Popular Post Tom King Posted April 5, 2019 Popular Post Report Posted April 5, 2019 This will be 4-board pasture fencing. We did have it up at the edge of those woods behind it in the picture. With our numbers of horses way down, we don't need every square foot of pasture, and that spot uphill has been the most trouble for clipping, with gullies, and rock outcroppings, so I decided to move the fence downhill below the problem areas, and just let it grow back up in Pine trees. For building a nice looking fence on uneven ground, it's better not to just measure off the ground level, and put the boards on. Posts are set not quite touching strings pulled, high and low, on the side opposite that the boards will go on. If any post pushes the strings, it gets impossible to keep it nice and straight, whereas staying within a quarter inch of the line makes it look perfectly straight to the eye. These posts were set on more level ground, up near those woods, and set on 8' centers. Since the new location is more undulating, I shortened the center spacing to 93 inches, to make sure none of the old boards ran too short. On both undulations, and curves (made in straight 16' sections so bending boards don't push the posts out over time) you can't stagger the boards, or the spacing gets all wonky. Once your posts are set, go along and mark every post with a magic marker at the top of the top board location. In this case, that is five feet. You only need to mark every other post if it's a fairly flat run, and you are sure all boards will span two post gaps. On undulating ground, sometimes you will need to use short boards, so go ahead and mark every one. I didn't do this yesterday, so had to make a second trip down the line after we got to a section that needed short boards to just catch two posts. NOW HERE IS THE TRICK TO MAKING AN UNDULATING FENCE LOOK NICE: Once you have the top marks, screw the top boards in place with only one screw on each end. Stand well back and look at it. Some board intersection locations will need to be cheated up, or down, to make the flowing lines smooth, without zagged slope changes. We ended up changing over half of the board joints, and one as much as three inches, to get it to look like this. We just let the boards run long, and overlap on the posts for now. When we get back to work on it, I'll take a small chainsaw, and cut the overlapping boards in place to fit on the posts, end to end. I have plenty of other stuff to do, but wanted to catch this before the ground got hard for digging the holes, even with a 2-man auger, and before the grass started growing, since we have that pasture closed off to the horses until I get the fence done. edited to add: After looking at these pictures, I will go back and ease up that second joint from the right. With only one screw in each end of each board, it's not too much trouble, with a helper. 4 Quote
Tom King Posted April 5, 2019 Author Report Posted April 5, 2019 That fence is visible from the dogroom on the back of our house. It's raining today, so we didn't work outside. Looking at the bigger view, with more fence that I couldn't get in the frame of the picture, and see the fence to amount to anything, rather than raise that one spot, I'm going to lower the joint on the right edge of the first picture. That low spot is in the end of a low part between two swales. The idea of using 4-board, rather than 3-board, is to keep large dogs out of the pasture. Using 5-1/2" 2x6's for the fence boards, that leaves 9-1/2" spaces, which large dogs don't fit through. If I raised that one low spot, it would leave too large of a gap under the lowest board. By lowering the one joint, the space under the lowest board will be smaller, but the lines of the fence will flow better. 1 Quote
Coop Posted April 6, 2019 Report Posted April 6, 2019 That looks like hard work but obviously that and attention to detail paid off. Very nice. Tom, I need to have a cedar/picket type fence replaced. This is one replaced by my neighbor after a hurricane and he used landscape timbers as post and attached the pickets with drywall screws. Since he was kind enough to put the pickets on my side and as he works on weekends, I was able to go behind him on weekends and replace the screws without embarrassing him. Anyway, the landscape timbers are giving way and I’ve dug all the post holes I intend to dig. I’d like this to be structurally sound for 20 years. On bids, I’m going to ask the contractors for 3 vertical rails, 4x4 treated posts, full 3/4” pickets and a rot board horizontally across the bottom. Any suggestions for the post/holes. Depth and distance between. In Houston there is no frost line but plenty of rain and dry spells. Thanks Quote
Tom King Posted April 6, 2019 Author Report Posted April 6, 2019 It'll look a lot better when it's done. It really wasn't that bad. I don't remember exactly what year I built that fence, that all these parts came out of, but it was put together with decking screws, from back when decking screws were just galvanized sheetrock screws with Phillips heads. I was surprised that almost all of them came right out. It's probably the old type of pressure treating, and all the posts are really in good shape. I did toss a few of the fence boards, but we had extra from the edges of that pasture that was shortened. I pulled the trailer along the fence line, and we put the boards on one side of the trailer, then went back the other way, and Big Mike shook the posts, pulled them up, and put them on the other side of the trailer, as I creeped the trailer along. I have a tractor auger, and a 2-man, but hadn't used my 2-man in over a decade. The tractor auger works good on flat ground, but is more trouble than it's worth on uneven ground. I rented a 2-man. The rental place I like is 40 miles away, but got it back in time to only pay the 4 hour rental rate. We caught the ground just right, and each hole took maybe ten seconds. That run of fence is only about 240 feet long. Quote
Tom King Posted April 6, 2019 Author Report Posted April 6, 2019 10 hours ago, K Cooper said: That looks like hard work but obviously that and attention to detail paid off. Very nice. Tom, I need to have a cedar/picket type fence replaced. This is one replaced by my neighbor after a hurricane and he used landscape timbers as post and attached the pickets with drywall screws. Since he was kind enough to put the pickets on my side and as he works on weekends, I was able to go behind him on weekends and replace the screws without embarrassing him. Anyway, the landscape timbers are giving way and I’ve dug all the post holes I intend to dig. I’d like this to be structurally sound for 20 years. On bids, I’m going to ask the contractors for 3 vertical rails, 4x4 treated posts, full 3/4” pickets and a rot board horizontally across the bottom. Any suggestions for the post/holes. Depth and distance between. In Houston there is no frost line but plenty of rain and dry spells. Thanks We must have been posting at the same time last night, or else, I was too sleepy to see the second part. I built some temporary fence, with electric tape, years ago using landscape timbers, and it ended up being a lot more temporary than I had hoped for. Did you mean 3 horizontal rails? 2 feet should be plenty deep enough for the holes, unless your subsoil is just sand there. That's what I use on the pasture fence, but our subsoil is red clay. If made out of treated lumber, it should last 20 years. I don't remember when they changed treating method, but the new stuff doesn't last but a few years if a post is put in concrete. I built some fencing with the new stuff, when it first changed, and anything that was not seated in concrete is still good. I put one 6x6 gate post in concrete, and I don't think it lasted but about three years. If the fence is not really long, post spacing shouldn't make a great deal of difference in final cost, so I would go 4, or 6 foot spacing on the posts, to keep a picket fence as straight as possible. I would think a fencing contractor would have recommendations, and have a good feel for it there. Don't let them use nailgun nails in a fence. 1 Quote
wtnhighlander Posted April 6, 2019 Report Posted April 6, 2019 I agree with Tom about posts in concrete. Red clay soil here, as well. I tamp the backfill pretty tight, and the posts are rock solid. Haven't found one rotten yet, either. Mine are at least 15 years old. Filling the post hole with concrete allows water to be trapped around the post, as even treated lumber moves with changes in moisture. Movement opens gaps around the post, and the concrete form a bucket to hold water. If the soil is too soft or sandy, put dry gavel in the bottom of the hole, then the post, then concrete. That leave some way for water to escape. Quote
Byrdie Posted April 8, 2019 Report Posted April 8, 2019 We had really sandy soil and shallow water when I lived on the farm so i second the gravel at the bottom of each hole. Kept the bottoms of the posts dry and made them last longer. Quote
Popular Post Tom King Posted April 11, 2019 Author Popular Post Report Posted April 11, 2019 We made an early start this morning, to be the heat that we aren't used to yet, and finished this stretch of fence. It looks a lot more jagged, when you look down the fence line, that looking at it straight on. I left the line behind the posts, and we'll go back, and tamp the posts back into line later. The boards had laid on the ground through a rainly spell, so some darkened up from the ground, but will lighten back out when they dry. We ended up dropping that joint in the far right of the first picture one inch, and it evened out the flow of the whole fence. The ground under the fence is a lot more up, and down than the finished fence. The difference is in the standing back, and looking at the top board before final fastening of everything. Pam said it looks good, so it passes the best test. 4 Quote
Tpt life Posted April 11, 2019 Report Posted April 11, 2019 Natural colors look better than white when lines aren’t perfect. Naturally growing things vary from flatter to rounder as does the ground. It looks very good and taught me an approach to “fairing” the curves I had not considered before as fences are a once a decade thing for me. Quote
drzaius Posted April 11, 2019 Report Posted April 11, 2019 I commute from a bedroom community so I see a lot of rural fences & I certainly appreciate a nice looking one. I wish more people took this much care when building their fences. Quote
Bankstick Posted April 12, 2019 Report Posted April 12, 2019 My uncle's farm had a board fence only along the road. The owner was cheap and only painted the part facing the road! That is a nice fence! Used to see miles of white wood fences around horse farms in KY. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.