Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

MDF Router Table top

Featured Replies

Guys, I live in south Louisiana where we drink our air (high humidity).  My shop is currently in my garage where I use half and my wife's car uses half.  So there's no HVAC system to control temp and humidity.  Now to my question: I'm going to build a router table top.  I was going to use MDF and basically follow the "Norm Abrams" plan.  Should I be worried about the humidity warping or damaging the MDF table top?  Or would I be better off using some sort of plywood?  With either option, I'm sure I'll face the top with formica or some other sort of smooth countertop material.

While on the topic of routers, after I build a dedicated router station, I thought I might add a router table top to my Rigid Table saw.  This way I have one router for most operations and then the router in the table saw top I could just keep a 1/4" round over bit or some other commonly used bit.  Would this be worth my time or not? 

Thoughts??

Thanks for the help!!!

I used two 3/4" MDF boards laminated together for my top, and melamine on top of that, and so far no warping whatsoever. If I had to do it again, I'd use formica instead of melamine.

I have two router tables for the reason you speak of Redfish and also welcome to the forums.

I have MDF's inferior little brother for my router table (particle board) and it seems to work ok. I run into stiffness issues with mine but it's 5/8" only. Some day I'll make a much better table and use MDF or ply. I don't think humidity should bother MDF i'd be more worried about direct moisture contact.

If you laminate the top and the bottom plus seal or laminate the edges and all the faces inside the cutout for the router you should be ok from moisture in the air.

If you can get it buy high density MDF. It's used to make those one piece fake raised panel doors. So it's not going to be available at a big box store. It is harder, heavier and stiffer. 

Add support under the top especially around the router cut out to prevent the top from sagging.

  • Author

Needing more advice:unsure:.  I've decided my table top will be 27"x48".  I've also decided that if I'm going to have 2 routers set up, I might as well have 2 in the table that I'm building.  Since it's 48" long.  So the question becomes, do you place the miter channels and arrange the 2 plates to be parallel to the 27" widths (one on each end of the table) or to the 48" length of the table (with one miter channel running the length of the table)?

Also, is there a standard dimension for placement of the plate and miter channel in relation to each other?

10 minutes ago, Redfish said:

Also, is there a standard dimension for placement of the plate and miter channel in relation to each other?

Two inches apart is pretty common. On the Incra table it's close to 2 1/8".

What fence are you going to install?

 

  • Author

Was planning on building something similar to what Norm Abrams built.  Split rail, higher than the standard fences.  However, after completing the table I may just buy a fence and be done with it.  ;-)

My advice, choose a fence before you even decide the size of your table and/or the placement of the routers. Each fence comes with its own requirements, e.g. an Incra fence requires a lot of space for the Incra positioner.

I built and use Norm's router table. I also built the fence from the plans. It was MDF with Formica faces. It lasted about a year and then wouldn't stay square. I went to a Woodpeckers all aluminium fence. It's a lot more stable. Would have bought and Incra but wouldn't work on my top. Wouldn't waste the time and effort making the fence from MDF.

This is a video I made a while ago of my portable router table:

At a later time I installed a Kreg t-track  and protected the edges with vinyl self-stick door sweep, since it's padded enough for upright storage.

The router is centered on the table top, for added stability, because I'm using a cheap folding stand.

The Incra positioner gets installed on a table extension, when I need to use it, which does not happen to often.

 

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.