Popular Post Beechwood Chip Posted September 26 Popular Post Report Posted September 26 I had the stop collars with a set screw to lock them in place, but it was finicky to get the screw to line up with a flat on the drill bit. So, I bought these Powertec split ring stop collars which in theory solve that problem by gripping the drill bit firmly over a larger area. I went to use the Powertec collars on a 1/4" drill and it failed miserably. no matter how much I tightened the screw, the collar would still slip. Eventually, the supplied hex wrench cammed out and rounded over. I switched to a 3/32 hex key from my set and it too cammed out. So, I'm back to using painters tape on the drill bit. Does anyone know of a stop collar that works reliably on twist drills? I can't use my drill press for reasons. 3 Quote
Popular Post Ron Swanson Jr. Posted September 26 Popular Post Report Posted September 26 Sorry I got nothing for you. But in the past, I have made physical stops from a block of scrap. Crude but very effective. But most of the time I just do what you do and bust out the painters tape! 4 Quote
Beechwood Chip Posted September 26 Author Report Posted September 26 On 9/26/2026 at 6:57 PM, Ron Swanson Jr. said: I have made physical stops from a block of scrap With a screw to hold it in place, or thick enough to touch the chuck? Quote
wtnhighlander Posted September 26 Report Posted September 26 +1 to a physical stop. Long enough to bottom on the chuck. Can't slip that way! 2 Quote
Ron Swanson Jr. Posted September 27 Report Posted September 27 On 9/26/2026 at 6:12 PM, Beechwood Chip said: With a screw to hold it in place, or thick enough to touch the chuck? Thick enough to touch the chuck. 2 Quote
Von Posted September 27 Report Posted September 27 +1 to @Ron Swanson Jr.'s idea: basically a custom spacer to set the depth. I agree with your overall problem statement: depth stop suck. You are causing me to think about it and I basically don't use them for all the reasons you give. 1 Quote
Popular Post gee-dub Posted September 27 Popular Post Report Posted September 27 The block of scrap absolutely works. I have a couple of collet style ones that work OK if you are careful. If you want something to dead-stop the depth repeatedly go with the blocks of scrap 3 Quote
Popular Post wtnhighlander Posted September 27 Popular Post Report Posted September 27 One more comment: this type of spacer is the wrong application for that scrap of SPF 2x4 you have lying around. The drill chuck jaws will easily dig in to the soft wood and ruin your precisely measured and cut space. Go hardwood, all the way! 5 Quote
Popular Post gee-dub Posted September 27 Popular Post Report Posted September 27 On 9/27/2026 at 7:58 AM, wtnhighlander said: One more comment: this type of spacer is the wrong application for that scrap of SPF 2x4 you have lying around. The drill chuck jaws will easily dig in to the soft wood and ruin your precisely measured and cut space. Go hardwood, all the way! Agreed. Scraps of pecan left over from a kitchen hutch build years ago still come in handy. Like Clint says: https://www.youtube.com/shorts/-e0IkNR34b8?feature=share Seriously though, any decent hardwood will do. I keep a 5 gallon bucket of kindling sized scraps around for just such situations. If the bucket gets full we make S'Mores with the grandkids and start filling it again. 4 Quote
Popular Post Tpt life Posted September 27 Popular Post Report Posted September 27 Back on depth stops, the hammer drills I have used, had rods that ran along the drill body, not stop collars. I have not looked, but wonder if you could get one that fits your drill? 3 Quote
Chet Posted September 27 Report Posted September 27 I have been using these drill stops from Lee Valley and have been pretty happy with them. 2 Quote
Beechwood Chip Posted September 27 Author Report Posted September 27 On 9/27/2026 at 1:04 PM, Chet said: I have been using these drill stops from Lee Valley and have been pretty happy with them. Hmmm, $41 more and I get free shipping. Any suggestions? 2 Quote
Popular Post Ron Swanson Jr. Posted September 27 Popular Post Report Posted September 27 On 9/27/2026 at 12:09 PM, Beechwood Chip said: Hmmm, $41 more and I get free shipping. Any suggestions? Without a doubt, one of my most frequently used tools is their base model marking gauge. I believe it's right around $40. If I ever, God forbid, had to start selling off my tools, this would be one of the very last to go. 4 Quote
Beechwood Chip Posted September 27 Author Report Posted September 27 On 9/27/2026 at 1:28 PM, Ron Swanson Jr. said: their base model marking gauge Nice! But I already have a "good enough" marking gauge. 2 Quote
Ron Swanson Jr. Posted September 27 Report Posted September 27 You could buy 2 plow plane blades for $44... Quote
Beechwood Chip Posted September 27 Author Report Posted September 27 Good suggestion! I think I'll get the miniature router plane. Quote
Ron Swanson Jr. Posted September 27 Report Posted September 27 Dang it. It's almost like you saw this obvious setup coming from a mile away! 2 Quote
gee-dub Posted September 27 Report Posted September 27 On 9/27/2026 at 10:09 AM, Beechwood Chip said: Hmmm, $41 more and I get free shipping. Any suggestions? My favorite marking gauge is the Stainless Steel Anniversary version. What makes it great is the eccentric rod placement. It is not commonly offered but this version has the same benefits. The micro-adjust is just a bonus. 2 Quote
Mark J Posted September 28 Report Posted September 28 There's this drill depth measuring tool: https://www.leevalley.com/en-us/shop/tools/hand-tools/marking-and-measuring/rules/110182-veritas-drill-stop-gauge 1 Quote
Popular Post wiki21 Posted October 1 Popular Post Report Posted October 1 On 9/26/2026 at 2:58 PM, Beechwood Chip said: I had the stop collars with a set screw to lock them in place, but it was finicky to get the screw to line up with a flat on the drill bit. So, I bought these Powertec split ring stop collars which in theory solve that problem by gripping the drill bit firmly over a larger area. I went to use the Powertec collars on a 1/4" drill and it failed miserably. no matter how much I tightened the screw, the collar would still slip. Eventually, the supplied hex wrench cammed out and rounded over. I switched to a 3/32 hex key from my set and it too cammed out. So, I'm back to using painters tape on the drill bit. Does anyone know of a stop collar that works reliably on twist drills? I can't use my drill press for reasons. Man, that Powertec split ring failing is a bummer, I've had the same problem. The set screw design is just too finicky. I've had better luck with the General Tools split-ring set, or if you want to splurge, the Woodpeckers Precision Stops actually hold. For a quick fix, painters tape is honestly still undefeated. 4 Quote
Popular Post pkinneb Posted October 2 Popular Post Report Posted October 2 On 9/27/2026 at 9:24 AM, gee-dub said: The block of scrap absolutely works. After messing around with a collar for 5 min last night I just cut a scrap of wood, drilled a hole in it, and bam, good to go! Anybody want to buy a nice set of barely used collars 3 3 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.