Recommended Posts

Posted

Still in the planning phase, so this is just for feedback for now, but it will eventually turn into a journal. 

I'm planning on making some night stands for the GF, I plan on using mainly maple, some nicely figured stuff if I can acquire it cheaply (doable proposition with work and a quick lumber yard trip), but I want to use Cherry as an accent wood.   I'm thinking of inlaying a thin border of cherry on the top surface (maple) that matches the outline of the top, maybe set in an inch or so, and the drawer pull will either be turned or cut cherry, so not a lot of cherry so far, just a bit of color splash.

But I'm thinking of adding some cherry to the legs.   Legs will be around 1.5" square at the top, and below the shelf (in the upper half below the drawer) they will taper down to about 3/4" -  1" square at the bottom, but only from two sides.  Maybe 4 if I like the look, I dunno.  Cherry is facing the outside corner of each leg. 

So I have to questions.  1) Hows this look to you guys and 2) Technically, how would this type of leg work/act during production?:

leg1.jpg.4b306075907eae971592cfd46acdaae1.jpgleg2.jpg.287a0c3117f0d830c560c25af4117223.jpg

 

Length is not set yet, still haven't gotten measurements for the final design, but imagine a drawer box and flat top on top of this leg.   The maple will have a 1/2" x 1/2" rabbet cut into it where the cherry will be glued in.  Then the taper will be cut, giving the diminishing look to the cherry. 

In my mind, I'm kinda digging the look of this, not too much extra, but enough for the legs to have some character to them.   I'm also thinking of all the cherry/maple glue lines to be accented again by a very thin walnut veneer, just enough to help accent the cherry, and make the glue lines look crisper.  

Posted

I like the cherry border on the top,but the leg is kinda throwing me. The digital image looks off, but I think the real thing might look ok.

I might consider making it narrower, though.

 

*Wait! I see it now - the taper would have to be on the outside for that cherry to show. Square legs with tapers on the outer sides make a table look tippy & unbalanced. How about a cabriole or semi-cabriole leg with that cherry streak? 

Saw how to cut semis just this morning:

 

  • Like 2
Posted
20 hours ago, wtnhighlander said:

Wait! I see it now - the taper would have to be on the outside for that cherry to show. Square legs with tapers on the outer sides make a table look tippy & unbalanced. How about a cabriole or semi-cabriole leg with that cherry streak? 

Yes!  That was my first vision of the leg.  But I am no place just yet to do cabriole.   This would be a proof of concept type project too.  If the junction between the tip of the cherry and the taper is not healthy, I would hate to ruin a cabriole leg with a bad glue line... 

I'll probably do the final legs with tapers on all 4, cause yeah, I'd think tapers on two sides only will just look goofy. 

I have a piece of scrap maple from work I'm going to run as a test leg tonight, I'll post some pics, and see if she likes it (I know she'll say yes, but still).   I also will make some 90* mitre cauls for this glue up, which will might work for miter joints too.  

  • Like 1
Posted
On 9/27/2017 at 9:28 PM, K Cooper said:

Me, I like it! But I bet come hell or high water, you'll get some push back from the racing stripe folks;)

Consider me part of the racing stripe folk. Aesthetically, it's not my bag. That said, I hope you do it, because I am curious to see how this one turns out!

  • Like 2
Posted
3 hours ago, Dknapp34 said:

Consider me part of the racing stripe folk. Aesthetically, it's not my bag. That said, I hope you do it, because I am curious to see how this one turns out!

x2 I look forward to seeing it as well :)

Posted

The trouble I see with the design is that you're going to have to nail the taper perfectly to have the cherry section end up the same length in all 4 legs. Any tiny variation will be magnified by the steep angle and be extremely visible. For me, I'd be inclined to alter the proportions so the cherry reaches the floor (maybe put less taper on the outside of the leg with the inlay), but I'll be curious to see what you end up with.

  • Like 1
Posted

I would glue up some test pieces out of scrap using the same dimensions as your cherry/ maple parts. Poplar is what I would use. Practice your cuts on those before you start on the good stuff. 

Posted
3 hours ago, wdwerker said:

I would glue up some test pieces out of scrap using the same dimensions as your cherry/ maple parts. Poplar is what I would use. Practice your cuts on those before you start on the good stuff.

 

They are scraps.  The maple may be figured, but it has a bunch of screw holes down the sides, it was used as blocking material for a cabinet mock up.  Cherry is part of a smaller piece I had laying around.    One of the bonuses of working in a Mill house, about half the stuff we toss get's pulled from bin and into somebodies car.    I ended up snagging 4, 1"x6"x7' beautiful wlanut pieces today, all with perfect straight grain.  Not figured or anything, but with the right finish, they will glow.   Our buyer doesn't muck around, if it's not primo, we don't use it.  They will be the majority of a chess board table.  My father was given a 36"x36" chess board veneer made of walnut and maple with cherry accents around the border.  I'm planning on using the walnut for the majority of the table, and then doing this style leg ina simple cabriole cut, with maple drawer pulls.  Maybe even raised maple panels for the sides and drawer fronts.  Given the veneer will be placed on a piece of good ply (I also snagged a bunch of BB ply from some shipping crates the other day, just gotta trim the edges), the build should be fairly simple. 

But basically, I'll never see poplar at work, we use maple as our trash wood, and mahogany for any of our structural pieces.  Poplar costs me money, maple is free.  Oh yeah, also snagged a nice 2"x2"x12" lump of Ipe today too.  I'll turn that with a good sized lump of mahogany for a mallet, maybe oak, I dunno. 

The actual legs will be from the clean maple blocking material we use, there's a lot of nice figured stuff on the rack. 

Posted
8 hours ago, SawDustB said:

The trouble I see with the design is that you're going to have to nail the taper perfectly to have the cherry section end up the same length in all 4 legs. Any tiny variation will be magnified by the steep angle and be extremely visible. For me, I'd be inclined to alter the proportions so the cherry reaches the floor (maybe put less taper on the outside of the leg with the inlay), but I'll be curious to see what you end up with.

That is also my concern.  But I've been sick all week, and pulled extra hours at work to make it worse, else I'd already know.   My taper jig I'm going to build, hopefully sunday, will be a repeatable setup, so the cuts should be identical.  I'm ok with slight variations in the actual length, as the legs will be far enough apart, they shouldn't be noticeable without a ruler.   But your idea of taking the cherry all the way to the floor is also an idea I'm considering, but then we're pushing into 'racing stripe' territory. 

I'm also consider a layer of walnut veneer in the glue line.  I know I'm going to try it in the inlay on the table top, so I'd like to have the same look in the legs.   It will either hide the variance, or scream here I am.   Of course I'm also worried that it may get left exposed in an exaggerated way in the taper too.    But like I said, it's an experiment.   If the prototype doesn't go as planned, oh well. 

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 75 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined