Woodworking_Hobby Posted July 20, 2025 Report Posted July 20, 2025 I am really struggling to get my miter saw square. 1. The blade is a high tooth blade and it is hard to get the square onto the blade without hitting the teeth. 2. I have adjusted the blade to the face but I still cannot get it to cut square in either direction. 3. Today I gave up and just used my table saw. My table saw does 99% but there are a few times it would be nice to use the saw and I really just did not want it collection dust. I can do about 25-inches long and about 8 inches in depth on the table saw, but a love those it would be nice to use the miter saw. I need to take the time when I am not in the middle of a project and try to tune up the saw. Does anyone fine that a video search on the internet and trying to see if the manufacturer has any tips or tricks to get the saw square? 1 Quote
Beechwood Chip Posted July 20, 2025 Report Posted July 20, 2025 Is the miter saw reliably out of square? In other words, if you cut three cuts are they all off by the same amount in the same direction? if not, then the saw is not reliable and I don't think you'll ever get to it cut a 90° reliably. If it is reliable, it should just be a matter of moving the 90° stop. What make/model miter saw do you have? 2 Quote
Popular Post Von Posted July 20, 2025 Popular Post Report Posted July 20, 2025 On 7/19/2025 at 8:23 PM, Woodworking_Hobby said: I am really struggling to get my miter saw square. How old is it? With age, bearings and other parts can just start wearing out and you may have a lost cause. Chip's question about it being reliable vis accurate is a good one. If it's not reliable, you're probably chasing your tail. On 7/19/2025 at 8:23 PM, Woodworking_Hobby said: 1. The blade is a high tooth blade and it is hard to get the square onto the blade without hitting the teeth. I always bury the blade (with the saw off) in the table so I can put my square against it above the teeth. The problem then is I need a third (and sometimes fourth) hand to then make adjustments. Eventually you are going to need to cut wood and check the wood for square, so you might consider going right to that step. It's a little slower, but sometimes that is what it takes. On 7/19/2025 at 8:23 PM, Woodworking_Hobby said: I need to take the time when I am not in the middle of a project and try to tune up the saw. Does anyone fine that a video search on the internet and trying to see if the manufacturer has any tips or tricks to get the saw square? Agreed - I've had to learn to slow down as I'm prone to being impatient when I'm in the middle of something else. Videos are good, if you can find a good one. Don't forget about your manual - those vary too, but some are good. If you are having to loosen something, adjust, and then tighten it, the tightening could be knocking it out of alignment. This is a very frustrating situation as it means you have to try and compensate/guess for the tightening. 3 Quote
Mark J Posted July 20, 2025 Report Posted July 20, 2025 Also, are your table & fence flat & straight? 1 Quote
wtnhighlander Posted July 20, 2025 Report Posted July 20, 2025 Is this a sliding compound miter saw? If so, the comment about worn parts is doubly important, given the number of moving components are involved. 2 Quote
JustAnotherGuy Posted July 29, 2025 Report Posted July 29, 2025 getting a miter saw dialed in can be a pain. The teeth definitely make it tricky to square off the blade. I’ve had better luck squaring to the flat part between the teeth or using a blade with fewer teeth just for setup. I just can't remember the youtuber who posted videos similar to the problem you are having right now but I am pretty sure it is out there. 1 Quote
Beechwood Chip Posted July 29, 2025 Report Posted July 29, 2025 I cut a piece of scrap, tested the angle against a square, tweaked the 90° stop, and repeated until I was happy. It was a while ago, but I don't recall it being a pain. I've never had to adjust it since. But, I've got a non-slider (DeWalt 715), so my experience might not apply. 2 Quote
Popular Post Ron Swanson Jr. Posted July 30, 2025 Popular Post Report Posted July 30, 2025 Here's how i square the miter gauge on my table saw. This should work the same with a miter saw. I think. Take a reasonably square block, Mark an X and cut through the X. Reassemble the X against a known flat surface, like the fence on your table saw. Flip the left side around so the now-half-of-an-X is facing down, and examine the joint. If it comes together nice and tight, you're square. If there's a gap on the side of the joint that's nearest the fence, i adjust my miter gauge counter clockwise, just a skosh. If there's a gap on the side that's away from the fence, adjust clockwise. The adjustments might be opposite on the miter saw, but the principle should be the same. I think. PS for any non Midwesterners out there, a skosh = 2 ticks & a smidge 2 2 Quote
BillyJack Posted July 30, 2025 Report Posted July 30, 2025 #1….. What saw are we talking about? Quote
Popular Post fcschoenthal Posted July 31, 2025 Popular Post Report Posted July 31, 2025 On 7/29/2025 at 8:06 PM, Ron Swanson Jr. said: Here's how i square the miter gauge on my table saw. This should work the same with a miter saw. I think. I've always used something like a 2x4 that has some height as well. You can then tell if the blade is 90 degrees vertically too. 3 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.