Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Just about to buy a new TS - what tools for setup?

Featured Replies

Ok, I'm preparing to drop some money on a new Table Saw, and I want to make sure that when it arrives, I have all the tools I need to do setup. It should be a 3-4 hour job, not 3-5 days to collect tools once it arrives...

I have wrenches and screwdrivers for assembly, but I'm concerned about tools for calibration. I want to dial my new TS in as perfectly as I can get it.

I already have some mineral spirits and T9 for cleaning and prepping the table top. I think I still need some wax. Mark suggests Renaissance wax. Do I need wax on top of T9?

Also, I have a kind-of-ok straight edge (Bostitch 29" level)... which would help when attaching the wings... but would a dial gauge be better?

I have a digital caliper, but those aren't self spring-loaded like a good dial gauge would be for be measuring blade-to-miter slot alignment. Should I get one first?

What other tools would I want to have ON-HAND to get a TS ready to go?

A straight edge will be fine a long as it is straight. Marc has a video on tablesaw tunning that is very good.

Also, it helps if you have someone to put the wing bolts in finger tight while you support the weight.

The T9 Boeshield protects the top, while the wax helps make the surface nice and slick, so I would wipe the top off with mineral spirits first, then apply the T9, then apply the wax.

On the wings, a nice trick is to get a perfectly flat block of wood on each and put it halfway on the wing, halfway on the table, then clamp both sides down, that should considerably help get those aligned.

I tune my fence with a pair of digital calipers, there is some sort of miter gauge attachment (cheap, Woodcraft has them) that you can attach those things to. Not as good as those fancy gauges, but as long as you get a similar reading on both ends of the miter slot, you should be good.

Otherwise, a rubber mallet might be helpful in aligning the table top to the blade / arbor.

I want to make sure that when it arrives, I have all the tools I need to do setup.

Besides wrenches and screwdrivers and mallets and such, I suppose all you really need is a combination square to get the blade and fence parallel to the miter slots, and the blade square to the table. Marc's video on table saw setup shows how this works.

Having said that, I think you will be a lot more confident in your setup if you spring for a dial indicator. Also, you will find yourself using it for all kinds of things once you have one. I have both of the following, and they both work just fine:

http://www.harborfre...icator-623.html

http://www.grizzly.c...s-Special/G9849

I would not personally buy a fancy kit like Nben suggested. You can do all the same sorts of things with a basic dial indicator and some simple, shop-made jigs. I think you would be better off to spend the $200 on a couple of high-quality saw blades, or maybe some wood to make an outfeed table and a crosscut sled.

-- Russ

I found these to be very helpful in setting up and maintining my saw:

http://www.woodpeck.com/sawgauge.html - adjustment of the fence and miters.

http://www.leevalley.com/us/wood/page.aspx?p=56676&cat=1,240,45313&ap=1 - a good straight edge

http://www.wixey.com/anglegauge/index.html - setup the stops and adjust the angles.

Just a few things I have gotten a lot of good use out of.

-Gary

If you have a four foot level and a combination square is all you need for calibration, or like Don says the factory edge of some plywwood will work for a straight edge. When I put the wings on my unisaw just last month I just sat them on two outfeed stands just put a little plywood cap over the rollers just three pieces of scrap. I put it together myself it was pretty easy, and I'm old. I'm sure you already have everything you need now.

It's nice to get the wings as flush and level as possible (use shims if necessary), but don't go too nuts worrying about the top being absolutely perfectly flat....it just needs to cut well. It'd take a sizable deviation from flatness to effect the cut. Ditto on the combination square...it's a quick easy tool for getting the blade alignment pretty darn close to perfect. Use the miter slots as a reference... align the blade up parallel to the slots, then adjust the fence parallel to the blade.

The trick with T-9 is to use a very light coat, and wipe it down after. Let it dry, then apply the wax....lots of paste waxes are fine. Minwax, Johnsons, etc....no silicone.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.