andrew-in-austin Posted December 10, 2015 Report Posted December 10, 2015 Really good video:My only complaint is the Kapex was not tested, even though it's in the same workshop!I was surprised how bad the bosch glide was. Quote
boelkers Posted December 10, 2015 Report Posted December 10, 2015 Thank you for sharing that. I was really surprised to see those results. I wonder is Marc has had a similar experience with his new Bosch saw. Quote
ChrisDraper Posted December 10, 2015 Report Posted December 10, 2015 I will note that after showing how efficient the Dewalt saw is with that new Freud blade that he then cuts to the Bosch throwing dust everywhere. However, the Bosch saw clearly doesn't have the same new Freud 80 tooth blade. Quote
drzaius Posted December 10, 2015 Report Posted December 10, 2015 I built a box behind my saw with an 8" duct to it. No more dust. Quote
JosephThomas Posted December 10, 2015 Report Posted December 10, 2015 I'm sure I've read it somewhere before, but can someone explain why people mostly use shop vacs/extractors with the miter saw instead of their DCs? (Or link to a good article about it). Thanks in advance. Quote
ottacat Posted December 10, 2015 Report Posted December 10, 2015 (edited) Both the DeWalt and Ridgid had 1 oz of dust that wasn't collected out of 3 lbs (48 oz), this represents a nearly 98% collection efficiency rate. The Kapex claims 90 - 91%.So... either the test methodology is flawed (no bevel cuts, no angle cuts, no thick pieces of wood) or the Kapex's dust collection is inferior. I guess they didn't want to irritate an advertiser. I can't think of any other reasonable excuse to exclude the Kapex given the author had one and it would have been a useful reference. Edited December 10, 2015 by ottacat Quote
Tom King Posted December 10, 2015 Report Posted December 10, 2015 That's not dust collection. That's wishful thinking. Mine must be similar to dzaious, but I only use a 6" duct. It gets all of it inside finished houses, and it's a 12" saw. Quote
Al Capwn Posted December 10, 2015 Report Posted December 10, 2015 I'm sure I've read it somewhere before, but can someone explain why people mostly use shop vacs/extractors with the miter saw instead of their DCs? (Or link to a good article about it). Thanks in advance.*Note: The following information is based upon staying in a Holiday Inn Express one time and has no practical experience.One reason may be that the port on most miter saws are the 2 1/2" size that shop vacs can attach directly to. Given that miter saws are frequently used for rough-in work, a shop vac is a bit more portable than a true DC setup would.In terms of the difference, ShopVacs have a high static pressure and low CFM. This means they have very powerful suction, but only at a very close range. This is why your ShopVac will suck up nuts and bolts with gusto, but requires close proximity. It won't suck material in a wider space.DCs have a much higher CFM and lower static pressure. That is because DCs are designed to pull in a large volume of air within a wider space, albeit at lower pressure.If the CFM theory holds true, a DC should be better than a ShopVac since a miter saw is notorious for ejecting dust in a wide area - but I can't speak from any level of experience. General advice I have read is that it is best to try and collect dust as close to the source as possible, rather than trying to pull it from the air. Quote
Beechwood Chip Posted December 10, 2015 Report Posted December 10, 2015 This test only measured large particles that settled on surfaces and could be seen. The fine particles that get deep into your lungs and can't be coughed up will be floating in the air, invisible, and won't be measured by this test. You can't really compare the %ages unless you know what they were measuring and how they measured it. Quote
rodger. Posted December 10, 2015 Report Posted December 10, 2015 As a non-scientific test, I have the Kapex and I can tell you first hand that the DC is incredible. Quote
andrew-in-austin Posted December 10, 2015 Author Report Posted December 10, 2015 I can't deny how great the Dewalt and Rigid were, however. I doubt we'll ever see a scientific comparison involving the Kapex. Even the Kapex will spew dust if you are not careful about how the cut the wood.I agree about just not using a miter saw to eliminate the problem I plan on using a radial arm saw with a 6" dust collection port, which I am currently measuring ~1200 CFM. If that does not do the trick, I don't know what will. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.