Recommended Posts

Posted

I'm planning a workbench that is made from construction grade 2x4s for the frame and possibly also for the top (depends how many I mess up on the frame).

The bench will be one of a pair that will take up over half of my available floor space and will have to cope with a serious amount of abuse. Having watched countless videos, read endless blogs, spent untold hours lying in bed at night cogitating I've now reached the point where I know what joints I'm going to use for the frame - mortise and tenon. Relatively simple but with a lot of strength and will allow me to dismantle it when I win the lottery and buy a big house with dedicated workshop - drool!!!

I'm thinking of a tusked tenon to join the front and rear rails to the legs, and a cogged tenon to join the side stretchers. This combination seems to give the maximum strength along the bench and allows me to tighten it up if it gets loose. Exactly the same joints will be used for the lower rails/stretchers.

 

post-15398-0-66987500-1399650245_thumb.jpost-15398-0-11489800-1399650244_thumb.j

 

What do you reckon - too complicated? Alternative solutions/advice gratefully accepted :unsure:

Posted

Seems like a far amount of work for a joint that's not all that stunning, if it's just a 2x4 bench I'd just do some shallow mortised and tenon joints and lag bolt that sucker together so I could have a bench to do some fancy joints on. 

Posted

All that joinery will be wasted on construction lumber. Most 2x4s are too soft to keep tight joints without glue or bolts. Lateral forces applied as you work at the bench will make the joints loose pretty fast.

Posted

Doesn't matter if you're making fine furniture or shop furniture.  The goal is to enjoy the process as much or more than the end result.  So I say the decision is solely yours.  

  • Like 1
Posted

That joint does look like fun to cut.  As far as "wasting" it on construction lumber, I think it would look better in the shop as part of a bench, than on a piece of furniture.  I say try cutting a joint, and see how tight it gets using the 2x4's and go from there.

Posted

Joints are only as strong as their weakest link, and that's the amount of wood left over after making the cuts. You don't have much meat in the leg or in the one stretcher. If I were building a bench from 2 x 4s I would assemble the legs as an "L". them simply tenon the rails into the legs and get on with making things.

 

Bob Lang

  • Like 1
Posted

Thanks for the input guys. Much appreciated and I've taken them on board.

Seems like a far amount of work for a joint that's not all that stunning, if it's just a 2x4 bench I'd just do some shallow mortised and tenon joints and lag bolt that sucker together so I could have a bench to do some fancy joints on. 

The aim wasn't to produce a stunning joint but rather one that would work. Think I got that a bit wrong as well :(

 

All that joinery will be wasted on construction lumber. Most 2x4s are too soft to keep tight joints without glue or bolts. Lateral forces applied as you work at the bench will make the joints loose pretty fast.

Very fair point there. It was one of my major concerns. I think this video (from about the 10 min point) from Paul Sellers shows how to solve the problem though.

 

Doesn't matter if you're making fine furniture or shop furniture.  The goal is to enjoy the process as much or more than the end result.  So I say the decision is solely yours.  

Couldn't agree more :)

 

That joint does look like fun to cut.  As far as "wasting" it on construction lumber, I think it would look better in the shop as part of a bench, than on a piece of furniture.  I say try cutting a joint, and see how tight it gets using the 2x4's and go from there.

I'm going to make a test joint to see how it performs. If nothing else it will give me some practice at making mortices and some firewood for next winter.

 

Joints are only as strong as their weakest link, and that's the amount of wood left over after making the cuts. You don't have much meat in the leg or in the one stretcher. If I were building a bench from 2 x 4s I would assemble the legs as an "L". them simply tenon the rails into the legs and get on with making things.

 

Bob Lang

Another very good point and I don't know why it didn't occur to me. I guess I just got carried away trying to get things all neatly lined up. I'm going to use the video above as the basis for creating the ends. It has 2 2x4s laminated to make a leg. That will double the amount of wood and as the rails will now be attached on the outside there will only be one joint through the legs at the top and one at the bottom therefore leaving a lot more wood and therefore (hopefully) a stronger joint.

 

Pocket screws and move on with your life :)

 

http://www.youtube.com/watch?v=69V07Uq9iDc

 

(How do you embed a youtube video on the forums?)

Don't have a pocket screw jig and to be honest I'm not a great fan of them, but it is a valid idea :)

 

As I said at the beginning guys, thanks for the input.You have saved me a great deal of wasted time and effort. Please have a post-15398-0-89383500-1399738720_thumb.pon me. I'm going to spend the next couple of days re-doing my design and then hopefully I'll have one that corrects all the glaring errors you pointed out.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   3 Members, 0 Anonymous, 58 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined