minorhero Posted March 14, 2016 Report Posted March 14, 2016 Beta folks, Looking to buy a dedicated full kerf crosscut blade for my table saw. I have a ww2 combo and a ww2 24tooth rip blade. Looking online a lot of companies either don't offer a dedicated crosscut for table saw or only sell thin kerf models. Forrest has the duraline sp? line but it costs almost 200$. I was looking for something cheaper if it exists but wanted comparable quality. Anyone have any suggestions? Quote
AceHoleInOne Posted March 14, 2016 Report Posted March 14, 2016 Ummm, any 40T combo blade....will that float your boat? Sawstop has the 40T combo. I like the 40T Freud Diablo, find it at Home Cheapo for about $30.00 -Ace- Quote
Brendon_t Posted March 14, 2016 Report Posted March 14, 2016 I my best results in full fearful world come from a 50t marbles blade. Although not a crosscut only, it gives great finish and has never chipped out the corner of a mitre cut. Quote
Chet Posted March 14, 2016 Report Posted March 14, 2016 On my table saw I have been using the Freud 80 tooth ATB ultimate cutoff which is a full kerf blade that I have been real happy with. On my miter saw I have had a (12inch) 80 tooth Freud Diablo that also cam from the same fine emporium that Ace got his. The cheaper Diablo does seem to dull quicker then the other Freuds that I own. Quote
Chestnut Posted March 14, 2016 Report Posted March 14, 2016 I have 2 freud 80 tooth Ultimate Cutoff blades one full kerf one thin kerf. I really like their cut quality though i use them in my sliding miter. In my table saw i have a Freud Combination and it makes pretty clean crosscuts but not nearly as nice as the ultimate cutoff. I don't notice a cut quality difference between full kerf and think kerf. Quote
Guest Posted March 14, 2016 Report Posted March 14, 2016 I typically use a 40t woodworker for cross cuts. If I need an especially clean cross cut on my table saw I use one of these from carbide processors. It is designed for sheet goods but does a nice job on solid wood cross cuts. http://www.carbideprocessors.com/melamine-saw-blade-10in-x-80t-hatb-popular-tools-lm1080/ I own a bunch of their blades and they seem very close to forrest in quality and in many cases the cost is much less. I am sure they have a blade that is a similar configuration as the duraline you are looking at. Quote
minorhero Posted March 14, 2016 Author Report Posted March 14, 2016 Thank you for the heads up about carbide processors. I had not heard of them before. Unfortunately their crosscut blade costs 157$ which is not much of a savings off of the Forrest blade. I am trying to avoid blades used for miter saws or radial arm saws. That means no negative hook blades which eliminates quite a few options. I have found a cmt blade which fits the bill but no reviews on it and frankly the reviews I do find on cmt suggest they make good budget blades but don't compare to the likes of forrest, infinity, or ridge carbide. Quote
AceHoleInOne Posted March 14, 2016 Report Posted March 14, 2016 Just try the Freud Diablo. Its 30.00 bucks. As they say, rejection requires knowledge. Its a good cheap blade. If ya don't like it. Try the hot dog trick with your new Sawstop......... -Ace- Quote
Chestnut Posted March 14, 2016 Report Posted March 14, 2016 22 minutes ago, minorhero said: Thank you for the heads up about carbide processors. I had not heard of them before. Unfortunately their crosscut blade costs 157$ which is not much of a savings off of the Forrest blade. I am trying to avoid blades used for miter saws or radial arm saws. That means no negative hook blades which eliminates quite a few options. I have found a cmt blade which fits the bill but no reviews on it and frankly the reviews I do find on cmt suggest they make good budget blades but don't compare to the likes of forrest, infinity, or ridge carbide. The ultimate cutoff blades that ace and a few others mentioned are positive hook angle blades. Having used negative hook angle blades i agree with you an avoiding them. Mine has a 10 degree positive hook. Quote
Guest Posted March 14, 2016 Report Posted March 14, 2016 Have you tried your ww2 for cross cuts? In my experience it works great. I am surprised you need something "better". If you are have problems with the ww2 then maybe it needs to be sharpened. Quote
minorhero Posted March 14, 2016 Author Report Posted March 14, 2016 I looked at the ultimate cut off blade but unfortunately it is a thin kerf according to the description at .116" The ww2 combo is ok, but having used dedicated crosscut blades before I definitely notice a difference in cut quality. We are not talking a huge difference but I recently upgraded my saw and now I want to raise my personal level a bit. Quote
PeteJr Posted March 14, 2016 Report Posted March 14, 2016 I use the WWII with a zero clearance for all crosscuts and it's wonderful. I have two and I keep them razor sharp. Quote
Chet Posted March 14, 2016 Report Posted March 14, 2016 My ultimate cutoff is a is 1/8 it is probably .116. you are most likely loosing some thing in the metric conversion, I believe they are made in Italy or something like that. I think the thin kerf are labeled 3/32 or .091 or .093 something like that. This is the one I have- http://www.amazon.com/Freud-LU85R010-10-Inch-Ultimate-PermaShield/dp/B0000223KU/ref=sr_1_1/179-1815819-3936160?ie=UTF8&qid=1457988184&sr=8-1&keywords=freud+ultimate+cutoff This is the same blade but thin kerf http://www.amazon.com/Freud-LU74R010-10-Inch-80-Tooth-PermaShield/dp/B0002H49ZS/ref=sr_1_2/179-1815819-3936160?ie=UTF8&qid=1457988184&sr=8-2&keywords=freud+ultimate+cutoff Quote
knotscott Posted March 14, 2016 Report Posted March 14, 2016 IME, CMT Industrial blades are pretty comparable to Freud's Industrial line. Their ITK and ITK Plus lines aren't quite to that level. What are you trying to accomplish by avoiding anything with a negative hook? For cleanest cut, I'd be looking at the Infinity 010-080, Freud LU80, Forrest Duraline, CMT 210.080.10. For a really clean cut and a little better edge life, the Freud LU85 is a solid choice too. Quote
minorhero Posted March 14, 2016 Author Report Posted March 14, 2016 43 minutes ago, Chet K. said: My ultimate cutoff is a is 1/8 it is probably .116. you are most likely loosing some thing in the metric conversion, I believe they are made in Italy or something like that. I think the thin kerf are labeled 3/32 or .091 or .093 something like that. This is the one I have- http://www.amazon.com/Freud-LU85R010-10-Inch-Ultimate-PermaShield/dp/B0000223KU/ref=sr_1_1/179-1815819-3936160?ie=UTF8&qid=1457988184&sr=8-1&keywords=freud+ultimate+cutoff This is the same blade but thin kerf http://www.amazon.com/Freud-LU74R010-10-Inch-80-Tooth-PermaShield/dp/B0002H49ZS/ref=sr_1_2/179-1815819-3936160?ie=UTF8&qid=1457988184&sr=8-2&keywords=freud+ultimate+cutoff I don't think its a metric thing. .125 is the same as 1/8. Anything smaller then that and its thin kerf. The top link you have in the description says .116. The thin kerf blade is even thinner. Either the description is wrong or the blade is not a full 1/8 kerf. Basically I have 2 things against thin kerfs. One the scale on my saw is set to the full kerf thickness. So if I switch blades I need to either, reset my scale, not use my scale, or have cuts that are off by whatever the blade thickness difference is. I prefer to avoid that whole issue and just use blades all the same thickness The second issue I have is stability. Thicker kerf blades cut cleaner but require more power out of a motor. My new saw has a 3hp motor so I am not worried about the increase in power needed. Quote
pkinneb Posted March 14, 2016 Report Posted March 14, 2016 47 minutes ago, Chet K. said: My ultimate cutoff is a is 1/8 it is probably .116. you are most likely loosing some thing in the metric conversion, I believe they are made in Italy or something like that. I think the thin kerf are labeled 3/32 or .091 or .093 something like that. This is the one I have- http://www.amazon.com/Freud-LU85R010-10-Inch-Ultimate-PermaShield/dp/B0000223KU/ref=sr_1_1/179-1815819-3936160?ie=UTF8&qid=1457988184&sr=8-1&keywords=freud+ultimate+cutoff This is the same blade but thin kerf http://www.amazon.com/Freud-LU74R010-10-Inch-80-Tooth-PermaShield/dp/B0002H49ZS/ref=sr_1_2/179-1815819-3936160?ie=UTF8&qid=1457988184&sr=8-2&keywords=freud+ultimate+cutoff These are the blades I use. I have both but use TK for almost everything now. I also use their glue line rip blades and find them to be very good quality for the price. I also have a couple of WWII blades but I use those primarily for plywood these days. Quote
Dave's Not Here Posted March 14, 2016 Report Posted March 14, 2016 Nothing new here to offer except another +1 for the Freud LU85R010. Quote
minorhero Posted March 14, 2016 Author Report Posted March 14, 2016 36 minutes ago, knotscott said: IME, CMT Industrial blades are pretty comparable to Freud's Industrial line. Their ITK and ITK Plus lines aren't quite to that level. What are you trying to accomplish by avoiding anything with a negative hook? For cleanest cut, I'd be looking at the Infinity 010-080, Freud LU80, Forrest Duraline, CMT 210.080.10. For a really clean cut and a little better edge life, the Freud LU85 is a solid choice too. Thank you! I was considering the at the Infinity 010-080 and the Freud LU80. The CMT 210.080.10 is the CMT blade I found and mentioned earlier. Both the infinity and freud call themselves plywood or laminate blades, while the CMT calls itself a fine cutoff blade. The Infinity and the CMT are very similar/the same blade design in that they have a 5 degree hook and a 40 degree (some cmt descriptions say 38 degree) bevel on the atb grind. The Freud on the other hand has a 2 degree hook. Any thoughts on which of the three might be the best? As to why I am avoiding a negative hook. I have read online (not sure how true it is) that a negative hook while a good thing for a miter or radial arm saw is actually dangerous on a table saw more likely to result in kickback. I don't know about that but I have experienced a difference with using the wrong blade on my old unisaw which was 1 hp. The negative hook definitely was more difficult to push material through then positive hook blades. Quote
knotscott Posted March 14, 2016 Report Posted March 14, 2016 I've been more impressed with Infinity blades than any other brand I've tried. I'd definitely opt for the Infinity 010-080 Ultrasmooth since it's been on your radar. Quote
minorhero Posted March 15, 2016 Author Report Posted March 15, 2016 Thank you for the advice! I went with the Infinity blade. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.