Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

shop vac muffle box

Featured Replies

i am planing on building a muffle box for my shop vac. the sound is killing me having it run for a half hour while i use my carving tool. i am basicly building this

http://home.comcast....vacsilencer.htm

anyone got any recomendations for good sound deading insulation that i can get cheap? i want the best for my buck with little cost.

what would be a better box mateiral mdf or plywood to help deaden the sound.

Jusy an fyi sears makes a muffler that plugs into the discharge port. It helps alot. I bought mine years ago but im sure they still sell them. I do like your box idea I just dont have that kind of room in my shop.

  • Author

neither do i but i got to fit it in between my ears ringing and the family complaining its got to get done or else i go to doing only chisel and knife carving and i don't like that its too boring and slow. the boxes seem to work really well cutting a 90 db machine to 50 db most conversations are 60

Duck, do you run into heat problems when enclosing the vac?

As for good sound proofing on the cheap, drywall or sheetrock actually absorbs a lot of sound. I used double sheet rock on a dummy wall in my shop, and placed the DC on the other side. It is a very tolerable hum now instead of the painful roar it created on the shop side of the wall. I would think a single sheet of 5/8 rock would take care of it for <$10.

I would watch the temperature. Some air holes high and low with baffles of insulation might be a good idea. Once you get it figured out check the interior for dust build up regularly.

I have a Fein vac that is pretty quiet, but it has a lot of foam rubber baffles that get clogged up with dust and it starts getting hot.Take it apart and blow all the dust out and temperature falls.

Check music equipment sales or repair locations and see if they have old used sound foam sheets or foam from road cases for instruments . Check Craigslist for used" egg crate" foam mattress topper.

I was concerned about heat as well, and was going to recommend an inlet vent with baffles, and a fan to pull cool air in. The air would leave through the same outlet vent that the vacuum uses. Then I thought, "we've already got a motor that is pulling shop air in and past the motor. That's what the shop-vac does."

Very cool design. I would try a local arts/crafts supply store, or even target/walmart, for some sort of foam.

I guess to minimize the floorspace required you could build it taller so the exhaust baffles would be on top instead of off to the side. And, with the hose connector and power switch on the side it could actually double as a tool stand or mobile cart. I need to make some mobile bases for a drill press and small bandsaw, and now I'm considering using this design so I can hide the shopvac in the base.

If you were worried about heat, and wanted some circulation in the actual box, you could put a small diverted damper off the blowing port that goes into the box. Just a thought.

The air coming out of a shop vac is already warm. I tried using the shop vac exhaust to blow into my router table base to keep the dust moving, it worked but quickly got too hot for the router motor. Going to try a large computer fan next.

  • Author

here is one that a guy made im baseing it off this with a little taller room on top so i will have room for the air to cool around it. i also will have the baffels slide out so those will catch any light dust and i can just suck up any light dust that ended up coming out of the machine.

The air coming out of a shop vac is already warm.

The way I see it, the air coming out of the shop vac was room temperature when it was pulled into the shop vac, then it was used to cool off the motor, and that's why it is warm coming out of the shop vac. So, the muffler box has a steady stream of room temperature air being pulled in, run past the motor to cool the motor and warm up the air, and then the warm air exits the muffler box through the baffled vent.

It might be that the shop-vac needs to be surrounded by room temperature air in addition to the room temperature air being sucked in through the hose. But I think the ambient air would have little affect compared to the stream of fresh air being pumped by the vacuum.

  • Author

http://www.startwood...e-your-shop-vac

im thinking if i leave plenty of open space around the motor on top where air will be vented that there wont be that much of a heat build up. i found one guy who said he left his on for a couple days and it burned out his motor. he said it was so quiet that he didnt realize it was still on. it gets warm but i think if it has a way to get air out that it will not have a heat build up. now if it was a air compressor i think i would have to come up with some kind of fan to keep it cool since compresing any molicules always creates heat.

http://www.finewoodworking.com/workshop/video/build-a-simple-box-to-muffle-your-shop-vac.aspx

this is probably the best example that i have seen of this type of concept.

  • Author

what about attaching an actual small car muffler to the box?

There are two different types of shop vac motors, bypass and pass through. Bypass motors are used in wet/dry vacs and rely on separate air for cooling because of the moisture. On a vac that is dry pick up only, a pass through motor is used and moves the filtered air over the motor to cool it.

If your vac is a wet/dry model I would not put it in an enclosure, go buy a dry pick up only and use it.

I personally would not line the entire case with foam, as that will only insulate the cavity and increase the temperature of the air inside it.

Going off theory, the car muffler works to dampen the noise by routing the air back and forth in the resonator chamber. I'd go off the second design for this, rather than the first with the foam, although I really like that switch on top. (Maybe add a small LED indicator to show it's on? Or use a lighted switch...)

If you're going the foam route, look for eggshell foam, or open cell foam. You might be able to find some in camping supplies, although most camping foam mats will be closed cell for the insulation factor. The other option is to look for things like knee rests for the gardener or yoga mats. I'd think the eggshell would be cheaper and easier to find, though, as Wally world, JoAnns, Michaels, and most craft stores have a version of this somewhere.

  • Author

There are two different types of shop vac motors, bypass and pass through. Bypass motors are used in wet/dry vacs and rely on separate air for cooling because of the moisture. On a vac that is dry pick up only, a pass through motor is used and moves the filtered air over the motor to cool it.

If your vac is a wet/dry model I would not put it in an enclosure, go buy a dry pick up only and use it.

its a dry vac already looked into that :)

I personally would not line the entire case with foam, as that will only insulate the cavity and increase the temperature of the air inside it.

Going off theory, the car muffler works to dampen the noise by routing the air back and forth in the resonator chamber. I'd go off the second design for this, rather than the first with the foam, although I really like that switch on top. (Maybe add a small LED indicator to show it's on? Or use a lighted switch...)

If you're going the foam route, look for eggshell foam, or open cell foam. You might be able to find some in camping supplies, although most camping foam mats will be closed cell for the insulation factor. The other option is to look for things like knee rests for the gardener or yoga mats. I'd think the eggshell would be cheaper and easier to find, though, as Wally world, JoAnns, Michaels, and most craft stores have a version of this somewhere.

i think im going to put the foam on it and put a thermomider inside it and keep track of it. leave it run for a couple hours and check the temperature ever 10-15 min or so. if the temperature does not raise to much and instead the temp goes out the resonator chamber and bounces off the baffels.

Buy yourself a mini fridge and use that as your enclosure. It will stay nice and cool in there and a frig is pretty sound proof.

Buy yourself a mini fridge and use that as your enclosure. It will stay nice and cool in there and a frig is pretty sound proof.

Genius idea! Might have some higher operating costs but you could shut it off when you aren't running the vac. Gasket on the door, insulated and manufactured in volume... No additional materials costs, no time involved building a case, just drill a few holes.

Check music equipment sales or repair locations and see if they have old used sound foam sheets or foam from road cases for instruments . Check Craigslist for used" egg crate" foam mattress topper.

The name used in the acoustical field is convoluted foam. It's open cell versus the closed cell construction of the mattress topper. That means it will absorb more sound as well as retain less heat.

I was concerned about heat as well, and was going to recommend an inlet vent with baffles, and a fan to pull cool air in. The air would leave through the same outlet vent that the vacuum uses. Then I thought, "we've already got a motor that is pulling shop air in and past the motor. That's what the shop-vac does."

Yes but if the sound baffles restrict the airflow out in an attempt to reduce sound that's where the problems start with overheating.

  • Author

ok got the box built with no insulation yet. the temperatures hovers around 80-85 degrees. i piped the air down towards the exit with just a angled pvc pipe. there is a good steady flow of air coming out the back. anyone have a idea at what temperature a shop vac will over heat at? it has cut the volume a bit but not enough so i will need to add in baffles and and insulation to get the best benifit out of this desighn. oh and thats from measuring the temp from right on top of the motor. just set the thermometer on top of the shop vac.

Compare that to the temperature right on top of the motor without the box. If they are the same, then the box isn't causing the motor to overheat.

As long as the temperature stays below 90, I think you are good. After all, if you were working outside on a 90 degree day you wouldn't say, "I better not run the shop vac - it might overheat."

  • Author

never thought to measure the temp outside the box going to go set it out right now and see what it does.

  • Author

stays around 60 outside the box......just went and looked at the shop vac even though its not a wet/dry it is a bypass motor. looks at the instruction book rather then asuming that just because its a regualr vac it must be a pass motor. damn i might have to buy a new shop vac now. think ill line it with padding of some kind first and then decide if its worth geting a new shop voc for this. anyone got any idea how i can possibly vent some air into the box? so i dont have to get rid of my shop vac. maybe some computer fan?.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.