Quote
Ronn W Posted September 16, 2024 Report Posted September 16, 2024 Beautiful. Be proud of it. Now get in there and start doing something on it. 1 Quote
pkinneb Posted September 16, 2024 Report Posted September 16, 2024 Looks amazing!! I love your dovetails and your sliding holdfast 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.