sheperd80 Posted March 19, 2017 Report Posted March 19, 2017 I started a commission this weekend for a media console. The client gave a rough sketch of what he wanted, so i revised it into two options. One with a simple beveled overhang, and one with a continuous-grain mitered "waterfall" case. He chose the simple overhang version which i think will go well with his existing decor. I had planned (and bid) for surfaced 4/4 walnut for the entire case but the selection was crap, so i instead went home with a pile of 5/4. Some was surfaced, some rough so right out of the gate i increased my lumber cost and labor  . These nice wide 5/4 boards will make the top, bottom and drawer fronts, and ill go back next week to check the new shipment of 4/4 for the vertical partitions. I didnt want to thickness any more of this than i had to, so i did some pre-milling to reduce the stock a bit. Found some decent grain matches and cut some rough lengths. Then roughly hand jointed the faces just enough for skip planing. Then i straightlined the real bad ones with the tracksaw before jointing the edges. I dont normally joint edges on rough boards but i wanted to be able to safely rip them down a bit before planing. Sent from my SAMSUNG-SM-G890A using Tapatalk Ready to go Now for some planing... Recently emptied dust bag... 2 hours later... All dressed up and ready for dominoes after planing and rejointing. Above you can see a small void i just couldnt cut out. It will be almost impossible to see, so i did a quick dutchman. Good enough, and i still have extra length so ill probably be able to cut it off, but i like to have options until the bitter end. Sent from my SAMSUNG-SM-G890A using Tapatalk 2 Quote
Popular Post sheperd80 Posted March 19, 2017 Author Popular Post Report Posted March 19, 2017 I didnt get a pic but youve all seen domino panel joints before. I used 5 along the length of each joint, 8mm. Just enough to help align things. Ended up adding one in the 2-board panel in a funny spot and it helped. Originally i had hoped to use the 2 rough boards for the top panel but after planing i found alot more sapwood than i thought so that will now be the bottom. The top will be 3 boards that grain match fairly well. My main concern is that the center board is brown while the two outers have a more purple hue. This will get ARS and no color so i really hope i dont have to tone these but we'll see. For some reason on of the boards came off the planer a full 32nd thicker and i didnt catch it until after glue up. So i flattened it out with handplanes. Then a little scraping... And finally got to sanding them down. More to come, thanks for watching :-) Sent from my SAMSUNG-SM-G890A using Tapatalk 4 Quote
wdwerker Posted March 19, 2017 Report Posted March 19, 2017 This post is interesting but did anyone else see huge blank spaces between the text and pictures ? 1 Quote
Chet Posted March 19, 2017 Report Posted March 19, 2017 1 hour ago, wdwerker said: did anyone else see huge blank spaces between the text and pictures ? I am glad to hear this, now I can eliminate me as the problem. Quote
Eric. Posted March 19, 2017 Report Posted March 19, 2017 Yeah same here. No surprise with tapatalk...tapatalk sucks. Quote
Tpt life Posted March 19, 2017 Report Posted March 19, 2017 3 minutes ago, TIODS said: I corrected the spaces Hmm, not effectively for me. I will try a refresh. Looks like one post of two fixed. Thanks for fixing. Quote
..Kev Posted March 19, 2017 Report Posted March 19, 2017 10 minutes ago, C Shaffer said: Hmm, not effectively for me. I will try a refresh. Looks like one post of two fixed. Thanks for fixing. Sorry, for some reason that one didn't change.. Should be fixed now 1 Quote
sheperd80 Posted March 19, 2017 Author Report Posted March 19, 2017 Thanks guys. Sorry about the tapatalk nonsense. I always have to edit multiple times when doing these big write ups in tapatalk, and it seems each time i edit, it adds all these paragraph spacings. Sent from my SAMSUNG-SM-G890A using Tapatalk 1 Quote
Popular Post sheperd80 Posted March 20, 2017 Author Popular Post Report Posted March 20, 2017 Decided to keep moving forward with what i have for now. Ill get the rest of the walnut later this week. But i dug up some 4/4 and got to work on the 2 inner panels. Theyre older, but are really close in color to the top and will be hard to see so i think theyll be okay. Nothin much to see here, it was two 8 foot surfaced boards so i jointed, rough-sized and laid em out for the best possible grain match. Used 6mm dominoes for the panel joints. Ill be stuck with one nasty knot in the dark back area of the cabinet which ill epoxy fill later. I also dug out some old 8/4 falloffs to make the feet. Not sure how long i want them to be so i left them oversized for now. A quick hand jointing Drawing up some curves Off to the bandsaw Spindlization And the best thing i ever learned from mark. The almighty flexible sanding strip! Sent from my SAMSUNG-SM-G890A using Tapatalk 5 Quote
bushwacked Posted March 20, 2017 Report Posted March 20, 2017 dang this is looking great so far! Thanks for all the pics. 1 Quote
sheperd80 Posted March 26, 2017 Author Report Posted March 26, 2017 Back at it! I got the rest of the lumber for the other vertical partitions and ply for the adjustable shelves. Same process as before. Break it down, grain match, mill, glue up. Also started breaking down the sheet goods, mainly to save shop space while i worked on the other parts. With the partitions dry and flat, and everything sanded to 100 i was ready to final size all the main case components. Now for the joinery. Ive never done mid-field dominoes before so it took me some time to work up a good method. All the bays are the same size so i started with a shelf spacer and worked out from center. Layed out the mortise locations on a scrap wood "fence" that will give the bottom of the domino a registration. Then cut some dominoes into the backside of that fence so i could plug it into each location and accurately set up the next row. With all the mortises cut in the top panel, i transfered them to the bottom, checked everything for squarallel and started plunging. This went much faster as i didnt need to do all the spacing steps this time. Laying out the best orientation of the partitions and making dummy marks, ensuring i clamp them down the right way for mortising. Now to cut the mortises in the partitions. I used the same story stick to transfer the mortise locations. I had to make a center mark on the face of the domino to reference as im not using the fence for this. Everything is registering from the bottom of the tool so the fence is not an accurate way to align. With that all done its time for the first dry case assembly. Its always rewarding when things go together with relative ease and line up as planned. Painstaking joinery layout is worth every second. Dont mind the little gaps . The long panels are both slightly cupped after the bipolar weather patterns weve had here in california. But it will easily clamp out. Sent from my SAMSUNG-SM-G890A using Tapatalk 1 Quote
Popular Post sheperd80 Posted March 26, 2017 Author Popular Post Report Posted March 26, 2017 I also started some finish samples on scrap. General Finishes recommends only sanding to 220 so i did just that on one side of the board, and just for kicks went to 320 on the other side. The 320 actually looked nicer after one coat but i will continue coating and decide later. Thanks to all who've posted write-ups on your finishing schedules with ARS. I'm testing a method similar to what Eric and others posted awhile back in the "ARS is Awesome" thread. Sent from my SAMSUNG-SM-G890A using Tapatalk 3 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.