Hayseed Posted January 6, 2018 Report Posted January 6, 2018 I have an elcheapo table saw 100 dollar ryobi. When converting to sanding disk of 14 inches, it vibrates like crazy. It is direct drive. Table saw is a 10 in her. It seems the table is made so cheap that the 14 inch out of balance, I am sure wheel, can't be properly stabilized. Table is made of plastic and cheap sheet metal. Motor is 15 amp and spins like crazy. Thinking I should make a wooden housing to hold motor and wheel, and to also add pulley system to help with vibration and to slow down the rpm's. Any one with new eyes that can help with some suggestions? Thanks 1 Quote
wtnhighlander Posted January 7, 2018 Report Posted January 7, 2018 Is the sanding disk something you made, or a commercial product? Sounds like it is out of balance. If so, you may dampen the vibrations by beefing up the supports, but the forces are still there, and will eventually damage the machine. And why a 14" disk? Those little saws make up for lack of torque by spinning at 5000 rpm. That means the rim of your disk is moving at over 200 miles per hour! Quote
wdwerker Posted January 7, 2018 Report Posted January 7, 2018 Save up for a better saw , then save up for a dedicated sander. Lots of us have the Ridgid osselating spindle and belt sander combo. I've never even thought about a disc sander since I bought mine. Trying to rig something that could be run by your old saw would eat up a bunch of time, require multiple trips to the hardware store and probably be rather dangerous. It's amazing how fast the price of the parts & fasteners adds up. Now if a friend or relative has a machine shop , lots of free time and is willing to help ...... Quote
Hayseed Posted January 7, 2018 Author Report Posted January 7, 2018 The table saw is an extra. Figured to cut a disk and sand paper slap it on the old saw, and waalaa! Why 14 "? I figued I would have more sanding area prompting less sand paper changes. I can save up, not really, live on fixed income, and initially started this as a fun project. Quote Quote
Woodenskye Posted January 7, 2018 Report Posted January 7, 2018 If you really want to continue doing this, I would go back to a 10" disc. Quote
Popular Post minorhero Posted January 7, 2018 Popular Post Report Posted January 7, 2018 If your disc is out of balance by even an ounce or so you will get vibration. Honestly if it were me I would stop. Not because of fear of damaging the saw (which is a very real scenario) but rather out of fear that something might fly off and hit me causing an injury. 3 Quote
Wimayo Posted January 15, 2018 Report Posted January 15, 2018 On 1/6/2018 at 7:48 PM, Hayseed said: Figured to cut a disk and sand paper slap it on the old saw, and waalaa! I interpret this as saying that you cut a disc out of wood. If so, it is most certainly out of balance and you need to discard it. I have used one of these for many years and it works very well on either table saw or radial arm saw. You might find a cheaper one on ebay, craigslist, etc. Quote
Bankstick Posted January 16, 2018 Report Posted January 16, 2018 I bought the sanding disk, #129272, from Woodcraft- 10 inches and you can get different grits for it. Handy as a pocket on a tee shirt. Only negative is if you are only doing one piece is changing the TS blade. Quote
woodbutcher74 Posted January 16, 2018 Report Posted January 16, 2018 I tried the sanding disc on my old Craftsman saw. The RPMs on a tablesaw are a lot higher than most sanders. It sounded like a jet engine when you fired it up. In my experience it burned the wood almost as soon as it touched the disc. Just my experience. Quote
Wimayo Posted January 16, 2018 Report Posted January 16, 2018 I think a sanding disc should run about 1750 rpm. You can do an internet search to find out for sure. If you are going to use an old direct drive table saw as a dedicated sander and the motor is going too fast, I guess the only solution is to find a slower replacement motor. Quote
Bankstick Posted January 17, 2018 Report Posted January 17, 2018 I cut 24 pieces of PVC pipe for a school project. Then I used it to square 24 pieces of PVC pipe- this with the WC disk. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.