Brian VanVreede Posted January 9, 2012 Report Posted January 9, 2012 I spent a little over an hour trying to flatten the back on my new 1.5" Bacho chisel with my Shapton stones. I progressed from 500 to 2000 to 8000. The first quarter of an inch behind the edge.is a.perfect mirror,then there is about an inch of "hazy mirror" and then back to a perfect mirror. Is this a problem because I know that seeing this means my back I not Dead flat. Should I just go back to the 500 stone and work my way back up through the grits again? I think this set will last me a very long time and I only want to have to flatten the backs once so I think it would be pretty cool if I could get the backs on each and every chisel to be a perfect mirror finish. Is this a pipe dream or common place amongst the pros? Quote
flairwoodworks Posted January 9, 2012 Report Posted January 9, 2012 It depends on the chisel. Some chisels come with backs flatter than others. I would not worry about it and just start using them. Quote
Vic Posted January 9, 2012 Report Posted January 9, 2012 I don't anyone polishes the entire back, just enough to create a sharp edge. (null) Quote
Hans_Christopher Posted January 9, 2012 Report Posted January 9, 2012 I find that a mirror edge on the back of a chicel or plane blade is not really neccesary. I find that a flat back is more important, and if your chisel dips after a quarter inch I think you may have a problem registering your chisel on a work piece in some cases. To flattten the back of my chisel and planes I find it easiest to use sand paper (aluminum oxide) on the flatest surface avaliable; I use an offcut of a granite counter top. I start with a 180 and work there until I have a consistent scratch pattern across the entire back then i work all the way up 600 grit and stop there. At the end I put the chisel or plane blade down on the surface and try to fit a .0015 feeler quage under the area I have flatened If the guage doesnt go under the blade job well done and now I move onto sharpening. Check out http://tatteredjeansandsawdust.blogspot.com/2011/09/dull-day.html to see the full process with pictures. Cheers and hope this helps Hans Christopher Quote
wilburpan Posted January 9, 2012 Report Posted January 9, 2012 From what you are describing, I think your chisels are good to go. By the time you wear the chisel down to the hazy area, you'll be so good at sharpening that it will be trivial to get it to the point that you want. And my bet is that by then, you'll have figured out that perfect flatness on the back of a chisel is overrated. Quote
pagel Posted January 9, 2012 Report Posted January 9, 2012 If you do decide you want to polish the back, remember to get a consistent scratch pattern before moving on to the next grit. And don't make too large of a jump between grits, e.g., from 220 to 600. I usually go through the following grits (sandpaper) when flattening/polishing the back of a chisel - 220, 320, 400, 600, 1000, 2000. I don't go beyond 2000. I agree with the others that polishing the entire back isn't necessary for function, but I do it partly for aesthetics reasons and practice; it also satisfies that OCD part of me. I've learned quite a bit this way through trial and error - the best teacher. Also, moving up through the finer grits, to 8000 for instance, isn't just a matter of aesthetics. You're creating a sharper edge by bringing the two planes (the back and the bevel) closer to that ideal zero radius, which of course you'll never reach, and the entire back obviously doesn't need that level of polish to accomplish that. The question is how sharp is sharp enough... Quote
Brian VanVreede Posted January 25, 2012 Author Report Posted January 25, 2012 before and after... Quote
mwatkins Posted January 25, 2012 Report Posted January 25, 2012 before and after... As a few of the others have already said I think you're in great shape. Based off of the before and after pic I don't see any reason that you should worry. I will typically only end up with about the first 1.5" polished to a shine on my chisels, but for me that's fine as I rarely ever do anything that would require me to register the chisel much deeper than that. Quote
Chris Adkins Posted January 25, 2012 Report Posted January 25, 2012 I wouldn't worry at all about were you are Brian. By the looks of the picture I would say that you are in pretty good shape. Quote
flairwoodworks Posted January 25, 2012 Report Posted January 25, 2012 As a few of the others have already said I think you're in great shape. Based off of the before and after pic I don't see any reason that you should worry. I will typically only end up with about the first 1.5" polished to a shine on my chisels, but for me that's fine as I rarely ever do anything that would require me to register the chisel much deeper than that. I wouldn't worry at all about were you are Brian. By the looks of the picture I would say that you are in pretty good shape. I agree that Brian looks to be in good shape, but what about his chisel? Quote
JohnnyNoName Posted January 26, 2012 Report Posted January 26, 2012 before and after... Brian - When they say you should be able to shave with it, they are only talking about replacing the razor, not the mirror :-) As long as the front 1/4" or so is "mirroresque", you should be fine. "Grind, hone, get back to work" - The Schwarz. Jonathan =============================== Quote
Brian VanVreede Posted January 26, 2012 Author Report Posted January 26, 2012 Still haven't ground them, waiting until I build my jig for my grinder. Soon... .. Quote
aengland Posted January 26, 2012 Report Posted January 26, 2012 The first quarter of an inch behind the edge.is a.perfect mirror For now, that's all that matters! You're ready to go. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.