Mike Vee Posted May 21, 2017 Report Posted May 21, 2017 Hi Everyone! I'm back on a new project! I'm building a bookcase for my wife and right now I need a table saw (I am cutting A LOT of boards for the shelves, beadboard backing, etc) and I realized my circular saw would not cut it in terms of time constraint. I also need to give up my circular saw for some time because for some reason, the saw is actually crooked (the measurement from the edge to the blade is off by 1/8" when compared from the back of the blade to the front), so I need to take it to a Skil Authorized repair center to get it fixed. So back to the main question: I'm interested in the Bosch 4100-09 because a friend of mine highly recommends it. It is kind of out of my price range ($600) but I am willing to spend money on it if it's worth it. On the other hand I noticed that the Rigid R4513 also has stellar reviews and I found 2 people who are willing to sell it for a pretty decent price. 1 is for a like new looking R4513 for $300 and the other is for a somewhat used R4513 for $200. What I'm most concerned about is that I want a saw that has a reliable fence and also one that will last a very long time (hell, I would hope i die before the table saw dies) but yeah, I'd love to get your opinions and advice on which one I should go for. Thanks! Quote
Popular Post Eric. Posted May 21, 2017 Popular Post Report Posted May 21, 2017 People seem to love their Ridgids but I think Bosch probably makes higher quality products in general. If I were in your shoes I'd probably test drive both of the used Ridgids, buy the best one, and put the savings from not buying a new Bosch into a piggy bank labeled "Cabinet Saw."...and keep putting money in there until you can buy a proper saw. 3 Quote
knotscott Posted May 21, 2017 Report Posted May 21, 2017 First question - Are you specifically looking for a portable jobsite saw, or are you looking at those due to price? If you don't need portability, a larger full size cast iron saw with a belt drive induction motor has several advantages over the smaller jobsite saw, including long term reliability as well as feasibility of a repair if ever needed. The ABCs of Table Saws BTW, don't take online reviews as gospel....it's estimated that about 30% are not legit. Those that are legit may or may not be from credible users. 2 Quote
Alan G Posted May 21, 2017 Report Posted May 21, 2017 I bought the Bosch 4100 on the gravity stand about 6 years ago. I was going to be remodeling a house we just bought after living in NYC with infant twins for 2 years. We needed more space and wanted out of the city. Needless to say I was looking for some larger tools. The Bosch was a great saw and served me very well. It is a contractor saw though. You need to realize its place in the market. For that purpose it is an excellent saw. However, as I started larger projects, outside of the remodel world, it started to show its limitations. The fence was a big one. I struggled to keep the fence aligned and locked down. The small area of the table made some operations difficult and at times dangerous. The gravity stand was great but stability was an issue. Lastly, even with a thin kerf blade, the saw bogged down at times while ripping larger stock. I sold the bosch a few years ago when I bought a sawstop pcs. If you are looking for the portability and storage options of a contractor saw I would recommend the Bosch. If it is just going to sit in a shop space, and a full size cabinet saw is out of the question, I would say at least look at a hybrid saw from the Grizzle. i have never used one but for a few bucks more than the bosch w/stand it looks like you can get more saw. Hope that helps. Happy to answer any other questions you have about the Bosch. 1 Quote
Popular Post wtnhighlander Posted May 21, 2017 Popular Post Report Posted May 21, 2017 Mike, unless portability / size is the deciding factor, I would recommend avoiding the small job site saws you mentioned. For stationary work, I recommend at least the Rigid 4512 or other brand equivalent. If current retail doesn't fit your budget, and you just can't wait, Craigs List often has these type saws listed around 1/2 retail price. If you go that route, do some research on what problems to look out for. 4 Quote
Mike Vee Posted May 21, 2017 Author Report Posted May 21, 2017 I think i failed to mention that the reason I'm looking for a portable table saw is also due to space constraints. The price is also part of my concern. Initially I didn't want to spend more than $500 but from my friends' adivces, I noticed the real decent ones started at closer to $600. I have a 2 car garage but the space is very limited, so I need something that can be put away at the end of the day.. i don't know if I'll be cutting anything massive but the most I'm doing now is to rip 8' lengths of 1" thick common boards and beadboards. I will test out the rigids today and see if it's worth it. I had a few friends who recommend them as well. I figured that as long as it can handle a hobbyist like me it's probably all I'll need. I won't be building a house anytime soon but I will be trying to go into cabinetry in the future. I did like the Bosch a lot. The only thing that bummed me about it is the fact that it can't cut a 4x4 in 1 pass. in regards to larger rips, I figured that once I need an extension, I can get a Rousseau table and extension side table to handle wider rips. what do you think? you guys are super helpful again as usual! Thanks! Sent from my SM-G930F using Tapatalk Quote
Eric. Posted May 21, 2017 Report Posted May 21, 2017 23 minutes ago, Mike Vee said: the real decent ones started at closer to $600. $1500 FTFY Get those cars out of your SHOP, homie! 1 Quote
Mike Vee Posted May 21, 2017 Author Report Posted May 21, 2017 FTFY Get those cars out of your SHOP, homie! hahaha I can't afford 1500 (otherwise I'd get a sawstop lollll) Sent from my SM-G930F using Tapatalk Quote
Tpt life Posted May 21, 2017 Report Posted May 21, 2017 59 minutes ago, Mike Vee said: hahaha I can't afford 1500 (otherwise I'd get a sawstop lollll) Uh, you find a SS for $1500 somewhere? For $1500 you can be in the 3-5 HP 10" Grizzly offering. 1 Quote
Mike Vee Posted May 21, 2017 Author Report Posted May 21, 2017 Uh, you find a SS for $1500 somewhere? For $1500 you can be in the 3-5 HP 10" Grizzly offering. I think I saw one on Craigslist for about that much but it's the portable one, not the cabinet saw version. which model grizzly are you recommending? I don't know if I can afford the 900 bucks unless I luck out and find one closer to 500-600 Sent from my SM-G930F using Tapatalk Quote
Tpt life Posted May 21, 2017 Report Posted May 21, 2017 22 minutes ago, Mike Vee said: I think I saw one on Craigslist for about that much but it's the portable one, not the cabinet saw version. which model grizzly are you recommending? I don't know if I can afford the 900 bucks unless I luck out and find one closer to 500-600 Sent from my SM-G930F using Tapatalk I bought the 1017 for 900 which included a mobile base and freight charge. That translates to a $700 saw with a sketchy alignment history but has a better than contractor trunnion etc. It is not as highly recommended as the 1023. @TIODS is another with the 1017. I don't want to push you outside your budget, but I will never buy a contractor saw for my shop again. They are too limiting for what I do. 1 Quote
Popular Post wtnhighlander Posted May 21, 2017 Popular Post Report Posted May 21, 2017 Not trying to rain on the parade, but what you say you want to do is pretty difficult, and somewhat dangerous, on a tiny job-site saw. I know there are plenty of folks on Youtube that use them for all sorts of things, but almost 100% of the time, they are built in to some larger table, which defeats the size requirement. Frankly, I feel safer ripping 8' stock with a circular saw and edge guide, than on a job-site saw. And yes, I used to own one. I still have just a 'contractor' style saw, but the larger, cast iron table, solidly-locking fence, and smooth induction motor make a world of difference. 4 Quote
Woodenskye Posted May 21, 2017 Report Posted May 21, 2017 I would look at the Grizzly hybrid, which is closer to $800, but is in my opinion a lot better than both the Rigid and Bosch. 1 Quote
wtnhighlander Posted May 21, 2017 Report Posted May 21, 2017 Oh, I also wanted to mention that cutting a 4x4 in one pass is going to require a table saw that supports a 12" or greater blade. You won't find that in a portable. 2 Quote
Mike Vee Posted May 21, 2017 Author Report Posted May 21, 2017 man, it's so tempting to get a much nicer table saw but I can't really afford something so expensive. I also don't have any space for a cabinet saw. I do have an edge guide but the massive problem I have is that currently it can't cut straight. I think cutting pieces this long would be a bit easier with having my wife help pull the board along as it gets further out. but right now space abf money is tight so I can't really get a high end product yet... Sent from my SM-G930F using Tapatalk Quote
Popular Post Eric. Posted May 21, 2017 Popular Post Report Posted May 21, 2017 10 minutes ago, Mike Vee said: having my wife help pull the board along as it gets further out. Do NOT do this. Period. 4 Quote
Mike Vee Posted May 21, 2017 Author Report Posted May 21, 2017 ohh no, not straight pull. from the side. always from the side. I've established this with her already that she is never allowed to stand directly in front of the table saw when it's running. Sent from my SM-G930F using Tapatalk Quote
Eric. Posted May 21, 2017 Report Posted May 21, 2017 One person per cut. If you want her to help *support* the board as it exits your saw to help prevent it from tipping down...that's one thing. But there should be no pulling or pushing or exertion of force in any which way from anyone except the person who's making the cut. Two people working at a table saw is a recipe for disaster. Generally speaking, if a board is too big for you to handle alone at the table saw, you should be taking a different tool to the wood, rather than the wood to a tool. 2 Quote
knotscott Posted May 21, 2017 Report Posted May 21, 2017 An extension can add rip capacity to a jobsite saw, but it won't add space in front of the blade, or mass. The larger landing zone makes it easier to get the board settled before the wood actually reaches the blade....that alone is a pretty significant advantage. Quote
Mike Vee Posted May 21, 2017 Author Report Posted May 21, 2017 One person per cut. If you want her to help *support* the board as it exits your saw to help prevent it from tipping down...that's one thing. But there should be no pulling or pushing or exertion of force in any which way from anyone except the person who's making the cut. Two people working at a table saw is a recipe for disaster. Generally speaking, if a board is too big for you to handle alone at the table saw, you should be taking a different tool to the wood, rather than the wood to a tool. Thanks that makes sense. I'll have to reassess my plan then Sent from my SM-G930F using Tapatalk Quote
Alan G Posted May 21, 2017 Report Posted May 21, 2017 49 minutes ago, Mike Vee said: I do have an edge guide but the massive problem I have is that currently it can't cut straight. As an interm solution, until your budget get to where you want, go grab a new circ saw and redo the edge guide. You can get a decent one for 100-150 bucks. Quote
Mike Vee Posted May 21, 2017 Author Report Posted May 21, 2017 yeah I was looking at getting a bosch circular saw. my friend just showed me that bosch donates a large amount of their profits to charity which I find very impressive Sent from my SM-G930F using Tapatalk Quote
Eric. Posted May 21, 2017 Report Posted May 21, 2017 1 minute ago, Lester Burnham said: I've been eyeing the Dewalt 7491RS because it's got a larger "landing zone." From the reviews I've read and what I've seen in stores, the fence is pretty awesome. Both it and the blade are easy to adjust for squareness. I just don't want that stand and I can't find any place selling just the saw. I had that saw when I was a DIY guy. Or at least it looked basically identical. I don't remember anything about the fence being awesome. I wouldn't want to build furniture with any contractor saw. Too limiting. Not to be discouraging, but if it's time to upgrade...let's upgrade right. 1 Quote
Mike Vee Posted May 21, 2017 Author Report Posted May 21, 2017 I think that's what's hurting me the most right now, the physical space constraints. I have to be able to put it away in a corner at the end of the day Sent from my SM-G930F using Tapatalk Quote
Eric. Posted May 21, 2017 Report Posted May 21, 2017 8 minutes ago, Mike Vee said: I think that's what's hurting me the most right now, the physical space constraints. I have to be able to put it away in a corner at the end of the day Well Lester works in a closet so I get it...but if you have space to roll a saw around...even cabinet saws you can get mobile bases for. 2 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.