RichardA Posted June 14, 2014 Report Posted June 14, 2014 I think I made a decent deal today! But, I could use some information, if you have any to spare! I managed to get this plane, and it has just 2 markings anywhere on it! Under the cap iron it has 2 numbers 418 & 422! On the blade which may or may not be original to the plane it says Fulton tool Co. warranted! Can anyone tell me about this plane? I stripped it down and with a wire brush and some 150 sandpaper cleaned it up a bit. The blade needs serious regrinding and you wouldn't believe how high the rust stood on this thing. Is this going to be worth my time and effort to bring back to life? I haven't checked the flatness of the sole yet, I needed get in the A/C or add more rust to this monster. Man, it's hot today! And I still have to pick peas and mow the yard. An old man's work never ends! Well, I guess it will end someday! But not today! [i hope]....... Richard 1 Quote
G S Haydon Posted June 14, 2014 Report Posted June 14, 2014 Richard, when you say "got" was the seller using it as a boat anchor ? That's some deep, deep patina Never heard of the company but to look at it's a dead ringer for a Stanley/Bailey clone. I would guess anytime between 1900>1939. The wood seems to be rosewood, nice, what's left of it.... The sole is corrugated, the concept being it reduces friction, making the plane easier to work especially on resionous woods. I'm unsure as to what real difference this makes. If friction is that much of an issue use a wooden plane . I would hazard a guess that's it not worth much. It would be a labour of love to breathe new life into it. I wish you well with your journey Quote
Trip Posted June 14, 2014 Report Posted June 14, 2014 ==>some deep, deep patina Wow, there's even a politically correct term for rust... Who knew??? Let's see..... We could also go with Iron Challenged? How about Oxygen Enriched -- yea, I like that one... 1 Quote
G S Haydon Posted June 14, 2014 Report Posted June 14, 2014 I might start adding "Oxygen Enriched" to my ebay listings :-) 1 Quote
pghmyn Posted June 14, 2014 Report Posted June 14, 2014 Lost cause, I'd say no. Extensive journey, yes. I wouldn't expect it to be up and kicking next week, but a little here and there will give you a nice tool. I speak from no experience, however. Just what I feel would be the case. Good luck to you! Quote
RichardA Posted June 14, 2014 Author Report Posted June 14, 2014 Okay guys, I spent about 3 hours on this thing today. Rosewood is the correct answer, and it cleaned up a little bit, more to come! As for "got", the seller was in a good mood, and I paid 1 very empty goose egg for it. Boat anchor? I kinda thought so too, man was that thing cruddy, and some of the Oxygen Enrichment had more Oxygen enrichment on top of it! And I mean a lot.... Wire brushes, 150 paper. Some Paul Sellers grinding on the blade, The sole is damn near 0 flat the whole length, that was a surprise. Used some light machine oil and carburator cleaner, and everything seems to work the way it should. Put a rough edge on the blade, hooked it all back up, eyeballed the setting, threw a chunk of rough Cherry on the table, locked it down, and took a run at it........ Lovely curls, a little thick....adjust and a beautiful thin curl that made me smile. Next is , break it down again and really attack the cleaning, and spend some time getting a real edge on the blade. I'll take a couple of pics after all this sweat dries, and you can see the improvement, and there will be more, I assure you. I like this "Boat Anchor" so far... But I really don't like all that grease and Oxygen Enrichment, but I'll get it right! I just wish I knew it's name, and where it's from. Nameless boat anchors confuse me! Quote
G S Haydon Posted June 14, 2014 Report Posted June 14, 2014 Great work Richard! There be gold beneath that crud . Quote
RichardA Posted June 14, 2014 Author Report Posted June 14, 2014 Well, I wouldn't exactly call it gold, but it's sure less cruddy! After a few hours of research, [it was to hot to get in 112 degree shop today], I found that the plane is a Fulton model 7c Made by union, for fulton. Gonna get on it this evening when the temp drops to a decent 90. Quote
RichardA Posted June 14, 2014 Author Report Posted June 14, 2014 By the way Sam, how's the house? Haven't heard how your doing there... Got your shop figured out yet? Quote
pghmyn Posted June 15, 2014 Report Posted June 15, 2014 We were supposed to close on Friday, but I got a call 30 minutes before the meeting saying it was cancelled. The government grant hasn't been approved yet because the bank in Chicago is behind. I'm glad they waited until last minute to tell me this. I don't understand how they set up the closing, got that far in the process, without having the approval. I have a lot riding on that $8,000 grant. Also, enough about me, that plane looks great already! It will be polished up and looking brand new in no time! Quote
Alan Bienlein Posted June 15, 2014 Report Posted June 15, 2014 Clean it up with electrolysis and you go from this To this with just a green scotch brite pad and some olive oil. Quote
Tony Wilkins Posted June 15, 2014 Report Posted June 15, 2014 Great find Richard, sure it will serve you very well. Quote
RichardA Posted June 15, 2014 Author Report Posted June 15, 2014 Thanks Slack, I hope so! Alan, I've never tried electrolysis, I've heard it does a good job on removing unwanted hair, but as bad as that plane is, it's not very hairy! And that's quite a clean up on yours, and yours looked almost as bad as mine. Did you repaint yours? Hang in there Sam, it'll happen. Quote
Alan Bienlein Posted June 15, 2014 Report Posted June 15, 2014 I did repaint mine with some satin black enamel I had on hand. There was very little japaning left as you can see in the before photo so after the electrolysis I just cleaned it off and started fresh. This plane only cost me $20. Here is a video on electrolysis. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.