SawDustB Posted September 29, 2017 Report Posted September 29, 2017 At my 4 year old daughter's request, I'm remaking some picture frames in her room. Right now they're just cheap plastic ones. I took her to the wood store and chose purple heart for the main wood. I had a plan, so I got her to pick a second wood and she went with curly maple (apparently bird's eye looked funny). I started by edge jointing my purple heart. The leg vise and dead man are awesome for this. Next up, I ripped my board in two and planed it down, keeping maximum thickness. It ended up just over 7/8". It's a lovely brown color now, but it'll get its purple back. 1 Quote
SawDustB Posted September 29, 2017 Author Report Posted September 29, 2017 Next up was the curly maple. The plan is to make 3 frames, with one being mostly maple and the others mostly purple heart, with accents and splines of the other wood. I edge and face jointed the maple and then ran out through the planer and table saw to clean it up. I realized the edge had more curl than the face. The project plan changed a bit. I decided that rather than keeping each frame piece solid (at about 2 inches wide) I'd rip them into strips and turn them on edge. This works because the seam falls where I was going to do an inlaid molding anyway. 1 Quote
SawDustB Posted September 29, 2017 Author Report Posted September 29, 2017 I ripped all the strips down and realized that my frames would now be 1 3/4" wide. I still wanted at least my 2", so I'm gluing in a 1/2" strip of plain maple (Roubo scraps). This won't be seen with the piece being inlaid in the front, and these will be hung on the wall. Each of these pieces will give me a long and short piece for each frame. They were a little crooked after gluing, but I straightened them out with a plane and the table saw. I had to sharpen my low angle smoother at about 40 degrees to keep the tear out under control. 1 Quote
Popular Post SawDustB Posted September 29, 2017 Author Popular Post Report Posted September 29, 2017 The next step was to make the molding to be inlaid in the middle of each frame piece. I took a piece of purple heart and maple, and used a 1/4" round over bit in the router table to create the profile. I did it in a heavy and finish pass to try and get a smoother finish. I then used the table saw to rip the molding off and then used the router to profile the edge again. Once I was done, there were contrasting molding for each frame piece. These are not glued in yet, but they give a rough idea of what this will look like. Next up is to make the groove they'll fit into and profile the edge of the main frame pieces. 4 Quote
Eric. Posted September 29, 2017 Report Posted September 29, 2017 This thing is awesome for use with the deadman. http://www.leevalley.com/us/Wood/page.aspx?p=57059&cat=1,41637 2 Quote
pkinneb Posted September 29, 2017 Report Posted September 29, 2017 Thanks for taking us along...I am thinking about doing a couple frames for xmas this year so this is perfect timing. 1 Quote
SawDustB Posted September 29, 2017 Author Report Posted September 29, 2017 9 hours ago, Eric. said: This thing is awesome for use with the deadman. http://www.leevalley.com/us/Wood/page.aspx?p=57059&cat=1,41637 Awesome, thanks. The holdfast worked, but I didn't really like whacking it in. That looks like a better option. I should have mentioned, I've been asked by my wife to make this sort of match the profile of an existing frame that I made from pine. They're in the same room, and she likes having a theme. Here's the profile of that frame so you can sort of see where this is going: I'm not matching it exactly, since the new frames will be a bit narrower. There won't be the V groove on the inside of the frame, but otherwise it will be similar. Quote
SawDustB Posted September 29, 2017 Author Report Posted September 29, 2017 I hada few minutes to do a bit of routing today at lunch. First up, I cut the grooves for the molding to go into. The molding is just over 3/4", so I used a 3/4" bit and made a pass, flipped it and made a second pass. This gave me a centered groove at the right size. In the picture you can see one of the pieces test fit, along with the groove. It's a very tight fit, but that's good. Any gaps would be very obvious. Next up I cut the ogee on the inside of the frame pieces. I find this is better to do first, then the rabbets for the glass can easily be cut using a straight bit and the fence. I need to put a round over with a shoulder on the outside of the frame, then all that's left is the rabbet (at the router table, anyway). 1 Quote
SawDustB Posted September 30, 2017 Author Report Posted September 30, 2017 I got an hour tonight to keep going. I put the round over on the pieces, although I realized my router bit wasn't cutting very well. I had a lot of burning and tear out to clean up. I used a chisel and scraper for a lot of it, followed by sanding. I put a tiny chamfer on the underside of the molding and glued them in. I clamped them all up together. The fit was very tight, so the clamps were needed to seat them. The only issue I see so far is that a couple of the ends have a bit of variation in the molding height. There may be some chisel work to make them meet once I assemble the frames. 2 Quote
SawDustB Posted September 30, 2017 Author Report Posted September 30, 2017 And after coming out of the clamps, thus is what I've got. Only a tiny bit of glue squeeze out to clean up, and then I'll cut the rabbet. It will be pretty deep in these frames because I'm using a mat (11x14 with a 8x10 picture). 2 Quote
Popular Post SawDustB Posted September 30, 2017 Author Popular Post Report Posted September 30, 2017 And with some more time at the router table, I have the rabbet. I find it works best to cut very lightly up to full depth, then work up to the width. That avoids most of the splintering that sometimes happens. Especially with purple heart. If I remembered how many passes this takes, I likely would have just taken the time to put in the dado set. 3 Quote
Popular Post SawDustB Posted October 2, 2017 Author Popular Post Report Posted October 2, 2017 I cut all the frame pieces to rough size. I checked my miter saw, and couldn't get a good cut so I decided to use my crosscut sled. I used a drafting triangle to set up a fence attached with double sided tape, then put in a couple screws from the underside. For the other side, I set up a second fence at 90 degrees to the first. I used the sled itself as the stop, so I was able to cut all the short sides. They fit well in a test assembly. Next up I'll reposition that fence and cut the long sides to length. ... And as usual, when making frames, I cut one of the pieces with the miter going the wrong way while I was checking my setup. Every. Single. Time... Unfortunately, I had cut all the pieces to rough length. The only fix was to glue the cutoff back on and recut the miter. Depending on how it looks, this may end up being a smaller frame. 3 Quote
davewyo Posted October 3, 2017 Report Posted October 3, 2017 1 hour ago, SawDustB said: ... And as usual, when making frames, I cut one of the pieces with the miter going the wrong way while I was checking my setup. Every. Single. Time... I just did the same thing about a half hour ago. It was no big deal for me because I had milled more stock than I needed, but I do it "Every. Single. Time..." too! 2 Quote
SawDustB Posted October 3, 2017 Author Report Posted October 3, 2017 10 hours ago, davewyo said: I just did the same thing about a half hour ago. It was no big deal for me because I had milled more stock than I needed, but I do it "Every. Single. Time..." too! It's good to know I'm not alone. Usually it's not an issue, because I'm just cutting them out of a length of molding. The problem was I cut it upside down because I was trying to use a single miter setup on the sled. I think it'll be OK. It's almost invisible after gluing. Quote
Popular Post SawDustB Posted October 4, 2017 Author Popular Post Report Posted October 4, 2017 I got all three frames glued up. The miters aren't perfect, but I'm reasonably happy. I ended up just clamping with blue tape and using super glue as clamps. On the maple frame I've got the repaired miter. Here it is after gluing the frame. I think it turned out OK. Next up I need to add in the splines, then lots of sanding. 4 Quote
Coop Posted October 4, 2017 Report Posted October 4, 2017 If you hadn't done a close up and pointed it out, the mistake would never been noticed! Good recovery. 1 Quote
Larry Moore Posted October 4, 2017 Report Posted October 4, 2017 I had to look really hard to find it. Once it's on the wall no one will see it. 1 Quote
SawDustB Posted October 5, 2017 Author Report Posted October 5, 2017 Thanks guys. I won't point it out to anyone else, but I figured I'd be honest on here. I cut the spline recesses in the frames using my very lovely spline jig. Similar to the miter sled, building a decent one is on my list but i made this work. I realize it looks like it's just taped on, but I did hot glue it until place as well. It was made for my old table saw and sled, so I had to shim it out from the fence. Next up I tried to glue the splines. The maple frame went well, but disaster struck with the first purple heart frame. The spline stuck going into the first corner, and my glue joints broke apart when I tried to tap it in. I had to walk away for a bit, but I did manage to reassemble it with the help of some CA glue. The joints aren't perfect, but they're pretty close to where they were before. 2 Quote
Popular Post SawDustB Posted October 5, 2017 Author Popular Post Report Posted October 5, 2017 I glued in all of the splines, after taking a card scraper to the maple ones to take a few thousandths off. I remembered after the first frame to blue tape around the splines to help with squeeze out. If I'd been smart, I would have taped before cutting the recesses for the splines. The leg vise is fantastic for working on this. I did also glue the splines into the damaged frame, so I'm back on track. Only the maple frame was dry enough to cut off the splines, so I could see what it's going to look like. While things didn't exactly go according to plan, I should be able to move on to sanding next. I picked up some contour sanding blocks at Lee Valley earlier to help. 3 Quote
Coop Posted October 5, 2017 Report Posted October 5, 2017 From your pic, I can't tell, but are you using something similar to this to cut your splines? It's about as simple as you can get. Quote
SawDustB Posted October 5, 2017 Author Report Posted October 5, 2017 8 hours ago, K Cooper said: From your pic, I can't tell, but are you using something similar to this to cut your splines? It's about as simple as you can get. Here's another angle on the jig. I glued it together from a couple of pieces of wood that were laying around, thinking I'd toss it after that project and make a better one. That was almost three years ago. It's just a couple of pieces of 1/4" ply glued onto a couple of chunks of deck board that are in there at 45 degrees. It works, but it's not really stable enough to use without riding on my sled. I use it pretty rarely though. Quote
SawDustB Posted October 6, 2017 Author Report Posted October 6, 2017 I used a flush trim saw and a cranked neck chisel to bring the splines down to flush last night. Not looking too bad at this stage: There's a fair bit of glue stain on the surface with some of them, so I'm probably going to resort to putting a fine belt on the stationary belt sander and doing all of the sides. As far as the rest of the profile goes, the purple heart looks pretty good but I have some tear out to sand down on the curly maple. For hanging, I'm just planning to route in keyhole slots so I may do that now, as opposed to later when I might scratch the finish. 2 Quote
gee-dub Posted October 6, 2017 Report Posted October 6, 2017 Looking good. I agree on doing the keyhole slots before things get too “finished”. Key holes are my favorite method of hanging smaller items. 1 Quote
SawDustB Posted October 6, 2017 Author Report Posted October 6, 2017 3 hours ago, gee-dub said: Looking good. I agree on doing the keyhole slots before things get too “finished”. Key holes are my favorite method of hanging smaller items. Thanks!, Yeah, me too. I can't stand having the pictures tilted out at an angle because of hardware being back there. I find it takes me about the same amount of time as it would to install a lot of the other options anyway. I want these up pretty securely too, since they're above my daughter's bed and she sometimes lays there kicking the wall at night if she can't sleep. I have no idea why. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.