Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Sanding Shellac

Featured Replies

I like to play around every now and then.  This time around I'm playing with finishes on some test boxes that I made.  Specifically, brush applied finishes instead of my usual wipe-on or sprayed.     I'm having a bit of a problem with Shellac.   I've got the build-up that I want, but when I started my final sanding at 400grit, I was left with a white residue that doesn't seem to want to come off.  How do I get rid of the residue?

 

Adam

Have you tried wiping the project with a damp (not wet) rag-damp with alcohol, not water.?

==>sanding at 400grit, I was left with a white residue that doesn't seem to want to come off.

white residue is good -- usually means shellac is cured...

residue doesn't come off -- usually means shellac is not cured... or... heat...

how did you sand? portable sander? could be heat... what did the residue on the paper look like? photos?

  • Author

no, I have not tried wiping with alcohol. I'll give it a try.

i hand sanded about 5times back&forth. It's a small drawer front, maybe 5" x 2".  Residue on paper is also white.

adam

==>I have not tried wiping with alcohol. I'll give it a try.

Well, i'm not totally sure about that one... You'll remove the residue, but may streak the finish if everything isn't really cured... Have you tried a microfiber or tack cloth? how long between coats? if previous coat was not cured, that'd do it... i might leave it overnight and sand again...

I'd be tempted to go over it with a fine scotchbright pad (dry) to pull any residue out.   Give it a good shot of compressed air and apply your final coat :-)

Are you sanding to level the finish or want to rub out? Shellac dries hard and scratches easily so you'll want to start with higher grit for rubbing out. If you just want to level before final coat sounds like you have success with white dust. 

I'm far from an expert in shellac, but it seems like 400grit is way too coarse for a final sanding (unless I'm misunderstanding, it seems like you're sanding *after* your final coat, right?)  I think people usually rub out with steel wool or some other high grit pad to get the sheen they want / knock down dust nibs.  I think 400grit would just be for between coats.  If it were me I would put another light coat on and then rub out with 0000 or a 1000 grit pad.

==>unless I'm misunderstanding, it seems like you're sanding *after* your final coat, right?

Excellent clarification...

 

But we still need to understand 'residue'... I suspect it may just be extra-pesky dust, so no actual problem with the finish...

  • Author

I'm sanding to level out some high spots.  I got to the build up that I wanted, but there were a few high spots that I needed to knock down.  If 400 is too low to start with then that is part of the problem.    I'm going to do the alcohol rub (suggested above), let it dry,  apply one more coat to get back to where I want it to be, and then use the 0000 steel wool to get rid of dust nibs.

HHH- it is not dust.  definitely some sort of residue from the shellac.  I let it sit overnight before sanding, but its been in the 30's at night and no higher than 50's during the day so it may not have been cured enough.

Shellac doesn't cure - it should dry hard once the DNA evaporates. If it doesn't dry hard or corns the sandpaper then it might have gone bad. 

  • Author

I'm using Zinsser shellac that I bought a few weeks ago.  It looks good in the can so I don't think it's old.  Only date code check could say for sure.

Z's Seal Coat's AOK -- use it all the time... I typically cut it 50/50 for initial sealer and 70/30 for subsequent... I can't think of any experience with residue... I've never used Z's Bulls Eye (wax-shellac product)... So couldn't comment on that...

50/50 seal coat is where it's at.....made me a believer in shellac.

Sent from my iPhone using Tapatalk

50/50 is a great sealer -- and a barrier to shop contaminants...

When you start building period pieces -- that's when shellac comes into its own... Take the ubiquitous lowboy: fan carving, a finial or two -- shellac and a quality detail brush are all you need...

I usually avoid sanding if i can, i will sand my first few thicker coats and then do like 1/4 lbs cut for anywhere from 2 to 8 coats in rapid sequence, you get very little build when doing this but because its so thin it will go on and self flatten and the next coat will burn in and remove most of the last coats imperfections. I find almost no benefit in sanding these thin coats.

==>^^^

Have you tried traditional French polish? You're about 90% there... When first starting building for myself, I became overly-enamored of the technique. Many (most?) of my early pieces were FP... I don't seem to have the patience anymore... :)

For levelling I used 600 grt and a bit of the same oil I used in the french polish process as lube (olive oil in my case).  The last go over was with a pad, slightly damp with alcohol only (spiriting off).  You don't want any pause in the stroke, be moving, land the pad, and swoop off.  If there is any pause in the stroke while touching the piece it will leave a mark.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.