Ronn W Posted May 9, 2017 Report Posted May 9, 2017 I have a table project coming up that is screaming for using dominos. I did not realized until I went on line that Festool was the only manufacturer! OMG$$$. I won't have any money left for Handworks later this month. Anyway, who says you have to justify the cost of a hobby? So, I guess my first questions is, " Honey, will you get this for my Birthday?" Can I attached my ridgid shop vac to the Domino 500?. I have a Rocklers universl adaptor kit (see pic) Does anyone know it thsi will this do the trick?? 2nd question. The 500 does not cut deep enough, for the mortises I will be making in the bread board ends. Idea!---- Is there any wrong with starting the mortise cuts with a 10mm (.3937") bit on the 500 and then extend the depth to about 2" using a 3/8" (.375") pattern bit? I really think that, overall the 500 is a better choice for me than the 700 since most projects are not large tables. Any suggestion greatly appreciated. Thanks. Quote
Eric. Posted May 9, 2017 Report Posted May 9, 2017 You can buy a Seneca kit for the 700 so that it cuts all (or most, not entirely sure) of the 500 size Dominoes. If you're gonna be doing enough big projects that it requires the 700, that's probably the way to go. I used to be anti-700 because for the vast majority of furniture projects the 500 is the right size and I wouldn't want to wield the huge Domzilla all the time if I didn't have to. But economically speaking, I probably have to admit that the 700 is the better choice...IF you'll be doing enough large scale projects to justify it. I had to borrow a Domzilla from a buddy to do this bed I'm working on. The next 20 projects in my queue won't require it. Couldn't justify the purchase. If you don't have a buddy with a Zilla, different story. Your idea with the pattern bit poses a number of problems. Suffice it to say I wouldn't recommend that. You can rig up DC for other extractors...I'm sure that exact scenario has been covered to death on FOG. The downside to using a different brand vac is that unlike with a CT, the power to the vac does not automatically come on when you hit the power on the Domino. Inconvenience. But you could probably a rig a solution for that too or just keep your vac running. First world problem. Quote
rodger. Posted May 9, 2017 Report Posted May 9, 2017 I bought the domino before I had the CT26. I used a ridgid shop vac with a tapered end and it worked just fine. It was bulky and cumbersome, however, which is what lead me to eventually get the CT26. The ct26 is perfect for the domino with its auto DC on/off. As for the domino sizing, you can easily make extra wide dominoes in your shop and do multiple plunges to get the wider mortise. I know Steve does this all the time, and that is where I got the idea! As for depth, you are limited by the machine. If you want to do router cut mortises, I would just go with that approach from the get go. Quote
Eric. Posted May 9, 2017 Report Posted May 9, 2017 I think Ronn was talking about creating a deeper mortise, rather than a wider one...but good point anyway Pug. Which reminds me to remind you...you can always skip the Domino altogether and just use old school loose tenons. Hog your mortises with your spiral bit and router, and make tenons of the same species. I believe Marc just did this on his trestle table video if you need a tutorial on that. A little more time consuming than the Domino, for sure...but it's easy...and free. And one more edit...I just noticed that you're talking about breadboards...kind of don't know why you wouldn't just do them traditionally...it's a skill you should have in your pocket and it's not that challenging once you know all the proper steps. Quote
bleedinblue Posted May 9, 2017 Report Posted May 9, 2017 I use that Rockler kit with my Ridgid vac and my Domino and it works just fine. 2 Quote
Woodenskye Posted May 9, 2017 Report Posted May 9, 2017 Just make sure you remember to turn on the vac. This was the thing that pushed me to buying the CT26. Quote
Jfitz Posted May 9, 2017 Report Posted May 9, 2017 I am just waiting for "The One Project" that makes me decide to get a Domino. As for dust collection.....I use one of these for my shop vac connected to my ROS. Vac always turns on when the sander is on, and it has a delayed shutoff to make sure all dust is collected. My plan is to move it from the wall outlet onto my shop vac directly, so that any tool can just plug in at the shop vac. 1 Quote
Ronn W Posted May 9, 2017 Author Report Posted May 9, 2017 3 hours ago, Eric. said: And one more edit...I just noticed that you're talking about breadboards...kind of don't know why you wouldn't just do them traditionally...it's a skill you should have in your pocket and it's not that challenging once you know all the proper steps. I intend to do the bread board tenons traditionally as soon as I figure out what "traditional" is. As for the mortises, I just thought that I would have better control over cutting the mortises Nice clean cut with no router wiggle) if I did it with the domino to the depth of cut and then switch to the router. Thanks for the comments. 3 hours ago, bleedinblue said: I use that Rockler kit with my Ridgid vac and my Domino and it works just fine. I hate when people tell me what they think I want to hear, but in this case I will make an exception (if it works) Quote
bleedinblue Posted May 9, 2017 Report Posted May 9, 2017 17 minutes ago, Ronn W said: I hate when people tell me what they think I want to hear, but in this case I will make an exception (if it works) If you think I said that just to make you feel warm and fuzzy, I can take a picture of the setup tonight Quote
Brendon_t Posted May 9, 2017 Report Posted May 9, 2017 31 minutes ago, Ronn W said: I hate when people tell me what they think I want to hear, but in this case I will make an exception (if it works) Fortunately on this one, he's right. A normal vac will clear the Domino just fine as long as you get the adapter right. PS, learning to make a traditional breadboard end could be done quicker than reading through this entire thread. They're super easy. Quote
Ronn W Posted May 10, 2017 Author Report Posted May 10, 2017 40 minutes ago, bleedinblue said: If you think I said that just to make you feel warm and fuzzy, I can take a picture of the setup tonight I believe you. I had just heard that festool had its own hose sizes. Thanks. But I like warm and fuzzy, too. That's why I have 2 dogs. 1 Quote
bleedinblue Posted May 10, 2017 Report Posted May 10, 2017 28 minutes ago, Brendon_t said: Fortunately on this one, he's right. A normal vac will clear the Domino just fine as long as you get the adapter right. PS, learning to make a traditional breadboard end could be done quicker than reading through this entire thread. They're super easy. Once or twice a year I am right about something. You're right on the breadboards, too. On my table I built last year, I abandoned the Domino idea and did large floating tenons that were something like 4 inches square. Easy peasy. Although if you need an excuse to buy the Domino... Quote
Klappco Posted May 10, 2017 Report Posted May 10, 2017 I use that Rockler kit with my Ridgid vac and my Domino and it works just fine. I use it with my Festool sander and it works great. Quote
Brendon_t Posted May 10, 2017 Report Posted May 10, 2017 11 minutes ago, Klappco said: I use it with my Festool sander and it works great. Do you have a way to release vacuum? I tried a sander once with a shop vac and it sucked down so strongly to the wood it swirled something fierce. Quote
wdwerker Posted May 10, 2017 Report Posted May 10, 2017 I used a Fein vac w my FT sander for years. Drillled holes in the plastic hose end. That reduce,the,suction enough . Quote
Klappco Posted May 10, 2017 Report Posted May 10, 2017 Do you have a way to release vacuum? I tried a sander once with a shop vac and it sucked down so strongly to the wood it swirled something fierce. Not the best shop vac. Cheapskate strategy! Sent from my iPad using Tapatalk 1 Quote
socoj2 Posted May 10, 2017 Report Posted May 10, 2017 ill sell you my Domino 500 for $750+shipping. its probably done less than 150. its this setup http://www.toolnut.com/festool-574432-domino-joiner-df-500-q-set.html Quote
Eric. Posted May 10, 2017 Report Posted May 10, 2017 37 minutes ago, socoj2 said: ill sell you my Domino 500 for $750+shipping. its probably done less than 150. its this setup http://www.toolnut.com/festool-574432-domino-joiner-df-500-q-set.html Do you have your children for sale, too? LOL You can have my Domino when you pry it from my cold, dead hands. 2 Quote
socoj2 Posted May 10, 2017 Report Posted May 10, 2017 2 hours ago, Eric. said: Do you have your children for sale, too? LOL You can have my Domino when you pry it from my cold, dead hands. I want to buy the large one. I mainly do large furniture. Quote
Ronn W Posted May 14, 2017 Author Report Posted May 14, 2017 On 5/10/2017 at 7:49 AM, socoj2 said: ill sell you my Domino 500 for $750+shipping. its probably done less than 150. its this setup http://www.toolnut.com/festool-574432-domino-joiner-df-500-q-set.html Sending you a private message. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.