Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

New to bandsaws and just got one. Need some advice

Featured Replies

So I picked up a WEN 3962 bandsaw (link for specs) over facebook marketplace for cheap because I wanted to resaw some boards.The machine was in good shape and I got a new blade on it. I followed the manual for adjusting the belts and blades and all the guide bearings. Everything is working but my blade is constantly binding and has little cutting power when I try to resaw. Am I just working with an underpowered saw here or is there something else that could be going on that needs my attention?

Are you supposed to lubricate your blade? The manual has no mention of this and to me it seems like that would just make it easier for the blade to slip off the flywheels so I didn't do it but the blade I bought came with some instructions that recommended chainsaw bar oil.

Here's an example of what I'm working on. It's a black limba board about 5.5 inches wide. My blade is .5 inches wide and 3 TPI.

resaw.jpg

I'm not familiar with that bandsaw but for a 10" saw that's a fairly heft cut and you may be pushing its limits. I would do that cut very slowly on my 14" Grizzly. How does it do for lighter cuts?

I don't lubricate my blade. If I did, I'd use some sort of dry lube designed for woodworking blades (e.g. Blade Cote).

  • Popular Post

Ooof, yeah... You're asking a LOT from a 10" bandsaw to resaw something that size. Resawing takes a lot of firepower and is usually done on larger machines. 

I've never waxed, or heard of waxing a bs blade. 

My best advice would be

* Sharp, new blade about 3 tpi

* Slow, slow, slow feed rate. 

 

On the plus side, it looks like a good straight and plumb cut, so your saw is pretty well tuned and dialed in. 

  • Author

I couldn't find a HP rating for it but it's 3.5 amps so using conventional math I guesstimate like .5 HP. I'm able to make the cut feeding it in like 2mm every 2-3 seconds. I basically go by the sound of the blade hitting air.

Other kinds of cuts do fine. I cut some ash as a test piece making a rip cut using this same blade and it worked great.

Do you all think it would be a big difference if I upgraded to a 1 HP saw? I'm only like $200 into this thing and don't mind replacing it if it would be a big difference.

  • Popular Post

As others have said, that’s a pretty hefty cut. Although the kerf looks pretty consistent, you might try driving a wedge into after you’re several inches into the cut.

  • Author

Do you mean using a wedge to keep the cut boards from binding in on the blade?

51 minutes ago, Meatwad said:

Do you mean using a wedge to keep the cut boards from binding in on the blade?

Yes.

  • Author

If I upgrade does anybody have any recommendations? The lagunas from woodcraft came recommended here before but I am a little nervous about their 'no return' policy.

I’ve been using a Grizzly 14” with a riser block for about 10 years and am completely satisfied with. It has a high fence and resawing is a breeze. 

21 hours ago, Meatwad said:

The lagunas from woodcraft came recommended here before but I am a little nervous about their 'no return' policy.

Who has the no return policy, Woodcraft or Laguna? If it's Woodcraft you could try another retailer.  But realistically it's not that easy to return a floor standing power tool.

If you do get to the point where you are considering  14" bandsaw, the first thing to decide is if you want to go 240V or 120V.  

  • Popular Post

Don't be too hard on the machine.  It is about 1/3 of a horse.  My 10" Rikon is very slightly more powerful and does well up to about 4" of cutting height in things like oak.  I may be a knuckle-dragging troglodyte but in cars, sound systems, and bandsaws technology is great but it is no substitute for raw power :D.

Seriously though, a lower tooth count blade will cut faster but not as clean.  A higher tooth count blade will cut cleaner but not as fast.  If I use my Rikon within its capabilities it does a very serviceable job.  If I try to treat it like a 3HP 19" machine it will fail.

Some woods react when the stress is relieved during cutting.  This happens on any saw; its the wood, not the saw.  Keeping an old rattle-can lid full of small wedges nearby will allow you to fit one into the kerf behind the blade if the material you are working tends to grab.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.