Recommended Posts

Posted

I have a standard sized circular saw but would like options for something smaller and easier to handle for rough cutting sheet goods down to size. I have considered a jig saw (and have a couple in mind) but wasn't sure if that would be the best tool for this task.

Any suggestions?

Posted

Circ saw's as good as it gets in my opinion. Jig saw's too slow.

-- Russ

I agree. Use a Circ saw with the sheet material resting on some rigid foam insulation for full support of the material and a straight edge clamped to the sheet material is the way to go unless you want to spring for a track saw. Just make sure you have a half-way decent blade for the circ saw (not the junk blade it comes with).

  • Like 2
Posted

I asked Marc why he used a jig saw to rough cut sheet goods, instead of a circular saw. He said that the jig saw is safer (which is true). I tend to use a circular saw, but I recommend jig saws to my friends who are looking for their second power tool after a cordless drill. I guess I might use a jig saw if I was concerned about safety for some reason.

+1 on getting a plywood blade, whichever saw you use.

Posted

I have a Milwaukee Jig saw with both variable speed and variable orbit. With the right combination of speed, orbit and blade you can get either a super fast cut (as fast as I would cut with a circ saw) or a super smooth cut or anywhere in between. If I had to cut sheet goods down with it I would not feel at all limited.

That being said, I usually use a circular saw with a guide clamp and an extra base that rides in a track on the clamp. Straight smooth cuts right on the line.

Posted

I asked Marc why he used a jig saw to rough cut sheet goods, instead of a circular saw. He said that the jig saw is safer (which is true). I tend to use a circular saw, but I recommend jig saws to my friends who are looking for their second power tool after a cordless drill. I guess I might use a jig saw if I was concerned about safety for some reason.

+1 on getting a plywood blade, whichever saw you use.

if im not using the table saw or if the kids in classroom need to cut a back for a shelf i have them use jig saw safer for them then they just sand down any ruff edges so it sits flush. its just flat out safer for a novice like my students

Posted

For years I used a cordless circ for that task. +1 for the sheet of rigid insulation. (It is hard to beat the rigid insulation technique.)

Now-a-days, due to the volume of sheet goods I do, I have an outfeed, slidefeed and rearfeed set up for my table saw which allows me to skip that step all together.

Posted

I used to rough cut with a cordless circular saw or table saw and then final cut on the table saw. Last year while making cabinets for my wife's closet, I bought a Festool TS 55 and a track long enough to cut 8'. I wish I would have bought one of those a long time ago. I cut everything to size the first time and the cut is better than using the table saw. I lay a sheet of rigid insulation across the table saw and outfeed table so I can cut everything standing up.

Posted

+1 on Erics rigid foam suggestion.

The straight edge is as simple as a 4" wide strip of 3/4" ply attached to an 8" wide strip of 1/4" ply. Zip the saw down the assembly, for the final cut of the 1/4" part. You're left with a zero clearance straightedge that will show you exactly where the cut will land.

Simply line up the edge of the 1/4" bottom layer with your marks, clamp the guide in place, and cut away. Make a 4' and 8 version.

Posted

I cant believe that it took nine post for someone to mention the Festool TS55. I just bought one this week and I am completely amazed with its performance. Easy to use, cut quality is awesome, size is good, lightweight. It is a little on the pricey side, but well worth the money.

Posted

I'm sure the Festool system is stellar but I'm thinking the best application is on a jobsite where accuracy is still important but you may not have all of the tools you would have in your shop. Shops dealing with a lot of sheet goods are often set up with panel saws or side tables. The cost of Festool is the limitation. At the risk of angering all of the lovers of green, it's a circular saw with an aluminum track to guide it. Would I love to have one? Most definitely...is it worth the money?....not in my opinion. Could be that I use one and become a convert and begin saving nickels?...possibly...but as of now, Barry and Southwood have the ticket.

Posted

I think it really just depends on what your doing. If your shop is small with a tiny table saw then its pretty hard to beat a festool saw, but a regular skill saw will get the job done. If you building cabinet boxes on site then again the festool is clearly a winner. When were talking about just roughing in a shop with enough space for a full size table saw and outfeed table, then really roughing in general is a waste of time. There are those times when you just need to shorten a full sheet down a foot. I couldnt justify festool just for those few times a year. I can get just as clean of cut with a full sized worm drive saw and a hard board throat plate. The only real difference is that Im left with a mess to clean up afterwards.

Don

Posted

Rough cutting is a fact of life for basement dwellers. Sometimes, there's just no good way to get full sheets into the shop. I'm fortunate to only have to rough cut 2-3 months of the year, when snow blocks my ground-level access.

I hope all you guys and gals who can go directly from truck to table saw appreciate the access! ;)

Posted

If I only have one rough cross cut to make (note: I finish all my panels to size on the table saw so I always oversize at least 1" per dimension), I use a cordless 5-1/4" circ saw with a straight edge bar clamp. If I have several cross cuts, I'll use a corded circ saw. I support the panel on 2-2x4's laid across saw horses. This makes the plywood at a comfortable height to cut on. If I have a complex cut, meaning that I need to cross and rip to get panels out and the initial cut still makes the piece to large to use on the table saw, I'll use a corded Bosch jig saw. If my first cut is a rip cut, I can manage that with rollers and my tablesaw with outfeed table.

Posted

When were talking about just roughing in a shop with enough space for a full size table saw and outfeed table, then really roughing in general is a waste of time.

"That's a BINGO!"

Don,

You nailed it. With my table saw set up there is no need to rough cut. I can go from sheet good to accurate finished piece faster than most guys can even get out their track saw.

And, Yes, CessnaPilotBarry, I do appreciate it. I went through the rough cutting thing for years before getting to the set up I have now.

Posted

When were talking about just roughing in a shop with enough space for a full size table saw and outfeed table, then really roughing in general is a waste of time.

For me it is a matter of handling the sheet goods. Being in a wheelchair limits how big of pieces I can move around the shop. I used to use a circ saw and a shop made guide, but didn't get the accuracy that I was looking for. What I like about the Festool is the fact that it takes the play out of the cut. I don't have to worry about the saw moving off the track. I also can't make a full cut in one go. I have to stop mid cut, move to the other side and continue the cut. I wish that I could still maneuver big sheets like I used to, but unfortunately, it just isn't possible. My Now, I plan on just eliminating one of my step is sheet good work. If I can get a square and accurate first cut, then it keeps me from having to to make the extra cut on the TS(from a handling standpoint). But if I were able bodied, then I would agree with you completely..

  • Like 2
Posted

For me it is a matter of handling the sheet goods. Being in a wheelchair limits how big of pieces I can move around the shop. I used to use a circ saw and a shop made guide, but didnt get the accuracy that I was looking for. What I like about the Festool is the fact that it take the play out of the cut. I dont have to worry about the saw moving off the track. I also cant make a full cut in one go. I have to stop mid cut, move to the other side and continue the cut. I wish that I could still maneuver big sheets like I used to, but unfortunately, it just isnt possible. My Now, I plan on just eliminating one of my step is sheet good work. If I can get a square and accurate first cut, then it keeps me from having to to make the extra cut on the TS(from a handling standpoint). But if I were able bodied, then I would agree with you completely..

That would be difficult, for anything for that matter. I think i'd be using a power feeder.

Don

Posted

For me it is a matter of handling the sheet goods. Being in a wheelchair limits how big of pieces I can move around the shop. I used to use a circ saw and a shop made guide, but didn't get the accuracy that I was looking for. What I like about the Festool is the fact that it takes the play out of the cut. I don't have to worry about the saw moving off the track. I also can't make a full cut in one go. I have to stop mid cut, move to the other side and continue the cut. I wish that I could still maneuver big sheets like I used to, but unfortunately, it just isn't possible. My Now, I plan on just eliminating one of my step is sheet good work. If I can get a square and accurate first cut, then it keeps me from having to to make the extra cut on the TS(from a handling standpoint). But if I were able bodied, then I would agree with you completely..

SAC, you never cease to inspire me.

  • Like 1
Posted

SAC, you never cease to inspire me.

Where there is a will, there is a way..... usually....

That would be difficult, for anything for that matter. I think i'd be using a power feeder.

Don

Interesting concept.. Never thought about that.. hmmmm.smiley-think005.gif

Posted

Where there is a will, there is a way..... usually....

Interesting concept.. Never thought about that.. hmmmm.smiley-think005.gif

Powerfeeders are great on the table saw. A buddy of mine uses them on every tool in his shop. Never had and accident in 35 years of owning a 25 man cabinet shop.

Don

Posted

For me it is a matter of handling the sheet goods. Being in a wheelchair limits how big of pieces I can move around the shop. I used to use a circ saw and a shop made guide, but didn't get the accuracy that I was looking for. What I like about the Festool is the fact that it takes the play out of the cut. I don't have to worry about the saw moving off the track. I also can't make a full cut in one go. I have to stop mid cut, move to the other side and continue the cut. I wish that I could still maneuver big sheets like I used to, but unfortunately, it just isn't possible. My Now, I plan on just eliminating one of my step is sheet good work. If I can get a square and accurate first cut, then it keeps me from having to to make the extra cut on the TS(from a handling standpoint). But if I were able bodied, then I would agree with you completely..

Honestly Sac when I commented, I hesitated because I thought of you. Control of the tool for anyone is important and the track gives that. Anyone who has used a circular saw for any length of time has had a kickback so I'm not throwing rocks on the track saw---like I said, I'd love to have one-- it's just pricey. I think Chet speaks for all of us - you inspire us.

Barry...."snow blocks my ground-level access" ...I can't even imagine. Three inches of snow in SC and the world stops. Schools close and the ER fills up from rednecks doing things worthy of Youtube...BTW, the screw in my shoulder is only 2" long...not as bad as some. :blink:

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 50 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined