Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Workshop air/dust meter?

Featured Replies

  • Popular Post

Any recommendations for an air quality meter for the shop? My goal is to measure dust levels. Ideally it'd have alarms if certain levels are reached.

Turns out over the weekend, sometime when I was doing all the planing, my dust collector bag got disconnected somehow, so all the fine dust getting through the first phase was just getting blown into the room. I didn't notice until this morning when I went back until the shop and noticed the layer of dust on everything. So my goal is less fine nuances and more "Something is majorly wrong with the D/C."

TIA

  • Popular Post

I use the Dylos DC1100. I paid a couple of hundred bucks back in the day but have never regretted it.  Whenever I am doing something that is not going to be well collected by my overall system I turn it on.  When the numbers get too high I stop what I am doing and go in for a coffee or a snack.  The ambient air scrubbers I run during such sessions will turn the air volume of my shop around about every 6 minutes so even really nasty air gets "safe" in about 1 cup of coffee.

I do not run the air scrubbers when using high VOC finishes because I do not want them sucking that up and killing the filters.  But for good ole wood dust I run a couple of 1000 CFM units with input, bag-style and output filters.  Just like with a good hand plane, the joy of the tool long outlives the pain of the cost.

  • Popular Post

I bought one of these off a much shadier site 4 years ago. I can say that the sensor gives you a good idea of particles in the air. 

As far as ultimate accuracy I can't say too much as I'm not an expert and can't state any sort of calibration. I can say that I've had it outside during the air quality alerts we've had recently and the meter is within 10% of the fancy meter they use to report on airnow.gov. 

It is accurate enough that i can tell when there is dust in the air via the meter before i can tell from other methods. The dylos is a better meter measures down to 1.0 micron. So you get what you pay for. I agree in it being nice to have one. I've used mine more outside during smoke events that I ever did in my shop. It puts the wife at ease when the kids want to be outside but there is an air quality alert.

I looked at getting a quality meter about a year ago. I was looking at the ones that measured VOCs as well. But then I saw that all of them only got down to about 2.5 microns, so I gave up. I guess I prefer to live in blissful ignorance. :D

  • Popular Post
On 7/27/2026 at 3:03 PM, Chestnut said:

I bought one of these off a much shadier site 4 years ago.

I've got a Dylos, but I only looked at it when I was testing different dust management approaches.  At that price, I might get one of these and compare the readings with the Dylos.  I like the "visual alert" and it might be easier to read from a distance.  The negative reviews say that it's not accurate at very low counts, but for a wood shop if the counts are very low I don't really care.  Some reviews said that it stopped working after a few days, but that's what Amazon's return policy is for.

My Dylos detects down to .5 micron.  There are various versions.  Mine is the "Pro" version. I do find that I get lost in the moment and don't keep a realistic visualization of the air I am breathing (respirator or not).  The meter just helps me stay in tune with my environment.  I walked a friend into the  shop just today to show him some progress on a project.  He made it about 3 feet into the shop and had to back out.  I thought it was fine.  We sometimes need a bit of science to override our amazing human ability to adjust to situations.

  • Author
20 hours ago, gee-dub said:

I use the Dylos DC1100.

I saw a couple of these used on ebay for <$100 so I've rolled the dice on one. I'll report back. Thanks all!

  • Popular Post

I had a couple of the cheap ones that Chestnut mentioned and they died. I enjoying having them to know when levels returned to normal, but it seemed like my cheap sensor never reset after I stopped working and was running an air filter.

I never thought to look for a used Dylos. Might have to add it to the list of things to look at. I wear a respirator the whole time I'm in the shop but I'd like to know at what point I need to take a break even with a respirator on.

  • Popular Post
21 hours ago, Chestnut said:

I bought one of these off a much shadier site 4 years ago. I can say that the sensor gives you a good idea of particles in the air. 

As far as ultimate accuracy I can't say too much as I'm not an expert and can't state any sort of calibration. I can say that I've had it outside during the air quality alerts we've had recently and the meter is within 10% of the fancy meter they use to report on airnow.gov. 

It is accurate enough that i can tell when there is dust in the air via the meter before i can tell from other methods. The dylos is a better meter measures down to 1.0 micron. So you get what you pay for. I agree in it being nice to have one. I've used mine more outside during smoke events that I ever did in my shop. It puts the wife at ease when the kids want to be outside but there is an air quality alert.

I have had one of those for quite a few years now and I really like it. Accuracy is reported to quite good. It isn't as finished as a Dylos and needs an external power source. I just velcroed a USB battery, which lasts many dozens of hours, to the back on mine.

It's a great value.

  • Author
  • Popular Post

The Dylos arrived today and seems to be working as far as I understand it, which is not much at this point. I found the manual and will endeavor to educate myself.

PXL_20260803_190129803.thumb.jpg.c415f15949e3a1ea7ee797c50930b713.jpg

 

  • Popular Post

That's the one I have.  I stuck a patch of Velcro to the bottom of it and the mating piece of Velcro to the top of an outlet box in the approximate center of my machine area.  I ran the power cord up to one of the overhead power outlet positions and presto.

Dylos-1.thumb.jpg.dfdfa2767692815f45621cb3ae47b6e6.jpg

When I am doing nasty things like sanding or freehand routing I just glance over at it now and again.  If it gets into the (read in an Archer voice) 'Danger Zone' I take a break for a cup of coffee or a snack.  The ambient cleaners bring things back to normal in 20 minutes or so and I carry on.  By paying attention I have eliminated sinus headaches and the nose problems associated with bad air. YMMV.

  • Author

A few things I've discovered using this meter for a week:

  1. I cannot see most of the dust in my shop. The meter will show bigs swings I would not be aware of otherwise.
  2. Everything I do in the shop kicks up some amount of dust, including just walking around. The big dust generator so far is, not surprisingly, sanding. Even with my shop vac attached attached to my ROS, levels shoot through the roof.
  3. This meter could easily make me paranoid about breathing.
  4. It is very useful for telling me when my air cleaner has finished doing its job cleaning the air.
  5. As I figure out baselines, it will be useful for telling me when something is wrong with my DC.
  6. When I make changes, it will be useful for telling the DC impact of the changes.

 

  • Popular Post
On 8/9/2026 at 2:48 PM, Von said:

A few things I've discovered using this meter for a week: I cannot see most of the dust in my shop.

Amen brother.  The dust that does us the most damage is the stuff we really can't see.  I use additional pre-filters on my HVAC since I now know that all that stuff I can't see is getting pumped through my mini split.  That benefit alone probably paid for the meter. 

I am often prompted (based on the meter readout) to wear a respirator at times that I normally would not.  There are also times I just take a break and let things settle.  I have often entered the shop to find the meter at double digits and without even firing up a power tool, it goes to triple or more.  This tells me it is time to take few minutes and run the shop vac over the work surfaces and floors.

  • Author

Bought this JET 1000B on Craigslist. Per the specs, it moves over twice the CFMs as my current WEN. I plan to use the Dylos to compare how long it takes the two to clean the shop air.

PXL_20260812_181633271.jpg

I've seen shops that run more than one of these filters at the same time.

(I vaguely recall, though, that they don't clear the super small particles).

  • Popular Post
On 8/13/2026 at 5:50 AM, Mark J said:

I've seen shops that run more than one of these filters at the same time.

(I vaguely recall, though, that they don't clear the super small particles).

I run two of them in a 1200 sq ft shop.  An older JDS-750 and an old model Jet AFS-1000 which is a clone of the JDS.  They are near opposite walls and face the opposite directions to create a circling of the air space.  They are certainly not all you need if you are doing an operation that creates a lot of 'hard to collect at the source' spoil like free hand routing. However, you can stand and watch the PPM numbers on the meter drop pretty quickly once you've stopped generating spoil. 

The Jet I have came with a 1 micron inner pocket filter.  I replaced the JDS inner pocket filter with the same.  Outer filter is 5 micron but cleanable. Being a child of the 60s I have a wind chime hanging at the exit to one of them.  Makes me smile when I shut the ambient cleaners down to hear the chimes ring on for a spell while I'm cleaning up.  I must have enjoyed the 60s too much.

  • Author
7 hours ago, Mark J said:

I've seen shops that run more than one of these filters at the same time.

(I vaguely recall, though, that they don't clear the super small particles).

I was checking out possible mounting locations this morning. Boy, the Jet filter is big. Not a lot of places I can put it between lights, shelving, garage door openers, etc. But there is a spot right next to my current filter it will fit. I'm sure that is not ideal but will let me install the Jet without taking down the old filter first, which is nice sice I don't have to worry about get interrupted and somehow ending up between filters or having to find a place to store the old one until I move it along. So I plan to install it right next to my old one and then figure out what I want to do long term. I may be able to find a better spot for the old one (which is about 1/4 the size).

  • Popular Post
On 8/13/2026 at 4:15 PM, Von said:

But there is a spot right next to my current filter it will fit.

I try to avoid "short circuits", where the filtered output air goes directly into the intake of another filter.  I think putting two filters in parallel will be fine.

I built my own air filters.  I wanted a design that used standard generic furnace filters, had high MERV filters with lower MERV pre-filters, and was easy to build with inexpensive materials.  I based my design on 20" x 20" x 1" MERV 16 filters.  I used 1/8" plywood strips to build 2" x 2" "L" shaped rails, then glued four of those together to make a square.  Five squares make a cube with one open side.  I attached generic box fans to the open side to pull air out of the cube.  The MERV 16 filters go in first, and then the pre-filters (also 20" x 20" x 1") go outside of those.  I use 1/8" bungie cord to hold the filters in place, but there are lots of solutions.

Dimensions are all relative to the actual size of the filters.  I bought the filters first and built the frames around them.

When the pre-filters look dirty I change them, and while they are out I change the inner filters if they look dirty.

I have two of these in my 40' x 15' shop.  One is hooked up to the light switch, so it's on whenever I'm in the shop.  The other is on a timer so it's on from 11am to 6pm every day, which is when I'm usually in the shop, and from 1am to 2am every day, which is when the Roomba runs (actually, it's a Eufy C10, but "Roomba" has become a general term, like "Kleenex" and "Xerox").   

 

Air Filter 1.jpg

Air Filter 2.jpg

Air Filter 3.jpg

Air Filter 4.jpg

Well done.  I ran something similar for years.  It worked fine and I could find filters on clearance now and again if I paid attention.  Economical, effective. and I was happy with it.  I believe that when I passed it on I passed a quantity of filters with it.  Win-win.

On 8/13/2026 at 1:15 PM, Von said:

I was checking out possible mounting locations this morning. Boy, the Jet filter is big. Not a lot of places I can put it between lights, shelving, garage door openers, etc. But there is a spot right next to my current filter it will fit. I'm sure that is not ideal but will let me install the Jet without taking down the old filter first, which is nice sice I don't have to worry about get interrupted and somehow ending up between filters or having to find a place to store the old one until I move it along. So I plan to install it right next to my old one and then figure out what I want to do long term. I may be able to find a better spot for the old one (which is about 1/4 the size).

Don't ignore turning it 90 degrees to make it fit in an otherwise difficult space.  The Jet manual even describes how to mount the brackets so you can wall mount the unit.

  • Author

We could probably have a whole thread dedicated to one-person shop tricks for getting tools into place, but I will say the combination of the Huskey adjusting table, Fastcap 3rd Hand and a extra long piece of chain were invaluable.

PXL_20260816_133724408.thumb.jpg.2aef7b990856462eff106ce3a9198e41.jpg

And it's installed and working. The WEN will stay next to it until I figure out what I want to do with it.

PXL_20260816_135918236.thumb.jpg.c66f1181b7a3782c68eeaedaf0aaef73.jpg

And I wish I could remember who to credit for this, but when drilling holes through ceiling drywall, a plastic cup around the drill bit to catch the dust works great!

PXL_20260814_161433638.thumb.jpg.344569606e6b0e15021bb8db5bd2bf5b.jpg

  • Author
On 8/15/2026 at 1:12 PM, Beechwood Chip said:

I got curious about how effective my air filters are, so I checked my Dylos DC1100 (not Pro) meter.

Air Filter Numbers.jpg

After that, progress got very slow.  So, better than nothing.

@Beechwood Chip For comparison, here are some measurements I took today. The spikes are all track saw cuts, some of which were pure skimming cuts without wood on one side so the dust collection was close to nonexistent (actually for the first cut, I forgot to connect the hose, so it truly was nonexistent). My Jet was on medium through most of this, though I turned it down to low towards the end. As you can see, I see some huge swings. My steady state tail is close to what you see: <100 for small (.5 micron) particles and <10 for large (2.5 micron).

air.thumb.jpg.2e1cddf2fa823a5accbf8d3d29274783.jpg

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.