Marmotjr Posted May 12, 2017 Report Posted May 12, 2017 Another little turning project I'm working on. End goal is a coffee travel mug. Bought an insert from amazon, and It just showed up. Was going to be a Mother's day gift, I'm hoping I can make the deadline! Using a bunch of scraps I have laying around the shop, plus a bunch of pen blanks from a grab bag I picked up a while ago, I'm going to glue up a segmented blank. All the rings are going to be the same size, so I'm going to cut all the different scraps into the same size segments and toss them all into a hat. I'll grab a dozen for each ring randomly. The alignment of the rings won't matter as it's supposed to be patchwork. Scraps I'll be using: Along with the unknowns from this thread, There is Larch, Oak, Walnut, Pine, Locust, Paduak, Birds Eye Maple, Spalted Bird's Eye Maple, Poplar, Tulipwood, Rosewood, and probably a couple other's I'm forgetting. Jointing two sides each for the glue up, and to give me the option of picking which grain I like the best. Using my small stock jointing jig, which has found use as a small taper jig too. And because the math is calling for 1.1" inch thick segments, and most of these blanks are barely .75" thick, I'm laminating all of the smaller segments to pine to fill out the size of the interior. I don't care if the inside is all pine or ugly, it'll be covered up by the stainless steel mug insert. Quote
Marmotjr Posted May 13, 2017 Author Report Posted May 13, 2017 Soooo... if I say I want to try another "simple" scrap box project...... shoot me. This got way complicated fast. But I'm in the home stretch! And I haven't even begun the ring glue up..... and it's "due" tomorrow! But, I'm on a 3rd shift sleep cycle, so I can get the rings glued up, sanded, and start the glue up on the lathe before I go to sleep. Then when I get up tonight, I can do all the turning and finishing, and won't have to run any loud tools while the others are asleep. Here you see some of the smaller random pen blanks glued to a pine board, there's another 3 boards gluing up off camera. The pine is there to add inside thickness to the final glue up. The glued up stock was again run through the jointer sled, and then crosscut apart, making the blank and pine flush. While that was drying, I mounted and trued up a Maple/Cherry (no, it's really maple @Eric :)) block for the base. I didn't take a picture of it trued, with a tenon on the back side to mount in the chuck jaws, it's mounted using a wormscrew right now. Just imagine this, but round. After all the blanks had dried, and been cut apart, I ran them though the drum sander. I was dreading having to set this up again, but then I realized I have to do it for the rings anyways. Here's where things started to piss me off. I've made the first cuts on each piece, and I realized that I can't just flip the stock over and do the next cut like you normally would with stock that is one wood. (I'd already cut up some of the larch and walnut, I held off on the pine, only using that if I didn't have enough segments.) So it turned out that in order to keep the good wood on the wide side of each segment, I'd have to trim off a small piece to "reset" the angle for each cut. Given these blanks are only 5" or so long, there wasn't a lot of material to spare. I ended up getting scary close to the blade, using a pencil to hold the piece. This was a total pain in the ass. Here's what about 20% of the scrap looks like. (Plus one good stock) And here friends, is 111 segments with the show side of each segment on the wide side. Math says I only need 96, so I have some extras if I find some bad ones, and then some for an extra ring if needed. I was worried about needing to use another section of the maple as a rim (If I screw up the top tenon, I just may still), but I have plenty of segments. 2 Quote
Marmotjr Posted May 13, 2017 Author Report Posted May 13, 2017 I grab my box of hose clamps, start the glue up, and all of a sudden, I'm out of hose clamps. Doh! I used a few on the DC system! Well it's a good thing the clamps will come off before I need to sand these. Rings drying, next step is sanding. As I'm gluing these up, I realize the boundary between the outer and inner layers is really wide. In my attempt to give myself enough fudge room for sanding and misalignments, it's going to be awfully close to that inner layer to get this small enough to fit in a cup holder. 1 Quote
Popular Post Marmotjr Posted May 13, 2017 Author Popular Post Report Posted May 13, 2017 Final glue up is under way. I wasn't going to post till it was done, but I'm waiting 10 minutes between each ring to let the glue set enough so I can slap on the next ring with minimal fuss. I'm exhausted. Yes, A vertical press would be more effecient, but I don't have one setup right now, and I've tried to do a makeshift one in the past, and it didn't go as well as using the lathe as a press. Right now, I'm too tired, and that's when mistakes happen, and I don't have time for mistakes. I already shaved off the top of 1 fingernail on the drum sander (That's my quota I usually do when using this thing, it is not OSHA compliant!), I don't need more issues. Anyways, as I said, sitting for a moment, and I figured I share how cool these rings looked post sanding. The wonkiness of the center is a little off putting, but I like how the colors look. Again, I love this part of a project, when the effort is starting to pay off and you can see the end result coming. Gives me the boost I need to keep going. I've bailed on other projects (I have like 7 unfinished bowls on the shelf) when I've seen it wasn't going in the right direction and my heart just wasn't in it anymore. Yup I'm tired, I'm rambling worse than ever, here's the damn pic already. 4 Quote
Marmotjr Posted May 13, 2017 Author Report Posted May 13, 2017 30 seconds to glue a ring, ten minute timer on the phone, timer goes off, hit stop, finish reading page I'm on, forget about glue up for 5 minutes, then glue the next ring. This is gonna take forever. Slap happy tired now. Your tolerance of my rambling is appreciated. 2 Quote
ghost Posted May 13, 2017 Report Posted May 13, 2017 4 hours ago, Marmotjr said: Soooo... if I say I want to try another "simple" scrap box project...... shoot me. This got way complicated fast. But I'm in the home stretch! And I haven't even begun the ring glue up..... and it's "due" tomorrow! But, I'm on a 3rd shift sleep cycle, so I can get the rings glued up, sanded, and start the glue up on the lathe before I go to sleep. Then when I get up tonight, I can do all the turning and finishing, and won't have to run any loud tools while the others are asleep. Here you see some of the smaller random pen blanks glued to a pine board, there's another 3 boards gluing up off camera. The pine is there to add inside thickness to the final glue up. The glued up stock was again run through the jointer sled, and then crosscut apart, making the blank and pine flush. While that was drying, I mounted and trued up a Maple/Cherry (no, it's really maple @Eric :)) block for the base. I didn't take a picture of it trued, with a tenon on the back side to mount in the chuck jaws, it's mounted using a wormscrew right now. Just imagine this, but round. After all the blanks had dried, and been cut apart, I ran them though the drum sander. I was dreading having to set this up again, but then I realized I have to do it for the rings anyways. Here's where things started to piss me off. I've made the first cuts on each piece, and I realized that I can't just flip the stock over and do the next cut like you normally would with stock that is one wood. (I'd already cut up some of the larch and walnut, I held off on the pine, only using that if I didn't have enough segments.) So it turned out that in order to keep the good wood on the wide side of each segment, I'd have to trim off a small piece to "reset" the angle for each cut. Given these blanks are only 5" or so long, there wasn't a lot of material to spare. I ended up getting scary close to the blade, using a pencil to hold the piece. This was a total pain in the ass. Here's what about 20% of the scrap looks like. (Plus one good stock) And here friends, is 111 segments with the show side of each segment on the wide side. Math says I only need 96, so I have some extras if I find some bad ones, and then some for an extra ring if needed. I was worried about needing to use another section of the maple as a rim (If I screw up the top tenon, I just may still), but I have plenty of segments. ir is making my head spin looking at this pic and trying to figure out how this becomes a "bowl" !!!! LOL looking good so far 1 Quote
Marmotjr Posted May 13, 2017 Author Report Posted May 13, 2017 I think it looks like a pile of spoiled candy corn. And I happen to like candy corn. If you ever see the candy corn flavored M&M's, try them, it's life changing. Sorry... Quote
Marmotjr Posted May 13, 2017 Author Report Posted May 13, 2017 39 minutes ago, ghost said: ir is making my head spin looking at this pic and trying to figure out how this becomes a "bowl" !!!! LOL looking good so far One ring left, and I'm beat, so I was going to post this after I got the last ring on, but this will make better use of my time. And here's the rough blank of the mug: Now I, and the glue, need some sleep before I tackle this thing tonight. Quote
Marmotjr Posted May 14, 2017 Author Report Posted May 14, 2017 Blank almost trued up! Really happy about how this turned out! And now that she's home, I can size her cup holders in her car (Hmmm.... kinky), and the blank is fine! Woohoo! Cool little pic of the shavings. I actually like this pic so much it's now my desktop wallpaper. This is a reduced version of course, the original is 6k x 4k, so no posting that. 1 Quote
Popular Post Marmotjr Posted May 14, 2017 Author Popular Post Report Posted May 14, 2017 Hogging out the inside with a 2 1/8" forstner. Insert is 2 3/16" at the base, so it's the perfect place to start, less manual labor. Weeee! Wood chips! Buried deep. I set the bit so I know I'm at the correct depth when the flat edge of the blank is flush with the flat on the back of the chuck. Just glad the chuck fit! After some more hollowing, most of the pine in the top half is almost gone, but it's still there, and needed, in the bottom half. Test fitting the insert. rub sharpie marker on the side and turn it in the blank. The ink transfers to the inside of the blank on the high spots. Weeeee! It fits! Tenon for the lip of the insert. Shaping and measuring for the cup holder size. NOOOOOOOOOOOOO! SAWDUST DIAPERS! A CATCH! Well, no choice, gonna have a scar on it. I'm hoping it will add character rather than be a flaw. I'll keep telling myself that. After a little clean up. Final shape, sanded to 220. Now to flip over, and clean up the bottom. 5 Quote
Marmotjr Posted May 14, 2017 Author Report Posted May 14, 2017 SON OF A B.... There's a 3/16" gap between the largest size my small chuck jaws can fit, and the smallest size my large jaws will go. Guess what falls into that range?!! GRRRRRRRRRR Improv time. Custom made jam chuck it is. Quote
Marmotjr Posted May 14, 2017 Author Report Posted May 14, 2017 Always thought my glue block needed to lose some weight. It's now a jam chuck. Don't worry it'll be a glue block again tomorrow. Tenon is now revealed on the bottom. Kind of a chore getting the tailstock to center up properly, or rather, getting the mug centered. Tenon removed. As I feared, the wormscrew hole has broke through. No Biggy, I was hoping it wouldn't, but planned for it to do so. Sawdust plug applied, whole mug sanded to 220. HOLY POPPING GRAIN BATMAN! First coat of 1lb shellac, and WHAM! all the colors and grain and figure (as much as you can have in such tiny pieces) just exploded. I'm pretty sure one of the birds eye's winked at me. The Oak is glowing, same with the paduak. 2 Quote
Marmotjr Posted May 14, 2017 Author Report Posted May 14, 2017 10 coats or so of Insta Flex Medium CA (it's rubberized so it has some flex, makes a very nice feeling pen in the hand, hoping it will do the same on the mug). Still wet from activator, and prior to buffing to 12,000 grit. I was hoping for only 5 coats, but some of the segments were just drinking in the CA. It will be way less fugly when it's polished. 2 Quote
Popular Post Marmotjr Posted May 14, 2017 Author Popular Post Report Posted May 14, 2017 Finished taking the glamour shots, and she woke up. Had time to put it back in the box, slap a ribbon on it, and give it to her. Happy Mother's day Dear. She was estatic. 13 Quote
Tpt life Posted May 14, 2017 Report Posted May 14, 2017 I was unsure until the final shots. Great project, good job. 1 Quote
Marmotjr Posted May 14, 2017 Author Report Posted May 14, 2017 20 minutes ago, K Cooper said: Really cool project. Very well done! Thank you sir. 6 minutes ago, C Shaffer said: I was unsure until the final shots. Great project, good job. So was I. Thank you. Post project thoughts: 1) Might need to try another CA application method. I wasn't too happy with the outcome, I was going for gloss, and it's semi-gloss. But it still looks great. On pens it always gloss, but there's a heck of a lot more surface area. More research is required. 2) The catch was a very avoidable mistake. I brought the gouge close to the piece without having it on the tool rest first. It was accidental, but that's turning 101. That's Turning Law #2 according to Keith Rowley. I broke that one hardcore. Bad Marm. 3) The hole in the bottom might have been avoidable, but I'd need thicker stock or a shorter wormscrew. If I had more time, the block would have been first mounted to a glue block, and then turned. But I didn't have the time to wait for the glue to fully set up (12+ hrs), and I'm not turning anything on questionable glue. 4) Most of the rest of the hiccups were from 50 new ideas I tried to implement for the first time. Now that I have those worked out, any future projects like this will go a lot smoother. 5) I really need to figure out a safer way to use this drum sander (A real one is out of the question for right now). The results are good, but I sanded off two finger nails this time. I thought about using something like a shepherd's crook, but the chance of it catching and having it launched across the room is too great. I semi launched one of the rings. Over all, very pleased with the result. Quote
shaneymack Posted May 14, 2017 Report Posted May 14, 2017 Turned out awesome! Great gift idea, I'm sure she will get great use out of it for years. Sent from my SM-N910W8 using Tapatalk 1 Quote
wtnhighlander Posted May 14, 2017 Report Posted May 14, 2017 That looks great! How could she not be pleased? 1 Quote
Marmotjr Posted May 14, 2017 Author Report Posted May 14, 2017 5 hours ago, Pug said: Very unique - nice project. Unique, another word for ugly. It's supposed to be ugly. You're supposed to look at it, make a weird face, then want to examine it closely. 2 Quote
lewisc Posted May 15, 2017 Report Posted May 15, 2017 A great way to use up scraps. Looks good. 1 Quote
Ronn W Posted May 18, 2017 Report Posted May 18, 2017 impressive. I am not a turner but I really like it. 1 Quote
Marmotjr Posted May 18, 2017 Author Report Posted May 18, 2017 So I might have a scrap box special special project in the works. The 7 year old is wanting a fidget spinner. I have a box of rollerblade wheels that I got cheap for a RC land yacht I was making a while ago, and have been using the bearings for various projects since. I handed her one of the whole wheels as a spinner, and her response was "But it's round". SO now I'm eyeballing those small scrap wedges I have sitting in the burn box thinking how I could glue those together to form some sort of start shape and mount a bearing in the middle...... Quote
wtnhighlander Posted May 19, 2017 Report Posted May 19, 2017 Or just spindle sand some chunks out of the skate wheel? 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.