nod Posted February 19, 2014 Report Posted February 19, 2014 ok, i'm at it again. I've learned so much just reading the forums here, I am turning to you again for help. (I've decided to hold off on RAS or SCMS until I replace the table saw first). I've been looking at some used saws. Trying to keep the budget at $500 or less. Locally, a Powermatic 64A just popped up. Or, I'm curious about this Jet gold series with router extension. I think the jet is overpriced but what do I know? My only assumption is that it's decent is because of the Xacta fence. From the forums I've learned that's the one to go with if possible on the jets. It has a full cast top vs others I've seen with stamped wings. Are these saws comparable? If the jet were 500, would it be a fair price? Seems like lots of price dicussions on these forums are all over the place. Well, here in the Bay Area, prices are higher for everything, that's for sure. If either of these are worth looking at, picking up, negotiating over, I sure would appreciate the help. I've got a few bucks burning a whole in my pocket and a hankering to cut some wood. Quote
Dave H Posted February 19, 2014 Report Posted February 19, 2014 The powermatic's damn near 3000 new I doubt you could beat him down to much on price, I would want to look at it and, hear the motor run. The Jet contractors saw is about 650 without the router table so I think the guy on graig's list is asking to much. Quote
pghmyn Posted February 19, 2014 Report Posted February 19, 2014 The powermatic's damn near 3000 new I doubt you could beat him down to much on price, I would want to look at it and, hear the motor run. The Jet contractors saw is about 650 without the router table so I think the guy on graig's list is asking to much. $3000 for the contractors saw? I see them online for $1700. Even then, still not a bad price assuming everything is in working order. Quote
nod Posted February 19, 2014 Author Report Posted February 19, 2014 thanks. I've emailed both and waiting for some replies. Missed out on another jet (no router table) that was 375. I was ready to jump in the car, but hte guy said it sold. At that price, I'm sure it went fast. Quote
nod Posted February 20, 2014 Author Report Posted February 20, 2014 well, looks like it's a non-issue. I had emailed the guys pretty quick, but had not heard anything. went back to hte powermatic post and it was deleted. obviously sold. Seems like the good saws (and good deals) are going within hours. Of course if I had 1200-1500 to spend, there are plenty of PM 66's, Unisaws and the like. Quote
jimmykx250 Posted February 20, 2014 Report Posted February 20, 2014 Due to this lovely recession we cant seem to climb out of America is having one huge garage sale for the last few years. Keep your eyes peeled and dont settle but you will find what your looking for eventually. Quote
nod Posted February 20, 2014 Author Report Posted February 20, 2014 Due to this lovely recession we cant seem to climb out of America is having one huge garage sale for the last few years. Keep your eyes peeled and dont settle but you will find what your looking for eventually. I was just thinking I had missed my window by a year or two. In the bay area it's bounced back a fair amount. My area is ok, but SF has had an insane boom. I'm even looking at towns further out than I would normally drive due to just this effect. Not that I want to take advantage of anyone, but I do want a deal. Thanks, and I will do just that. take my time and get the goods. I wish I had a few extra bucks to buy that fancy cabinet saw, but who am I kidding? I don't need that much for what I'm looking to do (of course, famous last words). I try and follow the, "buy the best you can" philosophy. But I'm a weekend warrior at best. I have too many hobbies as it is. 1 Quote
knotscott Posted February 20, 2014 Report Posted February 20, 2014 Aside from the grated wings, this old Delta is pretty similar in class to the PM64a and the Jet you missed out on....it looks to have a Unifence. This Ridgid at $250 has potential too.... Quote
Spencer_J Posted February 20, 2014 Report Posted February 20, 2014 any used saw from a production environment should be inspected carefully. my '69 unisaw came with a cracked front bracket which i was advised about before purchasing but limits my bevel accuracy. i'll get a new one on ebay some day when i find the time. additionally, there was so much caked on sawdust that i could not see the bent top of the cabinet which showed a serious drop at some point in it's life. i could have gotten a better price if i had really checked that thing out. also, motor bearings and arbor bearings are a good thing to check out/ sound when you take a look. one thing that i did when i was looking for a used TS was put a wanted ad on craigslist explaining my perimeters. i received a ton of legit emails and calls from people who had some good stuff for sale that normally wouldn't post onto craigslist. if there are any woodworking stores or communities around locally, put the word out, some have bulletin boards etc. check out ebay too, there are tons of TS on there. so many people have great equipment that they hardly use just collecting dust. buying used is a great way to get some sweet equipment for the right price. Quote
nod Posted February 20, 2014 Author Report Posted February 20, 2014 Aside from the grated wings, this old Delta is pretty similar in class to the PM64a and the Jet you missed out on....it looks to have a Unifence. This Ridgid at $250 has potential too.... Thanks for the tip. I have seen that old delta (there seem to be quite a few out there), it's just that distance is a bit too far. The Ridgid price is very nice. I wasn't too sure what folks have thought about Ridgids? anything is going to be an upgrade, but is it a worthwhile saw? I heard back from the guy selling the Jet with the router extension. Of course, I've watched 2-3 similar saws (full cast iron tops) sell for 375-475 very quick. This 600 version is still around, which I can only attribute to price. I emailed the fella back, he can show it tomorrow, so we'll see. btw-he mentioned it's 10-12 years old. I know i'm looking at used saws here, and most are at least that old if not older, but anything going to wear out in that time that would stick out? Quote
Rick A McQuay Posted February 20, 2014 Report Posted February 20, 2014 I'm still seeing the Powermatic ad but if he doesn't reply then it doesn't matter if the ad is up or not. Quote
nod Posted February 20, 2014 Author Report Posted February 20, 2014 so many people have great equipment that they hardly use just collecting dust. buying used is a great way to get some sweet equipment for the right price. Thanks for the tips. all great sounding which I'll look into, a few of those I had never thought of. the woodcraft and rockler aren't exactly close (only shops like that around here i know of), but would be a worthwhile afternoon. thanks again. Quote
nod Posted February 20, 2014 Author Report Posted February 20, 2014 I'm still seeing the Powermatic ad but if he doesn't reply then it doesn't matter if the ad is up or not. noticed that. weird. It was down yesterday, but this post shows it as a recent listing. Anyways, sent another email for shiggles. see if there's a response this time around. anyone looking for a badnsaw should check out THIS beast that caught my eye. of course i have no space and funds for such a thing. Who doesn't love large old school machinery. looks like something that would end up in Frank Howarth's shop Quote
nod Posted February 20, 2014 Author Report Posted February 20, 2014 Good news I suppose... The seller of the Powermatic had some scam emails which is why she took the ad down. the ad is back up, and we're going to take a look at it Saturday morning. Sounds like a friend of hers left the country and she bought his tools. Now she's looking to clear some space. If she's correct, it's had very little use in it's life, mostly collecting dust. She has the manual as well. I see in the pic there is no throat plate, so those would need to be purchased/made. I don't see a miter guage either. hmm... She also has a delta 13" planer (22-580) that looks practically new. Is this a worthwhile tool? most guys I know opt for the dewalt version in this size. Just wondering if there's some bundle pricing i might be able to get. She mentioned that too, so it sounds like she'd love to see the lot go. Quote
knotscott Posted February 21, 2014 Report Posted February 21, 2014 My Delta 22-580 worked great. I'd think $250 is a fair price. Re: the PM64a...stock miter gauges are generally junk, and you'd want a good ZCI anyway. Neither are much of a loss IMO. Quote
nod Posted February 21, 2014 Author Report Posted February 21, 2014 My Delta 22-580 worked great. I'd think $250 is a fair price. Re: the PM64a...stock miter gauges are generally junk, and you'd want a good ZCI anyway. Neither are much of a loss IMO. thanks for tip on Delta. yeah, I'm considering those more or less negligible. Quote
nod Posted February 21, 2014 Author Report Posted February 21, 2014 ok, both saws still avail. scheduled to see each to view/buy on Saturday. PM64a - $450 - not sure how firm/flexible on price. just saw - no miter, throat plate (see above), but has manual. low usage. jet gold - $600 - guy's pretty firm on price. HAS - Xacta fence, mobile base, router plate, manual, various plates, upgraded belt, piping for dust collection. + more usage, but doesn't sound overdone. right there the jet has the upgrades added in to justify the extra price (over the PM), & i agree 600 is a bit higher than I think it should be. BUT, is there any major differ in the base saws? is the Xacta fence better than the Accufence? by much? adding mobile base and router and/or ZCI, nice miter, etc will set me back a couple extra hundred. I think I'm too excited. any reasonable last chance advice here? Quote
Rick A McQuay Posted February 21, 2014 Report Posted February 21, 2014 No actual experience with Jet fences but I've often read they are good but not great. The Powermatic looks like a deal. Inserts are easy to make and I prefer my sled over the gauge anyway. Back a few years ago Powermatic made quality machines, probably all imported now. Is the 64A a US made saw? Quote
Spencer_J Posted February 21, 2014 Report Posted February 21, 2014 i don't know the specific makes and models of these two particular saws but powermatic and jet have been brands of the same company for a long time. my take on them is powermatic being the more "woodworker centric" brand and jet being the more "industrial centric". sounds like the jet is hopped up. keep in mind that hopping up your own saw is a great learning experience. it's up to you! i'm going to assume that both of these contractor saws have the same motor but if one is bigger, i'd prefer the bigger motor. if the planer is attractive to you, you should definitely bargain! in my neck of the woods, a lower offer is almost always accepted, unless it says PRICE IS FIRM, etc. i try to be respectful and make eye contact. it's amazing how far those two will get someone.... No actual experience with Jet fences but I've often read they are good but not great. The Powermatic looks like a deal. Inserts are easy to make and I prefer my sled over the gauge anyway. Back a few years ago Powermatic made quality machines, probably all imported now. Is the 64A a US made saw? +1 Quote
knotscott Posted February 21, 2014 Report Posted February 21, 2014 PM is WHM Tool Group's premium line, but in this case, the Jet contractor saw and PM64a are very similar in class, duty ratings, and design....likely from the same Taiwanese factory. Check the motor plates for the amp rating....at one time, I thought the PM64a had an 18 amp motor. AFAIK, the PM Accufence and Xacta II are both made by HTC....all pretty much the same fence. Having owned both a Biese Commercial fence and a Jet Xacta II, I'd rate the two to be very comparable....both fences are made in the USA too. Quote
nod Posted February 21, 2014 Author Report Posted February 21, 2014 if the planer is attractive to you, you should definitely bargain! in my neck of the woods, a lower offer is almost always accepted, unless it says PRICE IS FIRM, etc. i try to be respectful and make eye contact. it's amazing how far those two will get someone.... +1 Pretty sure both saws are Taiwanese. The planer could be a nice addition if I could get a bundle price that's favorable. If not, I may just do the PM since it's closer. It's only 10 minutes away vs an hour. All things in, I can spend 150-200 bucks to make the PM essentially the same set up as the jet (and end up at the same price). The jet guy said he was pretty firm, but then again, cash in hand could change that. My guess if any, he's only going down 20-50 bucks. not 100 which would make me very tempted. PM is WHM Tool Group's premium line, but in this case, the Jet contractor saw and PM64a are very similar in class, duty ratings, and design....likely from the same Taiwanese factory. Check the motor plates for the amp rating....at one time, I thought the PM64a had an 18 amp motor. AFAIK, the PM Accufence and Xacta II are both made by HTC....all pretty much the same fence. Having owned both a Biese Commercial fence and a Jet Xacta II, I'd rate the two to be very comparable....both fences are made in the USA too. Knot, i'll look when I get there. Sounds like fences, everything else is pretty much a wash. As for same factory, I wouldn't doubt it! Anyway, guess at this point I just have to check them out to be sure. thanks everyone for the help. Quote
nod Posted February 23, 2014 Author Report Posted February 23, 2014 Scored the powermatic for $400. pretty satisfied with that given what the market has to offer around here. Practically new condition. I'll post some pics once i get 'er set up. thanks everyone for all the help. btw-first page of manual.. "jet corporation". so yeah, no doubts those machines are practically the same. Quote
knotscott Posted February 23, 2014 Report Posted February 23, 2014 Should make for a solid performer for $400....congrats! Quote
wtnhighlander Posted February 23, 2014 Report Posted February 23, 2014 Does it come with flames on the side? He who dies with the most tools ... leaves a great estate sale. 1 Quote
Spencer_J Posted February 23, 2014 Report Posted February 23, 2014 sweet!!! i'm pumped for you! can't wait to see how you deck it out. i went with lee craft ZCI's when i first got my table saw because i had a big job that came up suddenly and i saw 0 time to make my own ZCI... since owning a handful of the lee craft i doubt i'll ever make my own that are that sophisticated for $22... Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.