Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Dust collection setup

Featured Replies

I'm starting to get my shop kinda like I want it. I'm still trying to figure out setup. I was going to get nordfab to hook to my cyclone. My question is should I try to come up with an exact setup and use their design service or start ordering parts and just kinda wing it as I go. I've been using a small rockler unit to get by as I start building a few things but that is getting old real quick. Any advice or suggestions much appreciated.

Sent from my iPhone using Tapatalk

Easy answer-> Design service. Nordfab isn't cheap, do it once, do it right. Plan for future tools in the design and add some capped off future branches.

The ductwork is the heart of any DC system -- the cyclone just hooks to it... To get the ductwork right, you’ve got to know the requirements of the tools you intend to clear (both the tools you have now and the tools you intend to purchase in the future)...

If all your tools are (or will be) 4-inch inlet and the runs are short, then there isn’t much design involved and, with a bit of web-knowledge, you can probably wing it... But if you intend to procure 5-inch or 6-inch inlet tools, drum sanders, run lots of ductwork, etc then professional design is strongly advised...

What I did: listed all the tools I had at the time, the tools I intended to get based on the projects I wanted to build and a basic shop layout. Sent the lot to a design service... With that basic info and $200, I received a thick report including shop layout, ductwork design, elevation view of each tool and its DC hookup, parts list, and the minimum fan curve required to drive the ductwork... Here's the plan overview from the design package:

 

ductwork-plan-view.thumb.jpg.09f02b2a42a

 

As an aside -- the $200 was worth it...

1 hour ago, Janello said:

Easy answer-> Design service. Nordfab isn't cheap, do it once, do it right. Plan for future tools in the design and add some capped off future branches.

Yup no brainier if you're going to fork out money for Nordfab to use a design service. Otherwise it would be like ordering prime rib well done. 

 

For my current shop (above diagram), I used Oneida Air System's (Oneida) service. I was pleased with the service itself and the design has stood the test of time... I plan to use Oneida’s service on my next shop (planned for 2017). You can read the design service questionnaire here: http://www.oneida-air.com/pdf/shop_plan_design_form_2014.pdf

With the Oneida design, I can run any two tools simultaneously (as long as one of them isn’t the wide-belt) and leave any three blast gates open. This was a design requirement – I tend to run the jointer and table saw simultaneously, the jointer and bandsaw simultaneously or the planer and wide-belt simultaneously (although I’ve got to be somewhat careful with that workflow to capture the fines). With their design, I can drive the ductwork to collect sub-0.5u particles with HEPA filtration and a 3HP separator... Note: most of my tools are either 5-inch, 6-inch, dual 4-inch DC-inlet or dual 5-inch (i.e. some pretty big tools)... There are also 4 floor sweeps in the design.

The best place to start is to request a copy of Oneida’s Ductwork Design Toolkit. It’s a 40-page booklet on the basics of dust collection and ductwork design... Here are some sample pages: http://www.oneida-air.com/static.asp?htmltemplate=static/ductwork_tutorial01.html

Do you need a service? It depends... If you’ve got a small hobby shop (short runs) running small hobby-sized tools (4-inch inlet) one at a time, then you can get most of what you need from various websites (Pentz’s being the best known)... For these cases, a constant-diameter trunk (read as 6” PVC) run right to the tool can provide OK performance as long as you aren’t worried about collecting sub-0.5u dust (fines) or true HEPA performance... It’s when you introduce larger tools, stationary sanders, longer runs and want do more than just keep the shop clean (i.e. actually collect dangerous dust) that professional design comes into play...

I can also recommend Air Energy Systems and Air Systems... There are many other respected services, but I can’t recommend them due to lack of direct interaction...

  • Popular Post
12 hours ago, hhh said:

 

ductwork-plan-view.thumb.jpg.09f02b2a42a

 

 

Another step in the direction towards that shop tour trip's never going to give us ;-)

  • Author

Thanks for the input I've just been worried about flexibility being I'm not sure of exact setup but I see now I can just make a few flexible plans for future changes.

Sent from my iPhone using Tapatalk

This is why I've spent so much time before ordering my new system.  I want to be sure that my major equipment isn't going to move.  

I've had my shop in 3 different orientations now and I'm still not sure that's where I want things..  Seriously considering a 4th.

  • Author

Lol. Yea when I was building my shop I had floor outlets put in because I was 100 percent sure of my setup [emoji12]. Now I'm 100 percent unsure!!

Sent from my iPhone using Tapatalk

I've also used Oneida's design service when customers needed help designing a system. Good folks who know what they're doing. $200 is a lot less than the freight and restocking charges to return a system that doesn't work for you.

==>Now I'm 100 percent unsure

You don't have to be 100 percent sure... You need to know the size/requirements of the tools and a basic layout axis... The design service can get the main trunkline and branch connects... The drops will change over time -- there's no way to get a shop 100 percent set and never have it change -- what fun would that be? :)

If you know the tools you'll get and have a basic length of run, you can get started...

 

I considered using a design service, but I only ever run 1 machine at a time. So I just went with 8" spiral duct everywhere & reduce down to 6" or 4" at each machine. My theory being that big duct all the way to the outlet will offer less pressure loss than reducing size along the way. Seems to have worked out very well. I have an Oneida V-5000.

I understand though, that if more than 1 machine is being used a much more detailed design would be required to ensure balanced flow.

==>just went with 8" spiral duct everywhere & reduce down to 6" or 4" at each machine

Obviously, a design service is ideal... But if you've got an 8" inlet cyclone, then an 8" trunkline is the way to go... It's what a design service would start you with anyway... The other benefit -- starting with an 8" backbone, you are future-proofing your install... If you ever get a 5" or 6" inlet tool, then the central trunkline is still AOK... With a solid backbone, you can always change things downstream later...

Low air velocity doesn't seem to be a problem either with the 8" duct, which I though might be an issue. It will easily suck an 1 1/2" cube of spruce up an 8' vertical run. 

==>Low air velocity doesn't seem to be a problem either with the 8" duct, which I though might be an issue

One tool at a time, 5HP cyclone, fairly short runs with blast gate discipline should be OK for an 8" trunkline... Obviously, as the runs get longer, you decrease diameter to maintain velocity... If you look at my system diagram above, you'll notice the diameter decreasing as distance increases. It's not about HP; it's about maintaining sufficient velocity to capture and transport fines (if that's your goal -- for many, the goal is just keeping the shop clean). I've got a 6" inlet tool (jointer) at the end of the trunkline, but the diameter changes along the trunk keep the velocity above 3800 FPM (a design goal)...

One thing, I believe the old-style V-5K was an with 8" inlet and they switched to 7" inlet with the redesign. As a general rule, you want to match your initial trunkline up to the first branch to the inlet diameter... future planning...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.