Lemon Lane Bar Posted August 30, 2025 Report Posted August 30, 2025 I have built an Ipe bar top from used marina planking. Run through a planer it looks great. I have sanded it with 120 grit sandpaper but still can feel little grabbing and very small splinters. I need a smooth finish but I would prefer not using epoxy. I want the more natural look. Any suggestion? 1 Quote
Popular Post wtnhighlander Posted August 30, 2025 Popular Post Report Posted August 30, 2025 Commercial, or home use? For light home use, you can probably get by with a hard wax oil, which feels very natural. Most recommend sanding to 150 or 180 for best penetration,but going to 220 will probably remove that splintery feeling better. 3 Quote
Popular Post fcschoenthal Posted August 30, 2025 Popular Post Report Posted August 30, 2025 First, welcome to the forum. A smooth finish will depend on several things. 1) What type of finish (top coat) you plan on using. For a bar top, you'll want something that is pretty protective from spills, etc. Some type of oil (Tung, BLO) will penetrate, but probably not what you're looking for. Several layers of poly would work and protect the best, but looks plasticky and you'd be better off with epoxy at that point. A couple of coats of a hard way oil will protect it and it's easy to reapply if it gets scratched. I've used a marine varnish, Halcyon, from TotalBoat that is water based and after a few coats looks great. 2) The higher grit you sand, the "smoother" it gets. You can go up to over 1000 grit and it'll shine without any finish on it. Best to follow the instructions on whatever topcoat you're using however. 4 Quote
Von Posted August 31, 2025 Report Posted August 31, 2025 Welcome! Echoing @wtnhighlander, going one or two more grits (180, 240) on the sanding will help. And finishing is often about trade-offs. If you need durability in a commercial setting, epoxy is probably your best bet. In a home setting, a hard wax oil is what I used when I want natural and know it won't take a lot of abuse. 2 Quote
Mark J Posted August 31, 2025 Report Posted August 31, 2025 I agree with the advice above. Definitely sand to higher grit (220/240). Then clean off the dust with a vac, and wipe down with mineral spirits. You may find that the surface is still a llittle"grabby". If so, applying a lacquer based sanding sealer might help (other opinions?). 2 Quote
Ron Swanson Jr. Posted August 31, 2025 Report Posted August 31, 2025 It's hard to know what your splinters are like without pictures, but it's common to raise the grain by misting with water before sanding. Some people do this after every grit, some only do it before their final grit. Otherwise, it could be that your planer blades are dull and/or taking too big a bite (though you said it looked great after planing so i don't know about that.) Once you're able to, can you post some pics? Thank you and good luck 2 Quote
Tpt life Posted August 31, 2025 Report Posted August 31, 2025 Ipe takes burnishing quite well. It also takes wax quite well. Those two things lead to a very renewable finish schedule. I would agree that you are too coarse and need to sand to a higher level, or break out card scrapers. 1 Quote
BillyJack Posted August 31, 2025 Report Posted August 31, 2025 If you cannot finish it at 150 and have grabbing , you have another problem. I have done countless jobs with IPE at the shop I worked at and never sanded beyond 150.... 1 Quote
curlyoak Posted September 1, 2025 Report Posted September 1, 2025 There is satin, semi gloss, and high gloss oil based spar varnish. The more gloss the more urethane. The more urethane the longer until it needs to be re done. The older I get the more gloss I want. the older I get the less I like refinishing. In the old days I preferred satin... 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.