wdwerker Posted July 27, 2013 Report Posted July 27, 2013 I just got a email that 2 tools I ordered last night are being delivered Saturday morning! I expected delivery on Tuesday. CPO websites have treated me well on quite a few purchases. I ordered a little12 volt cordless Bosch impact driver and a Sawzall to make a tough project possibly run a bit smoother. I have to renovate/ restore a 1950's mid century modern staircase. Douglas fir 4 x 10 beams knotched for the stringers, 2 x 10 treads and open risers. Besides being beat up the rise and run is a mess. Each step is a different height and width. Already made a batch of new treads. Next week I have to remove a tread then cut the stringer to the correct height and install a new tread, that's where the Sawzall comes in. Original was nailed and screwed down, we are going to use 3 1/2 screws, thus the impact driver. I have a 30 year old Sawzall that still works but there is a good bit of slop in the mechanism so I didn't trust it to make so many accurate cuts. Quote
Spencer_J Posted July 27, 2013 Report Posted July 27, 2013 sounds like a great challenge! I am excited to see how the Sawzall tool works for your application. please take some pictures if you can of the job! impact driver will be a joy. Quote
tim0625 Posted July 27, 2013 Report Posted July 27, 2013 Hey Steve! How about some pictures before, during, and after? This could be big for you too if you show another customer the types of work you do. I'd love to see them! Quote
Tom King Posted July 27, 2013 Report Posted July 27, 2013 This is not intended as any sort of criticism-just how I'd do it. I'd probably cut the stringers with a handsaw, if there is room or the stringers are to be taken down. If the screw holes are going to be plugged, I'd recommend the "star drive" Deckmate screws available in Home Depot. Since I used them the first time, they are always my first choice. I'd also like to know how the 12v driver does with 3-1/2" screws. For anyone who has never built stair stringers before, remember that the bottom riser needs to be less the thickness of a tread when figuring rise and run to lay out the stringers. If you don't allow for the tread thickness on the first riser, the first one will be different (higher) than the rest of them. Not applicable here, since this is a modification to existing stringers, but either use stair gauges that clamp onto a framing square, or lacking those, clamp a board to the square when laying out the stringer on the board to start with. Cut one the best you can, and use that one as a pattern to mark the rest of them. Figure the top attachment so you can lay a long straightedge on all the steps, and it hits every one. You run across many staircases where the top step is different than all the rest because it was not factored in. Total rise and run should equal between 17 and 17-1/2 inches, with rise between 7 and 7-1/2 inches when laying out new ones. Some situations require cheating the "ideal" proportions, but it's a good guide-for instance on our dog porch, I used 5" rise so puppies could easily go up and down. I used 12-1/2"" run, and they walk fine for people too. Quote
wdwerker Posted July 27, 2013 Author Report Posted July 27, 2013 We did one tread as a test run. I was impossible to get all the metal out of the wood so I used a nail embedded wood cutting blade in my old Sawzall. It was hard to get a flat smooth cut so I built a jig to clamp to the stringer to guide the saw blade. I even covered the top of the jig with laminate to provide a harder wearing surface. We carefully measured the rise and run of each stair and then did a lot of math. Each step has to be re-cut so that they will all be the same after we install the new treads. 5/16 to 7/8 range in the amount I have to cut off plus several treads were not level, so I am going to level my jig, cut, level the jig on the other stringer and cut. I will be taking pictures but it is hard to post pictures on the forum from an iPad. Might have to figure out how to post a link. Quote
Tpt life Posted July 27, 2013 Report Posted July 27, 2013 I have never had a clean enough cut with a sawzall to leave it exposed. To minimize tear out you often have to clamp sacrificial stock on either side. Have you considered milling a recess into the bottom of your treads or will there be some type of shadow trim covering the joint? Quote
dwacker Posted July 27, 2013 Report Posted July 27, 2013 I will be taking pictures but it is hard to post pictures on the forum from an iPad. Might have to figure out how to post a link. Attaching photos on an ipad is the same as your pc. Except you use the more option section not the quick post section if that makes any sense. When you tap on choose photo you pic from your camera roll or can shoot a new one with the ipad camera. Quote
wdwerker Posted July 27, 2013 Author Report Posted July 27, 2013 I have never had a clean enough cut with a sawzall to leave it exposed. To minimize tear out you often have to clamp sacrificial stock on either side. Have you considered milling a recess into the bottom of your treads or will there be some type of shadow trim covering the joint? The jig will provide some backup/support and the 4 x 10 beams are pretty rough. Plus the whole thing is painted semi gloss black so there will be caulk and tons of shadows. Oh and I forgot to mention the walls 5 " away are covered in mirrors! We made blocks to cover the riser cuts and extend the support for the treads, so all the exposed surfaces will be new wood and well sanded. Thankfully the clients painter is doing all the finish work. I spray fine finishes in my shop but detest painting onsite with a brush. Quote
Trip Posted July 27, 2013 Report Posted July 27, 2013 ==> I ordered a little12 volt cordless Bosch impact driver i've got that one -- it's a sweet little driver. I've also got their 18v driver for more 'serious' DIY activities -- highly recommended. Quote
Freddie Posted July 27, 2013 Report Posted July 27, 2013 I also have the 18v combo kit that i use for work. I also bought the bosch radio so now i have three batteries to swap out on the job. Those guns get abused, and they stand up to it. Quote
G S Haydon Posted July 27, 2013 Report Posted July 27, 2013 I have never had a clean enough cut with a sawzall to leave it exposed. To minimize tear out you often have to clamp sacrificial stock on either side. Have you considered milling a recess into the bottom of your treads or will there be some type of shadow trim covering the joint? An addition of a scotia under the tread can hide a multitude Nice to see the variety of Jobs you do Steve, this one sounds fun. Quote
Tom King Posted July 27, 2013 Report Posted July 27, 2013 That sounds like a job I would have turned down. Quote
Spencer_J Posted July 27, 2013 Report Posted July 27, 2013 Me too tom! Steve is a trooper for certain! Quote
wdwerker Posted July 28, 2013 Author Report Posted July 28, 2013 Tools came in today! Impact driver is going to be a big help. Blade change on the new Sawzall is very easy. You can rotate the "D" handle of the saw and it locks every 45 degrees, just the ticket for close quarters work. I only tackle projects like this for nice clients who will pay for the time and effort required. We have done quite a few jobs for this lady and she has been great to work for. 1 Quote
Tom King Posted July 28, 2013 Report Posted July 28, 2013 That makes sense. I've worked years over several decades for one family, and wouldn't turn down that sort of job from them either. Anybody else...a different story. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.