Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Vacuum Pump

Featured Replies

Lately I've been doing a lot of research about using vacuum pumps and bags for veneering.  I've read a lot and watched quite a few videos.  I'm pretty confident I can make a vacuum bag using some heavy gauge vinyl and a few miscellaneous fittings/connectors, etc. 

My current need is to attach ⅛" shop made veneer panels to both sides of a 1" thick BB plywood approx 30" x 44".

I'm still confused about the vacuum pump itself - what type/size, etc. should I get?  How much vacuum should it draw?  How many cfm? Continuous duty? I only have a small pancake compressor (for brad nailing only) so I'm not sure if the Venturi style is an option for me.

I found what seem to be task specific pumps but they seem quite expensive - $350 -$800 USD just for a pump I will use very occasionally.

Anyone have experience using vac pumps used by HVAC techs (I can get used on eBay for less than $50) or what about the hand pump types used by automotive guys (http://www.princessauto.com/en/detail/powerfist-vacuum-pump-and-brake-bleeder-kit/A-p8050832e) which I can get new for between $35-$70.

As always, I appreciate your comments.

No experience at all with a vacuum press, but I don't think a hand pump would work because there is always going to be some leakage, so you'd have to sit there all the while the glue is drying. My theory anyway.

Oh, and I don't think I'd buy a Powerfist anything. I've heard nothing good about their tools.

I'll be paying attention to what others say cause I'm interested in getting set up with a vacuum press.

Edited by drzaius

I have HVAC vacuum pumps in my shop. They are typically 6 to 8 cfm,  but I don't know all the answers to your question. 

I did find this which is section E3 and can be found with a wealth of other related information regarding veneering at http://www.joewoodworker.com/veneering/faq.htm .

Vacuum Flow: If your pump has a flow rating of more than 4 CFM, you will need to add a vacuum damper to prevent the vacuum controller from turning on and off rapidly. This chattering will quickly damage the pump. Keep in mind that your vacuum pump's CFM rating effects the maximum bag and project size. Learn more by clicking here.

And here's a link to the item in reference

 http://www.veneersupplies.com/products/Vacuum-Damper-For-Large-Vacuum-Pumps.html

Let me know when you have this all ironed out, because If it works I will borrow a Vacuum pump from work, and have my wife return it, when I am dead.

There's a bit more to it than 'just a pump'...

4-10cfm (6cfm optimal hobby setup), 25Hg, Continuous duty w/ auto shutoff

Here's Joe's DIY site:

http://www.joewoodworker.com/veneering/welcome.htm

http://www.joewoodworker.com/docs/ProjectEVS.pdf

 

Last time I looked, his kit's around $250-$300...

 

 

Edited by hhh

Can you add an auto-shutoff to an HVAC pump Trip?

It could be done, if nothing else a solid state relay controling the pump hooked up to a low pressure switch.

My pump is an od continuous duty cast iron vane pump. Kinda messy needs an oil jar to sip from. Most modern pumps are diaphragm I think .

Joe Woodworkers site has lots of info and great prices on all the hard to find bits you will need. I use my vac pump for clamping more than pressing. With a foot pedal I can clamp a part in seconds, route the laminated face, file the edge and remove the part taking 1 1/2 minutes . It is so easy to sand something that is held from underneath and you have access to all 4 edges and the face.

here's the place @thewoodwhisperer referenced for veneering supplies in the gaming table build:  http://veneersupplies.com/

 

I see two models of vacuum pump on their site - a 1.1 CFM continuous duty (for up to 4' x 4') and a 5.5 CFM continuous duty (for up to 4' x 15').  Maybe you can check the other pump specs against the HVAC pumps that are available.

 

As everything is a time /  money tradeoff, I bought a ready to go 6CFM pump from Vacupress.

Many of my accessories and supplies come from Joe, but I didn't build my own example of many of my tools.

No matter how you get there, I can tell you that having a vacuum source in the shop is addictive.  Once you find the biggest one you think you'll need, go one up...   :lol:   I'm using a lot more veneer than I thought I would, because I can and it makes great looking stuff!

If you are looking at used pumps, Robinaire are pretty good.  Give the oil a whiff (seriously) to make sure it has not been sitting there with oil from a burned out compressor.  You will know if it has.  Pulling a burned-out system down is ok; leaving that oil in the pump is not.  No matter what, change the oil on the pump (a few dollars) before you start.

I've left refrigeration vacuum pumps on overnight, they are meant to hold a vacuum for long periods of time.  

Edited by Lee Bussy

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.