patriot Posted September 5, 2012 Report Posted September 5, 2012 Let me start by saying I have zero experience with pneumatic tools. I recently picked up a small pancake compressor for the garage/shop. I was planning getting a small nailer to go with it. Right now, my main interest is in being able to use it for nailing/pinning parts together for jigs and such. Based on what I've read so far I believe a brad nailer (@ 18 gauge) will meet my needs. I'll primarily be working with 1/2" or 3/4" ply or mdf. Will the 18ga brad nailer do what I need or should I step up to a finish nailer? Any other general tips/suggestions in selecting? My woodworking interests are primarily furniture and a little bit of cabinetry. Thanks! Quote
jimmykx250 Posted September 5, 2012 Report Posted September 5, 2012 Buy a combo kit the has the finish nailer and the brad gun, you will find you use both. I have had great luch with the porter cable guns. Quote
tim0625 Posted September 5, 2012 Report Posted September 5, 2012 I bought the Dewalt combo kit from Home Depot with a 16 & 18 gauge gun and have been very satisfied. I'm a little sketchy about off brands and the availability of nails so I went with the brand name. I 'm sure Porter Cable is a good one too. Hey, Norm uses it! As far as the 'no experience', easy greasy...just keep your left hand out of the way...through the years, I've had some near misses that definitely increased the pucker factor. Quote
Andrew Pritchard Posted September 5, 2012 Report Posted September 5, 2012 I've got a cheap as you like "off brand" compressor and nailer/stapler gun at 18 gauge. I've found it incredibly useful, both in my home renovations and in the shop. I like it so much, I'm considering buying a 16 gauge nailer. I'll probably go with Campbell Hausfeld again as I've found it reliable enough for my needs. I've had no problem finding nails or oil for it - Paslode do a very nice pack with varying lengths and I've never had a problem with the fit. I agree with keeping your off hand out of the line of fire. As with all powertools, it doesn't know when it's going to cut/staple/drill etc something it shouldn't! Watch the angle you're using it at, especially if you're using longer nails as the nail can bend inside the wood and come out in an unexpected location. Found that one out the hard way. I had a nail skim my left ring finger, which tore a neat 18 gauge hole in the my nail. Quote
Texfire Posted September 5, 2012 Report Posted September 5, 2012 And resist the temptation to set up an improvised shooting gallery by setting up soda cans on the opposite wall and holding the safety back manually. Lessons from a misspent youth in the Theatre shop. 1 Quote
fransikaner Posted September 5, 2012 Report Posted September 5, 2012 And resist the temptation to set up an improvised shooting gallery by setting up soda cans on the opposite wall and holding the safety back manually. Lessons from a misspent youth in the Theatre shop. Ah the memories of sitting on a roof after a hard day's work with a beer and a framing nailer............... Quote
TRBaker Posted September 5, 2012 Report Posted September 5, 2012 Patriot, I build a lot of cabinets and shop jigs and I find that I use both guns equally as much. There are times when you just need the larger head of the finish nail, and the extra beef to pull things together. Quote
rodger. Posted September 6, 2012 Report Posted September 6, 2012 You may also want to consider getting a 23 guage pin nailer - great for various tasks! Quote
wdwerker Posted September 6, 2012 Report Posted September 6, 2012 $25 for a 23 gauge micro pin gun at Harbor Freight , just like one I found at a flea market. Shoots up to 1 inch pins. A dealer at the IWF wood show this year told a tale of being shot in the crotch by a carelessly handled pin gun. Yes... a 2 inch pin to the head! So watch where you point those things! I found a new tool at IWF. Nailjack pliers! Work great at pulling air nails and staples! Quote
AceHoleInOne Posted September 6, 2012 Report Posted September 6, 2012 I second the little 23G pinner. I found a Freeman for stupid cheap. Really a great little nailer. Use it all the time. Quote
Boatworks Today Posted September 6, 2012 Report Posted September 6, 2012 My most used gun is the micro pin nailer. I use it to hold things together while glue is drying allowing me to handle the piece and keep moving. A very nice feature of the micro nailer is that there is very little (if any) sign that it was nailed (it's that small) BUT surprisingly the pins have a pretty strong grip. Quote
Trip Posted September 6, 2012 Report Posted September 6, 2012 ==> My most used gun is the micro pin nailer. +1 -- 23g is great... also consider 21g. i got the 21 after using the 23 for a while. the 21 is actually a bit more useful -- with heads, it has pretty decent holding power.... with headless, it is almost as invisible as 23g. Quote
wdwerker Posted September 8, 2012 Report Posted September 8, 2012 We check to see if there are micro pins in something before cutting it with a powerful magnet, if you sand the tiny hole fills with dust, no way to tell otherwise. K & J magnetic sells ball magnets, 1/2 dia will find nails in drywall, hardwood floors and even tiny 3/8 long micro pins! I keep a ball magnet stuck to my Leatherman every day. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.