Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Wall Hanging Tool Cabinet

Featured Replies

  • Popular Post

Been a busy summer. Not much woodworking, but I've been doing some shop upgrades (soundproofing insulation in the ceiling, new drop ceiling with a better sound rating, reconfigured dust collection ducting). I figured it was a good time to finally build a tool cabinet that I've been wanting to build for a while. Going to use this design from Fine Woodworking.

I have some nice crotch figured walnut that I want to use for door panels and my original plan was to do the whole thing in walnut. The walnut at my lumberyard (which is usually great) was crap though. Except for a few ridiculously priced slabs, all of the walnut had tons of knots and sapwood, despite still costing a fortune. So I decided on the fly that I would pick up some butternut for the cabinet instead. I figured being close cousins with walnut, it would make a nice contrast with the crotch walnut panels, without being too much of a contrast.

Never worked with butternut before. Kind of sucks, actually. My planer ate it up and left fuzzies all over the boards, despite having very sharp blades and taking shallow passes. It hand planes beautifully though. 

Got the boards for the main case milled and cut to size, then I surface prepped the insides of the boards to get ready for dovetailing. Few passes with my #5 to get rid of the planer fuzzies and then sanded to 220 with the ROS:

IMG_0688.JPG.09d745243696942a6fe67bb4f2fcda4c.JPG

I'm hoping I can start dovetailing tomorrow.

 

  • Replies 59
  • Views 15.1k
  • Created
  • Last Reply

Top Posters In This Topic

Most Popular Posts

  • Got a little bit of shop time last night. Did one set of tails & pins for the main case. The half tail is on the back of the case and is intended to hide a rabbet into which the back panel will fi

  • Some progress to report. I made two more panels -- for a total of six -- to give me some options. Glad I did, too. I ended up sanding through one veneer and, as I mentioned earlier there was a crack i

  • Been a busy summer. Not much woodworking, but I've been doing some shop upgrades (soundproofing insulation in the ceiling, new drop ceiling with a better sound rating, reconfigured dust collection duc

Posted Images

  • Author
  • Popular Post

Got a little bit of shop time last night. Did one set of tails & pins for the main case. The half tail is on the back of the case and is intended to hide a rabbet into which the back panel will fit. 

Tails cut in the background and pins laid out in the vice:

IMG_0690.JPG.9df15a387dd7bc08ee926865075e5e0b.JPG

I typically chop out the waste with a chisel, but this time I decided to try cutting it out with a fret saw (also gave me a convenient excuse to pick up a Knew Concepts saw, which I've been wanting for a while). Verdict: way better than using only a chisel! It's so much faster, plus less sharpening I have to do on my chisels. Definitely the way I will be doing dovetails from now on. The only downside is I snapped my only blade (forgot to order replacements), so I need to pick some new ones up. Any suggestions on good blades?

Here's a pic of the boards, mid-dovetailing, with the pins only partially seating:

IMG_0691.JPG.2cf0a7278715a7acff160da6cf070dcb.JPG 

After some fiddling:

IMG_0695.JPG.330abbccd429423a7af42f77f4ba9286.JPG

A little more work to do, but they're almost there. If you look closely you might see some blood. It's a new technique I'm working on. You might have heard of the pencil smudge trick for determining where more material needs to be removed, this is similar, but far more painful...

I've been using scrollsaw blades in a jeweler's saw for years. Lusted after a Knew Concepts saw but haven't had a project that would justify pulling the trigger on one yet. Really wanted a titanium one but I don't think they are available anymore.

I found that high tension, a light touch when cutting and maintaining a quicker stroke gets me the best results right up till it grabs and the blade snaps. That's why I keep around 2 dozen of each different blade on hand. Only practice lets you build speed and accuracy.

  • Author

Good idea about the scrollsaw blades. The Knew Concepts saw is pretty awesome. I have an old crappy home center saw that I have used for things in the past and it's a night and day difference. Easier to control, keeps tension better, and it just looks cool (I'll admit this was one of the reasons I got it, I am building a tool cabinet to display my tools, after all...)

 

 

Sent from my iPhone using Tapatalk Pro

And I'm building a cabinet to consolidate my tools.  From 5 wall hangers into one decent size floor model.

  • Author

You journaling it? I'd love to follow along.

 

My previous storage method was to leave my tools wherever the hell I happened to have them last, and then spend 20 mins trying to find it later.

 

 

Sent from my iPhone using Tapatalk Pro

Coming along nicely! I made a tool chest out of Butternut and agree the power tools do leave a bit of fuzz but the hand tools work the wood beautifully. Re fret saw blades for DT's, I usually use a 12 TPI skip tooth scroll saw blade

  • Author
  • Popular Post

Finished dovetailing the main case, which is 10" deep. The doors will be 3" deep to accommodate more storage:

IMG_0702.JPG.1a121e04ab4157915319aabee769f7e0.JPG

Found a new use for systainers; here's a shot of where the tool cabinet will hang when it's done: 

IMG_0711.JPG.7e1e73747cc34901bb9f7bab865956f1.JPG

Ignore the clutter, missing ceiling tiles and all-around massive mess... This cabinet build is part of a larger shop upgrade, so hopefully, when it's all done, everything will be neat and organized. 

On 8/24/2017 at 0:09 PM, Dknapp34 said:

You journaling it? I'd love to follow along.

 

My previous storage method was to leave my tools wherever the hell I happened to have them last, and then spend 20 mins trying to find it later.

 

 

Sent from my iPhone using Tapatalk Pro

Nah, just gonna do a finished product.

  • Author

Update time:

Finished the frames for the 3" deep doors:

IMG_0800.JPG.f56c396da5a513df50a9c1e2323a7607.JPG

IMG_0802.JPG.5bbb0583c924eecc7c3d8f5681b7c431.JPG

Also finished the face frames for the doors. Frames are dominoed together. Had a little bit of a resawing issue with the crotch walnut panels I was planning on using. Thought I was going to be able to get 4 panels out of two boards, but it looks like I am only going to be able to get 2. Since I only have 2 of the heavily figured crotch panels, I either need to try and find some similar crotch boards, or use this other piece I have (the one on the left below), which also has some crotch figure at the bottom. The original plan was to have both doors look like the one on the right (bottom panel is darker because it has mineral spirits on it). I'm still trying to figure out if I like the look of the two different doors together. Love to hear others' thoughts...

IMG_0799.JPG.6c6c94ed27b415376e3cb76c71f967b3.JPG 

 

Can you resaw the crotch piece into veneers?  Can't say I'm a fan of those two boards together.  They may as well be two different species.

  • Author

Think you're probably right about that. Unfortunately, I don't have capacity on my band saw to resaw them. I'll look around online and see if I can find something with a similar grain pattern. Might just have to save those panels for another project and get something different entirely. Worst case scenario, I can buy some veneer and make veneered panels.

  • Author
  • Popular Post

Ordered some interesting looking crotch figured veneer for the panels from VeneerSupplies.com. We'll see how it looks in real life when it arrives. In the meantime, I did some test fitting of my planes on the plane till:

IMG_0819.JPG.0f2b1047e1fd0e7690cb154f542f92c6.JPG

 

  • Author
  • Popular Post

Veneer came over the weekend. Wasn't sure what to expect, since I've not worked with veneer before, but it is some pretty beautiful stuff. Very happy with my purchase. The veneer was pretty wonky when it arrived, so I sprayed it down with veneer softener and have been pressing it between melamine, with layers of paper towels and fiberglass window screen material, pressed between some cauls. I put a slight convex curve on the cauls using a hand plane so that when I clamp the ends there is good pressure in the middle:

IMG_0830.JPG.80b2ecd9f0c6d2fe4bfa38a23d299332.JPG

Here's the veneer, mid-flattening (still feels cold to the touch, so it needs a little more drying time):

IMG_0828.JPG.04fac3bdbd58b4b750d07d2036eae81d.JPG

Here's the pattern I am thinking about using for the door panels:

IMG_0829.JPG.2dedd94012b14d729a92f9ce7e833c04.JPG

Should be dry in another day or so, after which I will glue them to a plywood substrate with a cheaper veneer on the back of the panels to balance it out.

 

That looks wicked ! Fresh paper helps w drying.  What kind of glue did you decide on? You might want to do a little test run if you have some spare veneer. 

Way to go the extra mile.  Totally gonna be worth it.

  • Author
1 hour ago, wdwerker said:

That looks wicked ! Fresh paper helps w drying.  What kind of glue did you decide on? You might want to do a little test run if you have some spare veneer. 

Was thinking about using Titebond Cold Press Veneer Glue. Have never used it before, but they carry it at my local woodcraft. My plan was to glue up the back side of one panel first as a test run.

  • Author
9 hours ago, wdwerker said:

Smart move. Going to use the same clamps & cauls ?

Nope. Planning on using 4 cauls across the top and bottom, and the panel will be sandwiched between two layers of 3/4" mdf on each side. Hopefully that will give me enough evenly-distributed clamping pressure. 

Should work I think. Don't overtighten the clamps. Even pressure is what you want. If overtightened you can get lumps where the glue is forced out from under the cauls and glue starved stripes under the cauls. Apply the glue as evenly as possible. 

  • Author
  • Popular Post

Glued up the panels, here's the set up I used:

IMG_0837.JPG.f6b3e522a4e6319f176ede5349509b69.JPG

Here's one of the panels with a coat of ARS:

IMG_0839.JPG.ce84183813aedd39d60cd8022473241d.JPG

Two of the panels have slight cracks in the veneer that didn't quite glue up perfectly. You wouldn't notice unless you were looking closely, but I have two extra sheets of veneer so I'm just going to glue up two more panels. Might as well do it right. 

In the meantime, I started cutting the mortises for the hinges. Doing this the old fashioned way with a chisel, because I'm making a hand tool cabinet and it just seemed like the right thing to do. 

IMG_0840.JPG.be56168c19ac849f2a97b2c7ef8fad37.JPG

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.