jpf1182 Posted November 20, 2017 Report Posted November 20, 2017 I am in the market for an 8 inch jointer. I would prefer helical cutter head and parallelogram tables . I have had the Grizzly model on order for months and it now seems that they won't be available until April!! I don't want to spend $3000 for another manufacturer so it looks like I may have to forgo the parallelogram beds. Do you all think the standard beds are an issue. I understand they are very difficult to adjust if out of parallel. I am looking at the Powermatic and Jet models at the moment. Please give me your opinions. Another manufacturer? I understand the Steelex is basically the same as Grizzly and it will be available in December. Thanks. Quote
Brendon_t Posted November 20, 2017 Report Posted November 20, 2017 I've got an 8". Delta clone with normal beds. It's a pain to adjust, about once or twice a year. Essentially, only when I move everything out of the shop to clean or rearrange. If buying a new unit tomorrow, parallelogram beds would not be as important factor for me as it's ability to hold a setting and work reliably. Because of those, I wouldn't shop grizzly. Quote
minorhero Posted November 20, 2017 Report Posted November 20, 2017 I have 50 year old wedge bed and have no issues. If the beds get out of wack (which requires either damage, extreme wear, or really bad quality out of the gate) than you need shims to get them square and can take a few days of adjusting to get it right. I have previously owned a grizzly wedge bed jointer with no issues. The best alternative to grizzly is Shop Fox. It's made by grizzly, comes with a longer warranty and is sold by other outlets rather than just through grizzly themselves. Good luck! Quote
Jfitz Posted November 20, 2017 Report Posted November 20, 2017 If I had to give up a feature, I'd most likely give up the helical head in lieu of the parallelogram tables - you can add a helical head later if you want, but you can't add parallelogram tables. At least, this is my reasoning when I think about eventually upgrading to an 8" jointer. Interested to see where this post goes. Also....Part of my reasoning is that I have a helical head on my planer, so as long as I can get something flat in some way on the jointer, I mostly let the planer deal with any tough grain. 1 Quote
Chestnut Posted November 20, 2017 Report Posted November 20, 2017 1 hour ago, jpf1182 said: I am in the market for an 8 inch jointer. I would prefer helical cutter head and parallelogram tables . I have had the Grizzly model on order for months and it now seems that they won't be available until April!! I don't want to spend $3000 for another manufacturer so it looks like I may have to forgo the parallelogram beds. Do you all think the standard beds are an issue. I understand they are very difficult to adjust if out of parallel. I am looking at the Powermatic and Jet models at the moment. Please give me your opinions. Another manufacturer? I understand the Steelex is basically the same as Grizzly and it will be available in December. Thanks. The PJ 882 is an outstanding jointer i have one. The strait blade model will be onsale over black friday weekend 10% off which puts it at just shy of 2k which is still considerable more than where your at. The Helical head for it from byrd is like $450 which means you could get the $3200 jointer for $2500 ish. leaving you the ability to save for the helical head to buy later. just a thought. Jet would probably be an okay option. The problem is with $2500 is the 12" grizz seems to be a pretty decent jointer and isn't much more but offers 4" more capacity. Quote
Just Bob Posted November 20, 2017 Report Posted November 20, 2017 Last month I bought the Grizzly G0490 (straight knife) jointer, because they were out of stock on the helical head models. At the time it was on sale for 935. At the same time I bought the Byrd Shelix head through Grizzly. The combined price came in very close to their model with the Grizzly helical head. I swapped heads as I set it up, and I really like the jointer. The head swap was very easy. I just checked the Grizzly site and they are now out of stock on the straight knife model. Check Steelex, except for color, their jointers look to be identical to Grizzly models and I think they have a better warranty. I really like the parallelogram tables, and hh head, be patient and get what you want. Quote
jpf1182 Posted November 20, 2017 Author Report Posted November 20, 2017 Thanks for the input. The Shop Fox and Steelex are also out of stock until April! I had thought about swapping out the Grizzly blades for the helical head but, as you said, that model is also out of stock. I am leaning toward either a Jet or Powermatic with helical heads and wedge tables. Woodworkers used them for decades. Money isn't the biggest issue....I just don't want to spend a huge amount since I am a weekend warrior. Quote
Unknown craftsman Posted November 20, 2017 Report Posted November 20, 2017 The only adjustments on a new jointer should be moving the fence and the depth of cut. If the tables are not ground coplaner from the factory send it back. You don't want to go down the road of aligning jointer tables. And when you get a new jointer don't lift it from the end of the tables. Good luck Quote
minorhero Posted November 20, 2017 Report Posted November 20, 2017 4 hours ago, jpf1182 said: Thanks for the input. The Shop Fox and Steelex are also out of stock until April! I had thought about swapping out the Grizzly blades for the helical head but, as you said, that model is also out of stock. I am leaning toward either a Jet or Powermatic with helical heads and wedge tables. Woodworkers used them for decades. Money isn't the biggest issue....I just don't want to spend a huge amount since I am a weekend warrior. Because shop fox is sold by other stores there may be folks who have it in stock right now. You should try calling around. A Google search showed several retailers listing it as in stock. Quote
bushwacked Posted November 20, 2017 Report Posted November 20, 2017 4 hours ago, jpf1182 said: Thanks for the input. The Shop Fox and Steelex are also out of stock until April! I had thought about swapping out the Grizzly blades for the helical head but, as you said, that model is also out of stock. I am leaning toward either a Jet or Powermatic with helical heads and wedge tables. Woodworkers used them for decades. Money isn't the biggest issue....I just don't want to spend a huge amount since I am a weekend warrior. you can get the 8" PM straight knife wedgebed from amazon for like $1790 right now ... Quote
Alan G Posted November 20, 2017 Report Posted November 20, 2017 8 hours ago, jpf1182 said: I am in the market for an 8 inch jointer Where are you located? I am looking to sell my Grizzly. Its an 8" straight knife parallelogram bed. Quote
Alan G Posted November 21, 2017 Report Posted November 21, 2017 Okay well your about 4hrs away. I'm in Ann Arbor, MI. Quote
LazarusDB Posted November 27, 2017 Report Posted November 27, 2017 On 11/20/2017 at 9:34 AM, jpf1182 said: I am in the market for an 8 inch jointer. I would prefer helical cutter head and parallelogram tables . I have had the Grizzly model on order for months and it now seems that they won't be available until April!! I don't want to spend $3000 for another manufacturer so it looks like I may have to forgo the parallelogram beds. Well that really sucks as I have the same one on order. You're talking about the G0490X right? The only 8" they do have in stock is the G0495X but that thing is nearly 800 pounds. Guess I need to look at the Powermatic 60HH. No parallelogram beds but I guess there are worse problems to have. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.