Jenana Posted March 28, 2014 Report Posted March 28, 2014 Hello! As you may gather, I am a complete newbie when it comes to woodworking. I've always been intrigued by it and when my boyfriend also expressed interest, I bought a Makita 2705. This is the first experience I have had with a table saw and so while I don't have a basis of reference, the rip fence seems to, well, suck. When sliding it towards and away from the blade, it doesn't slide parallel and so we spend a lot of time with the tape measure making sure that it's even. I'm not sure if that is normal for all rip fences or if the one that comes stock is just poorly made. If it's the latter, due to my (lack of) skill level, I'd rather purchase something of quality vs try to use the existing one to to build one. I'm looking for help because I need to know, first, if there IS a better option, and secondly, what the heck to search for! Any assistance would be greatly appreciated. Jenny Quote
Dave H Posted March 28, 2014 Report Posted March 28, 2014 I tried to find the manual for this saw on line but, didn't have any luck but I'll bet if you look in your manual that came with the saw there will be some kind of adjustment screws. That will make the fence parallel to the blade good luck hope you figure it out. Quote
EdgewaterWW Posted March 28, 2014 Report Posted March 28, 2014 (edited) Welcome to the forum!Sorry for the bad news but, any table saw with the description "Contractor (edit--should say jobsite) Table Saw" really is not good for woodworking.I have never seen one with a good fence or a replacement fence for this type of saw.Sorry but you have to keep using a tape or replace the saw. Maybe someone will reply with some magic.good luck Edited March 28, 2014 by Doug-EdgewaterWW Quote
..Kev Posted March 28, 2014 Report Posted March 28, 2014 There should be some adjustment for the fence. This is a small contractor's saw so, maybe not much adjustment. Welcome to the forums! Hope you find some great answers here. Quote
Byrdie Posted March 28, 2014 Report Posted March 28, 2014 Hi Jenny. Welcome to Woodtalk and congrats on your first post. I had to gargle the saw model you have and I regret to say your method of checking parallel is about as good as it's going to get with that saw and fence combo. Nothing to worry about and good results can be had - I did the same for a lot of years. Use your tape measure to measure from the blade to the fence at both ends of the blade. If your blade raises and lowers pretty evenly I always like to do it with the blade fully raised so that the points I'm measuring at are as far apart as possible and then lower the blade to whatever your working height is. Good luck and let us see some of what you build. Quote
EdgewaterWW Posted March 28, 2014 Report Posted March 28, 2014 Byrdie, reading many reviews about this TS it's a common problem with the fence not staying parallel. Yes it can be set parallel, but move the fence and the two ends of the fence will not lock in parallel again. Quote
Freddie Posted March 28, 2014 Report Posted March 28, 2014 You say when its sliding it is not parallel, is it just when moving it or is it happening when locked? I use many different job site style saws for work, and even the cheapest of them all ( my dad owns a $139 skil) I was able to adjust the fence for parallel to the blade when locked. I learned to compensate for the saws lack of smooth slide for the fence. When I unlock the fence to move it, I keep forward pressure on the square against the rail as I move the fence, helps keep things smooth. I also maintain the pressure forward to let the rear of the fence properly engage the rear of the table to lock. 1 Quote
knotscott Posted March 28, 2014 Report Posted March 28, 2014 Welcome to the forum! Sorry for the bad news but, any table saw with the description "Contractor Table Saw" really is not good for woodworking... For the sake of clarity, what she has is a portable jobsite saw. A contractor saw is a full size stationary saw usually with a cast iron top....they originally had a belt drive induction motor handing off the back, but most of the motors have been moved inside the cabinet in more recent designs. It's not uncommon for folks to confuse the names, because most contractors now use a portable jobsite saws. With that said, there are limited upgrades available for most jobsite saws. It's possible to build it into a table saw station to help with working area and mass. You can add a fence upgrade to the station, but it can turn into a fair amount of work and money. If you can't get the fence on your Makita adjusted, IMHO it'd be better to sell the Makita, and pick up a good used full size contractor saw. The ABCs of Table Saws contractor saws: jobsite saw: Quote
tim0625 Posted March 28, 2014 Report Posted March 28, 2014 And...you can pick up a contractor's saw with a cast iron table on CL for a little money. Welcome to the forum! Quote
EdgewaterWW Posted March 28, 2014 Report Posted March 28, 2014 knotscott, your right. I used the term that one of the Makita re-sellers used and didn't think about it.I have two jobsite TS, a contractor TS and a old Cabinet TS, i guess I need to go get a Hybrid TS. Quote
Tpt life Posted March 28, 2014 Report Posted March 28, 2014 I don't know where to source this item. Ours was older than the hills themselves. We had a drop in frame like the black frame in Knotscotts last pic. We never used the Makita portable fence due to the very problem you reference. That fence system has seen almost no update in 20+ years. Quote
knotscott Posted March 28, 2014 Report Posted March 28, 2014 knotscott, your right. I used the term that one of the Makita re-sellers used and didn't think about it. I have two jobsite TS, a contractor TS and a old Cabinet TS, i guess I need to go get a Hybrid TS. That'd complete your set! Quote
krtwood Posted March 28, 2014 Report Posted March 28, 2014 With this kind of fence it helps to always make your last move of the fence towards the blade, ie start from a longer measurement than you want and work your way in. If you overshoot, go back and try again. Any fence that locks at both the front and back of the saw can end up locking slightly out of alignment. If you move it in this direction if anything it will lock with the back of the fence further out which is much safer than having it lock with it further in. Also you'll end up with a measurement that is longer than you expected instead of shorter which you can always fix with another pass. But really, nothing will improve your enjoyment more than moving from a jobsite saw to at least a contractor style. My contractor saw still has the locking at the front and back style fence though, so I use that same approach. Quote
Beechwood Chip Posted March 30, 2014 Report Posted March 30, 2014 My previous saw was a Bosch 4100 bench-top, portable, job-site saw. I never had any problem with the fence, and I never read about any problems. I got it for $380 refurbished from CPO. I think it lists around $600 new, at which point you should just get a contractor saw unless you need the portability. But for $380 I was very happy with it. Keep the fence track and mechanism free of sawdust, and make sure that the front on the fence is firmly seated against the guide rail before locking it down. That might help. Good luck, and welcome to the forum. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.