Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

My First Projects...

Featured Replies

Figured I should start a journal rather than continuing to post in my "Proposed Shop Layout" thread.

 

I plan to inaugurate the opening of my new shop with two projects.  They will be Christmas gifts for family members.  The first is a wooden beer tote that was suggested by Tom and of course the second project will be cutting boards.  There are numerous plans/pictures for beer totes on the web... I will come up with some hybridized combination of these examples.

 

I will begin with the beer totes as I don't have my jointer yet and the lumber I have for the cutting boards is rough.  For the totes our local Home Depot had some s4s maple that I will use in combination with a few other species.

 

One of the first lessons I learned is that I can't drill a perpendicular 1" hole with a power drill free hand.  Hmmm could be why a drill press is so handy :)

 

WLNXdRHl.jpg

 

They looked great until I stuck the dowels in the holes... Hard to see in the pic but the boards are not parallel in the least.

 

Af4YJxol.jpg

 

 

In any case believe or not I did not run out and buy a drill press... I am sure many of you would have expected me to do that. (Eric) :)  I went the less expensive route and just picked up a drill guide.  I'll get a drill press next year.  Although Jet's are on sale right now 15% off...hmmm...hmmm...don't do it Dave... OK crisis averted we can move on. 

 

One other piece of advice that members on this forum gave me and have given others is to buy tools when the project dictates it!  If I had heeded that advice I would have a purchased the drill press today and likely not gotten a Domino so soon.  But the "Green" just had me under its spell.

 

So it was back to the Home Depot for some more maple and will begin anew this evening.  My daughter said she'd help...might be good idea to have 2 sets of eyes looking at this... stay tuned.

  • Replies 99
  • Views 15.7k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • The only measurements you need are the for the first board you cut.  Everything else is relative.

  • Even after 40 years I still occasionally find missed glue squeeze out in the first stage of finishing. Sandpaper gums up incredibly fast so I use a sharp card scraper. Card scrapers take some practice

  • That advice can be put in a variety of ways, but the way you just laid it out is the most boiled down.  I'm not sure anyone ever said, "Go out and buy every tool you can fathom you'll ever want for ev

Posted Images

It's a good job Festool don't make drill presses. They really are worthwhile Dave and you can pick them up reasonably cheap. A drill press really does keep them holes square.

Great to see the shop in operation.

All part of the learning process..  I would suggest a full stand up press rather than a bench top version..

 

Nice to see some sawdust in the new shop.. 

Good first project and great to see some sawdust being made! :)

Awesome Dave, I look forward to seeing how they come out. Are you using a template or any pattern to do any curves or anything? As for the drill press, floor standing would be the way to go. I almost never use my drill press, and now that I need it. I don't have it, it's in my parents basement. I have no space to put it in the shop right now. Time to move things out, giving my dad my media blast cabinet and I'll put the drill press there. Problem solved. 2 weeks off during Christmas break to get my shop as complete as I can. 

I would suggest a full stand up press rather than a bench top version..

As for the drill press, floor standing would be the way to go.

 

Why?   I often see that advice but have never understood the reasoning.

I was thinking the same thing.  I have a full-standing model but I am considering replacing it with a bench-top model.  The odds of me needing to drill a piece that won't fit in a benchtop seems unlikely.  Regaining the floor space seems like a nice route.

A learning experience.  Could have been worse...you could have turned the board into a helicopter blade on the powerdrill.

 

Just at a glance, ganging up your boards during the drilling process might solve some of the accuracy problems. 

Last year I helped my dad rebuild a car engine and we used my drill press to drill a hole in the back of the heads and then tapped the hole for a bolt to mount a bracket to. His bench top drill press wouldn't fit it. Also, you generally get a bigger table, deeper throat, and you could bore through longer stock for making lamps, and such (if you don't have a lathe) Bigger lathes also have bigger motors and more power. 

TIODS, on 15 Dec 2014 - 3:52 PM, said:snapback.png

I would suggest a full stand up press rather than a bench top version..

 

Why?   I often see that advice but have never understood the reasoning.

Imagine drilling a 3/8" hole two inches into the endgrain of a 4 foot board.

Why?   I often see that advice but have never understood the reasoning.

 

It never fails that as soon as you don't have that capacity, you need it.  I would much rather have my drill press usable for large stock where the holes are critical.

The chuck on my benchtop drill press is too small for the larger forstner bits, say 2.5" and up.

Also, on larger shank bits it's tough to get it tight enough to keep the bit from spinning in the chuck.

Dave

 

 

One other piece of advice that members on this forum gave me and have given others is to buy tools when the project dictates it!  If I had heeded that advice I would have a purchased the drill press today

 

That advice can be put in a variety of ways, but the way you just laid it out is the most boiled down.  I'm not sure anyone ever said, "Go out and buy every tool you can fathom you'll ever want for every project you ever plan to build."

 

The wisdom of that advice is when it's used in a more nuanced way, such as, "When there's a task you need to complete, and there's no other way to do it without a particular tool, then go buy that tool."

 

I'm in no position to give you flack for buying tools...I'm an addict, too.  But most of us have been slowly building our collections for years or decades, and finding work-arounds for countless challenges through countless projects.  I'd actually argue that it makes you a better woodworker to be deprived of certain tools in the beginning, because you're forced to think outside the box and try different techniques.

 

Good to see you mangling some wood, Dave.  Slow down and take a breath.  It's going to be frustrating in the beginning.  It always is. :)

Slow down and take a breath. It's going to be frustrating in the beginning. It always is. :)

Yea you never know if you're doing it right...too fast too slow...too hard too soft...is this working at all? Well it seems kinda nice...I'll just keep going...oh I think I'm getting a hang--uh oh...all done. Time to clean up.

Yea you never know if you're doing it right...too fast too slow...too hard too soft...is this working at all? Well it seems kinda nice...I'll just keep going...oh I think I'm getting a hang--uh oh...all done. Time to clean up.

 

lol, that sounds more like a teenager's first go at it than it does woodworking :)

lol, that sounds more like a teenager's first go at it than it does woodworking :)

That was the joke Bill. =p

lol, that sounds more like a teenager's first go at it than it does woodworking :)

You made bourbon come out of my nose. Hurts so good.

 

 

So it was back to the Home Depot for some more maple and will begin anew this evening.  My daughter said she'd help...might be good idea to have 2 sets of eyes looking at this... stay tuned.

  • Author

 

 

So it was back to the Home Depot for some more maple and will begin anew this evening.  My daughter said she'd help...might be good idea to have 2 sets of eyes looking at this... stay tuned.

Maple at HD?

Ours has syp, poplar and red oak. Curious as to what others have throughout the US? But, I guess that's guts for another thread

  • Author

So I think the drill attachment helped but it was no panacea... It felt like there was a lot of slop.  I did drill a pair of boards at a time which helped a bit.  I may end up down at WoodCraft asking to use their drill press.

 

56Hw6Fvl.jpg

 

Also made the first real cut on the table saw...

 

fltFObcl.jpg

  • Author

Unintended purpose of the pic but accurate nonetheless. I realized after posting it someone would infer ... "Hey he still has all his fingers!"

I thought it was the obligatory "for the low low price of 30 grand, you too could cut this board!"

  • Author

Hell by the time I'm done I won't even see 30 grand in the rear-view mirror and probably not my wife either...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.